Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM2030EQ _55 Steering _014656 STEERING COLUMN _0077044 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock ECU detects an IG2 power supply malfunction.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2788 IG2 Signal Malfunction Mismatch between the steering lock ECU IG2 input from the LIN communication system and from the direct line (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)).
·

ECU-IG2 NO. 3 fuse

·

Steering lock ECU (Steering lock actuator assembly)

·

Harness or connector


No confirmation operation is necessary (monitoring is continuous).

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C240290E15
5.375,1.448 5.688,1.635 0.313,0.188 10 IG2 5.375,0.635 5.688,0.823 0.313,0.188 10 LIN 5.375,2.229 5.781,2.417 0.406,0.188 10 GND 5.156,0.49 5.323,0.677 0.167,0.188 10 5 5.156,1.344 5.323,1.531 0.167,0.188 10 6 5.156,2.115 5.323,2.302 0.167,0.188 10 1 5.156,2.979 5.49,3.167 0.333,0.188 10 I24 5.156,3.146 6.969,3.51 1.813,0.365 10 Steering Lock ECU (Steering Lock Actuator Assembly) 0.125,2.958 0.458,3.146 0.333,0.188 10 I78 0.125,3.115 1.719,3.479 1.594,0.365 10 Certification ECU (Smart Key ECU Assembly) 2.781,3.333 4.375,3.531 1.594,0.198 10 LIN Communication Line 0.927,0.635 1.24,0.823 0.313,0.188 10 LIN 1.25,0.49 1.448,0.677 0.198,0.188 10 17 3.656,1.594 4.708,1.792 1.052,0.198 10 ECU-IG2 NO. 3 1.833,1.427 2.833,1.625 1,0.198 10 from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (POWER SOURCE MODE SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the I24 steering lock ECU connector.


c.
C157850C24
0.344,0.917 0.729,1.219 0.385,0.302 1.281,2.417 1.031,1.719 false 0.375,0.302 0.698,0.521 0.323,0.219 10 *a 0.458,0.99 0.865,1.292 0.406,0.302 10 I24 0.813,1.521 1.313,1.948 0.5,0.427 10 GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-1 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the I24 steering lock ECU connector.


e.
C157849C09
0.292,0.885 0.74,1.177 0.448,0.292 2.281,1.958 2.813,2.823 false 1.333,1.969 1.01,2.823 false 0.375,0.271 0.667,0.521 0.292,0.25 10 *a 0.438,0.948 0.813,1.198 0.375,0.25 10 I24 0.833,2.854 1.24,3.063 0.406,0.208 10 IG2 2.646,2.854 3.073,3.063 0.427,0.208 10 GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I24-6 (IG2) - I24-1 (GND) Engine switch on (IG) 11 to 14 V
I24-6 (IG2) - I24-1 (GND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR