Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0076716 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the radio and display receiver assembly.



b.

Check for noise

i.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




Result:
Proceed to
OK
NG



OK

4.CHECK WINDOW GLASS ANTENNA WIRE

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK WINDOW GLASS ANTENNA WIRE
a.
E111994C17
0.432,0.608 0.62,0.765 0.188,0.156 10 *a 0.946,1.965 1.141,2.114 0.195,0.149 10 *b 2.178,1.735 2.366,1.885 0.188,0.149 10 *c 0.528,0.797 0.602,1.13 false 0.97,1.623 1.044,1.956 false 2.192,1.375 2.266,1.708 false
*a Tester Probe
*b Antenna Wire
*c Tin Foil


Check for continuity in the window glass antenna wire.

HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.



Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the radio and display receiver assembly connector.


b.
E188455C17
0.479,0.958 1.01,1.25 0.531,0.292 1.542,1.094 1.135,1.448 false 0.094,0.052 0.625,0.385 0.531,0.333 10 false *a 0.625,1.021 1.125,1.354 0.5,0.333 10 false RA 0.833,1.479 1.479,1.802 0.646,0.323 10 false ANT+
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

NORMAL OPERATION

NG

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the No. 2 antenna cord sub-assembly.


b.

Measure the resistance of the No. 2 antenna cord sub-assembly to check for an open circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

Below 1 Ω



c.

Measure the resistance between the No. 2 antenna cord sub-assembly and body ground to check for a short circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.REPLACE AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

NORMAL OPERATION

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY