Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0076716 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Speaker Circuit  


DESCRIPTION

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E226481E27
5.729,7.5 6.958,8.104 1.229,0.604 10 false Radio and Display Receiver Assembly 3.031,1.24 4.313,1.896 1.281,0.656 10 false Front No. 2 Speaker Assembly RH 5.531,0.75 5.635,0.906 0.104,0.156 10 false 1 4.542,0.854 4.646,1.01 0.104,0.156 10 false 4 4.552,1.719 4.656,1.875 0.104,0.156 10 false 2 2.292,0.844 2.396,1 0.104,0.156 10 false 3 2.302,1.719 2.406,1.875 0.104,0.156 10 false 1 2.469,0.833 2.573,0.99 0.104,0.156 10 false + 2.479,1.719 2.583,1.875 0.104,0.156 10 false - 4.094,1.719 4.531,1.875 0.438,0.156 10 false TWR- 4.083,2.823 4.521,2.979 0.438,0.156 10 false TWL+ 4.104,3.688 4.542,3.844 0.438,0.156 10 false TWL- 4.063,0.854 4.5,1.01 0.438,0.156 10 false TWR+ 5.458,0.948 5.76,1.104 0.302,0.156 10 false I152 3.042,1.063 3.302,1.219 0.26,0.156 10 false I83 0.438,1.302 1.719,1.958 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.438,1.135 0.698,1.292 0.26,0.156 10 false J5 3.021,3.188 4.302,3.844 1.281,0.656 10 false Front No. 2 Speaker Assembly LH 4.531,2.823 4.635,2.979 0.104,0.156 10 false 4 4.531,3.688 4.635,3.844 0.104,0.156 10 false 2 2.323,2.833 2.427,2.99 0.104,0.156 10 false 3 2.323,3.688 2.427,3.844 0.104,0.156 10 false 1 2.469,2.823 2.573,2.979 0.104,0.156 10 false + 2.469,3.688 2.573,3.844 0.104,0.156 10 false - 3.031,3.021 3.292,3.177 0.26,0.156 10 false I1 0.427,3.25 1.708,3.906 1.281,0.656 10 false Front No. 1 Speaker Assembly LH 0.427,3.083 0.688,3.24 0.26,0.156 10 false K5 0.792,5.052 1.698,5.708 0.906,0.656 10 false Rear Speaker Assembly RH 0.781,4.885 1.094,5.042 0.313,0.156 10 false O18 0.76,6.615 1.667,7.271 0.906,0.656 10 false Rear Speaker Assembly LH 0.75,6.448 1.042,6.604 0.292,0.156 10 false O21 5.458,1.813 5.76,1.969 0.302,0.156 10 false I152 5.458,2.917 5.76,3.073 0.302,0.156 10 false I152 5.458,3.792 5.76,3.948 0.302,0.156 10 false I152 5.458,4.844 5.76,5 0.302,0.156 10 false I153 5.458,5.469 5.76,5.625 0.302,0.156 10 false I153 5.458,6.354 5.76,6.51 0.302,0.156 10 false I153 5.458,6.99 5.75,7.146 0.292,0.156 10 false I153 5.833,0.948 6.125,1.104 0.292,0.156 10 false FR+ 5.833,1.823 6.094,1.979 0.26,0.156 10 false FR- 5.844,2.927 6.25,3.146 0.406,0.219 10 false FL+ 5.844,3.802 6.104,3.958 0.26,0.156 10 false FL- 5.844,4.854 6.146,5.01 0.302,0.156 10 false RR+ 5.844,5.49 6.125,5.646 0.281,0.156 10 false RR- 5.844,6.365 6.125,6.521 0.281,0.156 10 false RL+ 5.854,7.01 6.115,7.167 0.26,0.156 10 false RL- 5.542,6.802 5.646,6.958 0.104,0.156 10 false 6 5.542,6.167 5.646,6.323 0.104,0.156 10 false 2 5.542,5.271 5.646,5.427 0.104,0.156 10 false 3 5.531,4.646 5.635,4.802 0.104,0.156 10 false 1 5.552,3.594 5.656,3.75 0.104,0.156 10 false 6 5.542,2.729 5.729,2.927 0.188,0.198 10 false 2 5.563,1.635 5.667,1.792 0.104,0.156 10 false 5 1.781,1.052 1.885,1.208 0.104,0.156 10 false 1 1.792,1.729 1.896,1.885 0.104,0.156 10 false 2 1.802,3.031 1.906,3.188 0.104,0.156 10 false 1 1.792,3.688 1.896,3.844 0.104,0.156 10 false 2 1.771,4.823 1.875,4.979 0.104,0.156 10 false 1 1.781,5.51 1.885,5.667 0.104,0.156 10 false 2 1.792,6.344 1.896,6.5 0.104,0.156 10 false 1 1.792,7.01 1.896,7.167 0.104,0.156 10 false 2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Disconnect the connectors from the radio and display receiver assembly and speakers.


b.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-1 (FR+) - I83-4 (TWR+) Always Below 1 Ω
I152-5 (FR-) - I83-2 (TWR-) Always Below 1 Ω
I152-2 (FL+) - I1-4 (TWL+) Always Below 1 Ω
I152-6 (FL-) - I1-2 (TWL-) Always Below 1 Ω



c.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-3 (+) - J5-1 Always Below 1 Ω
I83-1 (-) - J5-2 Always Below 1 Ω
I1-3 (+) - K5-1 Always Below 1 Ω
I1-1 (-) - K5-2 Always Below 1 Ω



d.

Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I153-1 (RR+) - O18-1 Always Below 1 Ω
I153-3 (RR-) - O18-2 Always Below 1 Ω
I153-2 (RL+) - O21-1 Always Below 1 Ω
I153-6 (RL-) - O21-2 Always Below 1 Ω



e.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-1 (FR+) - Body ground Always 10 kΩ or higher
I152-5 (FR-) - Body ground Always 10 kΩ or higher
I152-2 (FL+) - Body ground Always 10 kΩ or higher
I152-6 (FL-) - Body ground Always 10 kΩ or higher
I153-1 (RR+) - Body ground Always 10 kΩ or higher
I153-3 (RR-) - Body ground Always 10 kΩ or higher
I153-2 (RL+) - Body ground Always 10 kΩ or higher
I153-6 (RL-) - Body ground Always 10 kΩ or higher



f.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-3 (+) - Body ground Always 10 kΩ or higher
I83-1 (-) - Body ground Always 10 kΩ or higher
I1-3 (+) - Body ground Always 10 kΩ or higher
I1-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
E219303C54
0.354,1.906 0.885,2.198 0.531,0.292 0.354,1.531 0.885,1.823 0.531,0.292 0.531,1.958 0.823,2.125 0.292,0.167 10 false K5 0.531,1.594 0.823,1.76 0.292,0.167 10 false J5 0.125,0.104 0.698,0.583 0.573,0.479 10 false *a 0.958,1.594 1.25,1.875 0.292,0.281 10 false *A 0.958,1.958 1.313,2.229 0.354,0.271 10 false *B
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 - J5-2 Always 3.2 to 4.8 Ω
K5-1 - K5-2 Always 3.2 to 4.8 Ω




Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
E226097C24
1.469,0.656 1.927,0.938 0.458,0.281 1.458,1 1.917,1.281 0.458,0.281 1.333,1.802 1.083,2.469 false 1.677,1.813 1.563,2.229 false 2.302,1.813 2.417,2.229 false 1.99,1.802 2.167,2.469 false 0.094,0.083 0.708,0.521 0.615,0.438 10 false *a 1.958,0.729 2.438,1.073 0.479,0.344 10 false *A 1.958,1.063 2.396,1.375 0.438,0.313 10 false *B 1.604,0.719 2.073,1 0.469,0.281 10 false I83 1.646,1.063 2.208,1.458 0.563,0.396 10 false I1 1.5,2.24 1.823,2.583 0.323,0.344 10 false + 0.656,2.51 1.521,2.781 0.865,0.271 10 false TWR+*A 0.656,2.688 1.49,2.917 0.833,0.229 10 false TWL+*B 1.844,2.51 2.646,2.823 0.802,0.313 10 false TWR-*A 1.844,2.688 2.635,2.99 0.792,0.302 10 false TWL-*B 2.417,2.208 2.698,2.5 0.281,0.292 10 false -
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-2 (TWR-) - I83-4 (TWR+) Always 10 kΩ or higher
I83-1 (-) - I83-2 (TWR-) Always Below 1 Ω
I83-3 (+) - I83-4 (TWR+) Always Below 1 Ω
I1-2 (TWL-) - I1-4 (TWL+) Always 10 kΩ or higher
I1-1 (-) - I1-2 (TWL-) Always Below 1 Ω
I1-3 (+) - I1-4 (TWL+) Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

5.INSPECT REAR SPEAKER ASSEMBLY
5.INSPECT REAR SPEAKER ASSEMBLY
a.
E219303C55
0.469,1.917 1,2.208 0.531,0.292 0.469,1.542 1,1.833 0.531,0.292 0.573,1.969 1.188,2.375 0.615,0.406 10 false O21 0.573,1.604 1.25,2.01 0.677,0.406 10 false O18 0.146,0.073 0.563,0.438 0.417,0.365 10 false *a 1.073,1.594 1.448,1.896 0.375,0.302 10 false *A 1.073,1.979 1.458,2.229 0.385,0.25 10 false *B
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O18-1 - O18-2 Always 3.2 to 4.8 Ω
O21-1 - O21-2 Always 3.2 to 4.8 Ω




Result:
Proceed to
OK
NG



OK

NG