Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0076716 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E229630E05
2.781,0.573 2.875,0.719 0.094,0.146 10 false 5 2.74,0.76 2.927,0.906 0.188,0.146 10 false z3 3.792,0.573 3.969,0.719 0.177,0.146 10 false 13 3.771,0.76 4,0.906 0.229,0.146 10 false I28 3.208,0.677 3.5,0.823 0.292,0.146 10 false IL+2 2.781,1.323 2.875,1.469 0.094,0.146 10 false 3 2.74,1.51 2.927,1.656 0.188,0.146 10 false z3 3.792,1.323 3.969,1.469 0.177,0.146 10 false 11 3.771,1.51 3.99,1.656 0.219,0.146 10 false I28 3.219,1.427 3.479,1.573 0.26,0.146 10 false -DP 2.896,1.917 3.833,2.323 0.938,0.406 10 false Spiral Cable Sub-assembly 0.896,1.094 1.094,1.24 0.198,0.146 10 false LH 0.896,1.854 1.115,2 0.219,0.146 10 false RH 0.396,2.521 2.354,2.771 1.958,0.25 10 false Steering Pad Switch Assembly 0.396,3.479 1.292,3.74 0.896,0.26 10 false from Battery 2.563,4.177 2.875,4.323 0.313,0.146 10 false TAIL 3.438,3.635 3.917,3.781 0.479,0.146 10 false PANEL 4.438,3.896 5.615,4.135 1.177,0.24 10 false to Main Body ECU 5.729,4.625 7,5.021 1.271,0.396 10 false Radio and Display Receiver Assembly 6.021,0.75 6.313,0.896 0.292,0.146 10 false ILL+ 5.74,4.49 6.031,4.635 0.292,0.146 10 false I152 5.76,0.656 5.938,0.802 0.177,0.146 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I28-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the steering pad switch assembly connector (for 3 Spoke).


b.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

E245541C01
2.583,0.813 2.917,1.052 0.333,0.24 4.031,1.135 3.719,0.875 false 3.5,0.854 3.073,0.573 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 2.823,0.448 3.26,0.74 0.438,0.292 10 false -DP 4.083,1.052 4.521,1.344 0.438,0.292 10 false IL+2 2.688,0.844 3.125,1.135 0.438,0.292 10 false z3
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



c.

Disconnect the steering pad switch assembly connector (for 4 Spoke).


d.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

E245542C01
4.208,1.26 4.542,1.5 0.333,0.24 4.323,0.833 4,0.406 false 4.854,1.146 4.531,0.854 false 4.313,1.292 4.625,1.49 0.313,0.198 10 false z3 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 4.906,1.094 5.448,1.406 0.542,0.313 10 false IL+2 3.854,0.229 4.396,0.542 0.542,0.313 10 false -DP
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



e.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.
E263757C15
1.344,0.677 1.677,0.906 0.333,0.229 0.427,3.865 0.76,4.094 0.333,0.229 1.781,1.021 2,0.583 false 2.24,0.583 2.542,0.969 false 1.042,4.26 1.302,3.76 false 1.792,4.24 1.521,3.76 false 0.24,0.188 0.625,0.479 0.385,0.292 10 false *a 1.177,0.25 1.563,0.542 0.385,0.292 10 false *b 0.354,3.563 0.74,3.854 0.385,0.292 10 false *c 1.552,1.052 2.167,1.25 0.615,0.198 10 false IL+2 2.5,1.021 2.885,1.26 0.385,0.24 10 false -DP 1.438,0.708 1.75,0.906 0.313,0.198 10 false z3 0.885,4.302 1.271,4.542 0.385,0.24 10 false -DP 1.646,4.26 2.26,4.458 0.615,0.198 10 false IL+2 0.51,3.896 0.969,4.094 0.458,0.198 10 false I28
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z3-3 (-DP) - I28-11 (-DP) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Always Below 3 Ω
z3-3 (-DP) - I28-11 (-DP) Always Below 3 Ω


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



HINT:



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I152-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR