Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0076716 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E229860E98
3.26,2.365 3.917,2.521 0.656,0.156 10 false (Shielded) 0.844,0.646 1.271,0.802 0.427,0.156 10 false UDO- 0.823,1.438 1.25,1.594 0.427,0.156 10 false UDO+ 0.854,2.229 1.26,2.385 0.406,0.156 10 false UJSS 5.729,1.323 5.854,1.479 0.125,0.156 10 false 3 5.729,0.542 5.844,0.698 0.115,0.156 10 false 2 5.729,2.115 5.854,2.271 0.125,0.156 10 false 5 1.323,0.531 1.5,0.688 0.177,0.156 10 false 2 1.323,1.323 1.5,1.479 0.177,0.156 10 false 3 1.323,2.115 1.5,2.271 0.177,0.156 10 false 5 0.344,2.667 0.698,2.823 0.354,0.156 10 false I146 5.531,2.625 5.927,2.781 0.396,0.156 10 false I156 0.344,2.844 1.542,3.24 1.198,0.396 10 false No. 1 Stereo Jack Adapter Assembly 5.531,2.802 6.771,3.146 1.24,0.344 10 false Radio and Display Receiver Assembly 5.917,0.635 6.438,0.792 0.521,0.156 10 false US1- 5.917,1.438 6.49,1.594 0.573,0.156 10 false US1+ 5.917,2.229 6.344,2.385 0.427,0.156 10 false USG1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the radio and display receiver assembly connector.


b.

Disconnect the No. 1 stereo jack adapter assembly connector.


c.
E226480C52
1.458,2.271 1.99,2.563 0.531,0.292 1.458,0.167 1.99,0.458 0.531,0.292 1.583,1.427 1.115,1.646 false 2.313,1.49 1.865,1.427 false 1.615,3.448 1,3.688 false 1.833,3.448 2.448,3.688 false 1.781,3.542 2.448,3.979 false 1.781,1.552 2.281,1.927 false 0.177,2.25 0.625,2.563 0.448,0.313 10 false *b 1.594,2.344 2.083,2.594 0.49,0.25 10 false I146 0.521,3.625 1.167,3.896 0.646,0.271 10 false UDO- 0.177,0.083 0.573,0.448 0.396,0.365 10 false *a 1.583,0.229 2.115,0.573 0.531,0.344 10 false I156 0.635,1.594 1.167,1.75 0.531,0.156 10 false US1+ 2.344,1.427 2.906,1.583 0.563,0.156 10 false US1- 2.469,3.635 3.25,4.083 0.781,0.448 10 false UDO+ 2.469,3.938 3.031,4.198 0.563,0.26 10 false UJSS 2.302,1.865 2.969,2.24 0.667,0.375 10 false USG1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I156-2 (US1-) - I146-2 (UDO-) Always Below 1 Ω
I156-3 (US1+) - I146-3 (UDO+) Always Below 1 Ω
I156-5 (USG1) - I146-5 (UJSS) Always Below 1 Ω
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR