Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The engine control unit communicates with the TCM using the Controller Area Network (CAN).

If there is a problem in this communication, the TCM sets a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0100 Lost Communication with ECM / PCM "A" Following conditions are met for 1.25 seconds (1 trip detection logic):
·

Ignition switch ON

·

Battery voltage is 10.5 V or more

·

No communication between the engine control ECU (ECM) and TCM


·

Harness and connector

·

ECM

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C262132E04
0.979,4.469 3.073,4.708 2.094,0.24 10 false : CAN Communication Line 6.26,4.083 6.635,4.271 0.375,0.188 10 false TCM 3.021,2.198 3.396,2.385 0.375,0.188 10 false ECM 0.281,0.917 1.219,1.323 0.938,0.406 10 false from EFI NO. 2 fuse 3.531,1.125 4.042,1.427 0.51,0.302 10 false CAN+ 3.552,1.615 4.063,1.844 0.51,0.229 10 false CAN- 5.927,1.115 6.417,1.406 0.49,0.292 10 false CAN+ 5.927,1.625 6.406,1.854 0.479,0.229 10 false CAN- 2.656,1.781 3.01,2.042 0.354,0.26 10 false E1 5.615,1.135 5.99,1.396 0.375,0.26 10 false E7 3.979,1.635 4.365,1.854 0.385,0.219 10 false E26 3.979,1.135 4.365,1.354 0.385,0.219 10 false E26 5.667,0.948 5.844,1.229 0.177,0.281 10 false 6 5.677,1.438 5.927,1.667 0.25,0.229 10 false 7 4.073,1.448 4.271,1.604 0.198,0.156 10 false 1 4.031,0.958 4.333,1.198 0.302,0.24 10 false 31 2.365,1.198 2.573,1.479 0.208,0.281 10 false 3 2.375,0.802 2.573,1.073 0.198,0.271 10 false 2 5.615,1.625 5.99,1.865 0.375,0.24 10 false E7 2.281,0.99 2.698,1.219 0.417,0.229 10 false A25 2.292,1.385 2.729,1.635 0.438,0.25 10 false A25 2.333,1.604 2.771,1.844 0.438,0.24 10 false 49 2.615,1.385 3.104,1.615 0.49,0.229 10 false +B2 2.625,0.979 3.167,1.188 0.542,0.208 10 false +B 2.292,1.781 2.729,2.094 0.438,0.313 10 false E26

CAUTION / NOTICE / HINT

HINT:
·

Refer to inspection procedure for CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive the current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is effective to find malfunctions.

·

The malfunction area can be checked using the Bus Check function on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (+B AND +B2 TERMINALS)
a.
A255690C52
0.365,0.948 0.792,1.208 0.427,0.26 1.573,1.135 1.219,1.688 1.219,1.688 0.833,1.688 true 1.677,1.135 1.198,1.917 1.198,1.917 0.833,1.917 true 0.177,0.156 0.333,0.313 0.156,0.156 10 false *a 0.573,1.594 0.813,1.792 0.24,0.198 10 false +B 0.458,0.979 0.75,1.177 0.292,0.198 10 false A25 0.521,1.865 0.823,2.104 0.302,0.24 10 false +B2
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A25-2 (+B) - Body ground Ignition switch ON 11 to 14 V
A25-3 (+B2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-49 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-6 (CAN+) - E26-31 (CAN+) Always Below 1 Ω
E7-7 (CAN-) - E26-1 (CAN-) Always Below 1 Ω
E7-6 (CAN+) or E26-31 (CAN+) - Body ground and other terminals Always 10 kΩ or higher
E7-7 (CAN-) or E26-1 (CAN-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK IF DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK IF DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.


Powertrain > ECT > Clear DTCs
50002 235
c.

Replace the TCM.

HINT:

Replace the TCM with a TCM from a normally functioning vehicle of the same model.



d.

Start the engine.


e.

Read the DTCs.

Powertrain > ECT > Trouble Codes
50001 235
Result:
Display (DTC Output) Proceed to
U0100 A
No DTC B




A

B