Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM M

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  REGISTRATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When the automatic transaxle is replaced, the transaxle compensation code must be input into the TCM (proceed to Procedure 1). After the automatic transaxle is reinstalled, the Quick Response (QR) code label will be positioned where the code cannot be read. Therefore, before reinstalling the automatic transaxle, record the transaxle compensation codes or input them in the intelligent tester.

·

When the TCM is replaced, the existing transaxle compensation codes must be input into the new TCM (proceed to Procedure 2).



PROCEDURE

Hide 1.INPUT TRANSAXLE COMPENSATION CODE INTO TCM (Procedure 1)

NOTICE:

Transaxle compensation codes are unique, 60-digit alphanumeric values printed on a QR label on the transaxle. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.


a.
C133268
2.222,2.382 3.209,2.538 0.988,0.157 10 QR Code Label 2.398,1.279 3.259,1.778 0.861,0.499 10 Transaxle Compensation Code 1.053,0.246 2.041,0.403 0.988,0.157 10 QR Code Label 2.183,2.453 2.023,2.453 2.023,2.453 2.168,2.883 false

Record the transaxle compensation code specified on the QR label.

HINT:

The transaxle compensation code is imprinted on the QR label.



b.

Move the shift lever to N or P.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.

NOTICE:

Do not start the engine.



f.

Enter the following menus: Powertrain / ECT / Utility / A/T Code Registration.

Powertrain > ECT > Utility
Tester Display
A/T Code Registration
50005 235 204

g.

Select "Set Compensation Code".


h.

Register the compensation code.

i.

Press "Input".


ii.

Manually input the transaxle compensation code. The code is a 60-digit alphanumeric value printed on the QR label. After inputting the code, press "OK".



i.

Check that the compensation code displayed on the screen is correct by comparing it with the 60-digit alphanumeric value on the QR label.

NOTICE:

If an incorrect transaxle compensation code is input into the TCM, shift shock will occur.



j.

Press "NEXT" to set the compensation code to the TCM.

HINT:
·

If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause a registration failure. Check the wire harness and the DLC3 connection. If no problem is found, the TCM may be malfunctioning. Check the TCM and repeat this operation.




k.

Press "EXIT".


Hide 2.TRANSFER TRANSAXLE COMPENSATION CODE (Procedure 2)

NOTICE:

Transaxle compensation codes are 60-digit alphanumeric values imprinted on a QR label on the transaxle. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.


HINT:

The following operation is available for use with TCMs that can transmit the registered transaxle compensation code to intelligent tester.


a.

Move the shift lever to N or P.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.

NOTICE:

Do not start the engine.


HINT:

The transaxle compensation code is imprinted on the QR label.



e.

Read the transaxle compensation code.

i.

Enter the following menus: Powertrain / ECT / Utility / A/T Code Registration.

Powertrain > ECT > Utility
Tester Display
A/T Code Registration
50005 235 204

ii.

Select "Read Compensation Code".


iii.

Press "Save".


iv.

Press "Save" or "Overwrite".

HINT:

Press "Overwrite".


NOTICE:

Do not use the code specified on the transaxle QR label even if the transaxle compensation code cannot be read using the intelligent tester. The code printed on an in-service transaxle may not match its current characteristics. Replace the TCM with a new one and perform a road test to allow the TCM to learn.



v.

Press "EXIT".


vi.

Turn the ignition switch off.



f.

Replace the TCM.


g.

Set the transaxle compensation code.

i.

Turn the ignition switch to ON.


ii.

Turn the intelligent tester on.


iii.

Enter the following menus: Powertrain / ECT / Utility / A/T Code Registration.

Powertrain > ECT > Utility
Tester Display
A/T Code Registration
50005 235 204

iv.

Select "Set Compensation Code".


v.

Press "Open".


vi.

Press "Open" again to proceed.


vii.

Press "Exit".