Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM2030EQ _58 Vehicle Interior _014664 DOOR LOCK _0074587 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch (power window regulator master switch assembly), and driver door key cylinder or front passenger door key cylinder* switch signals from the front door lock with motor assembly (driver door). The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B294404E08
5.479,5.01 7.146,5.385 1.667,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.771,2.104 3.646,2.521 2.875,0.417 10 false Door Key Lock and Unlock Switch (Front Door Lock with Motor Assembly (Driver Door)) 0.771,4.448 3.052,4.875 2.281,0.427 10 false Door Control Switch (Power Window Regulator Master Switch Assembly) 1.26,1.365 1.51,1.615 0.25,0.25 10 false 7 2.208,1.625 2.531,1.854 0.323,0.229 10 false 10 2.229,1.073 2.49,1.344 0.26,0.271 10 false 9 1.26,3.604 1.51,3.823 0.25,0.219 10 false 1 2.229,3.292 2.479,3.552 0.25,0.26 10 false 9 2.229,3.854 2.531,4.156 0.302,0.302 10 false 2 5.719,0.958 6.01,1.188 0.292,0.229 10 false 11 5.719,1.521 6.01,1.729 0.292,0.208 10 false 24 5.75,3.771 5.99,3.938 0.24,0.167 10 false 9 5.719,3.198 6.115,3.479 0.396,0.281 10 false 10 1.948,3.302 2.302,3.583 0.354,0.281 10 false UL 2.031,4.073 2.281,4.292 0.25,0.219 10 false L 1.417,3.604 1.844,3.906 0.427,0.302 10 false E 1.958,1.813 2.406,2.083 0.448,0.271 10 false UL 2.052,1.073 2.313,1.323 0.26,0.25 10 false L 1.427,1.365 1.656,1.625 0.229,0.26 10 false E 6.042,1.177 6.406,1.531 0.365,0.354 10 false L2 6.042,1.729 6.448,2.052 0.406,0.323 10 false UL3 6.042,3.969 6.375,4.198 0.333,0.229 10 false L1 6.042,3.406 6.375,3.583 0.333,0.177 10 false UL1 5.708,3.958 6.115,4.188 0.406,0.229 10 false I13 5.719,3.396 6.115,3.667 0.396,0.271 10 false I13 5.719,1.708 6.083,1.948 0.365,0.24 10 false I13 5.719,1.146 6.104,1.417 0.385,0.271 10 false I13 0.781,4.271 1.219,4.563 0.438,0.292 10 false K10 0.781,1.948 1.24,2.24 0.458,0.292 10 false K1 0.146,0.156 0.979,0.521 0.833,0.365 12 false for LHD:

B294404E04
5.477,4.978 7.124,5.297 1.647,0.318 10 Main Body ECU (Multiplex Network Body ECU) 0.772,2.08 3.643,2.392 2.872,0.311 10 Door Key Lock and Unlock Switch (Front Door Lock with Motor Assembly (Driver Door)) 0.772,4.416 3.046,4.738 2.274,0.323 10 Door Control Switch (Power Window Regulator Master Switch Assembly) 1.265,1.343 1.368,1.483 0.103,0.14 10 8 2.225,1.605 2.338,1.745 0.112,0.14 10 5 2.225,1.059 2.335,1.199 0.11,0.14 10 6 1.265,3.591 1.368,3.731 0.103,0.14 10 9 2.225,3.308 2.332,3.448 0.106,0.14 10 8 2.225,3.854 2.335,3.994 0.11,0.14 10 2 5.736,0.923 5.913,1.064 0.177,0.14 10 11 5.736,1.498 5.913,1.638 0.177,0.14 10 24 5.771,3.761 5.878,3.901 0.106,0.14 10 9 5.728,3.2 5.921,3.34 0.193,0.14 10 10 1.949,3.257 2.165,3.4 0.216,0.142 10 UL 2.033,4.042 2.152,4.184 0.119,0.142 10 L 1.421,3.594 1.54,3.736 0.119,0.142 10 E 1.958,1.786 2.175,1.929 0.216,0.142 10 UL 2.052,0.997 2.171,1.139 0.119,0.142 10 L 1.43,1.338 1.55,1.48 0.119,0.142 10 E 6.037,1.148 6.214,1.288 0.177,0.14 10 L2 6.037,1.708 6.311,1.848 0.274,0.14 10 UL3 6.037,3.964 6.214,4.104 0.177,0.14 10 L1 6.037,3.403 6.311,3.543 0.274,0.14 10 UL1 5.716,3.954 5.944,4.094 0.229,0.14 10 I13 5.716,3.394 5.944,3.534 0.229,0.14 10 I13 5.716,1.699 5.944,1.839 0.229,0.14 10 I13 5.716,1.138 5.944,1.278 0.229,0.14 10 I13 0.778,4.242 1.047,4.382 0.27,0.14 10 J10 0.778,1.902 0.955,2.042 0.177,0.14 10 J1 0.103,0.036 0.773,0.22 0.67,0.184 12 for RHD:

PROCEDURE

1.CHECK DOOR LOCK OPERATION

Result:
Result Proceed to
All doors cannot be locked through door control switch (power window regulator switch assembly) A
All doors cannot be locked through door key cylinder B



A

2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))

B

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)))
2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18
OK:

The intelligent tester indicates ON or OFF according to the switch operation shown in the table above.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.
B279066C01
1.594,3.219 1.594,2.552 1.594,2.552 1.781,2.552 false 1.458,3.219 1.458,2.24 1.458,2.24 1.781,2.24 false 0.479,3.219 0.479,2.24 0.479,2.24 0.604,2.24 false 1.844,2.469 2.052,2.656 0.208,0.188 10 false E 1.844,2.167 2.156,2.427 0.313,0.26 10 false L 0.656,2.167 1.083,2.385 0.427,0.219 10 false UL 0.156,0.104 0.302,0.271 0.146,0.167 10 false *a
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
2 (L) - 1 (E) off 10 kΩ or higher
9 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
9 (UL) - 1 (E) off 10 kΩ or higher




b.

for RHD

i.
B295736C04
0.148,0.115 0.323,0.271 0.175,0.156 10 *a 0.469,3.214 0.469,1.959 0.469,1.959 0.787,1.959 false 0.604,3.227 0.604,2.482 0.604,2.482 0.784,2.482 false 1.448,3.228 1.448,2.483 1.448,2.483 1.689,2.483 false 0.823,2.406 1.028,2.549 0.205,0.142 10 UL 0.832,1.873 0.946,2.016 0.115,0.142 10 E 1.734,2.398 1.836,2.54 0.102,0.142 10 L
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 9 (E) Lock switch pushed Below 1 Ω
2 (L) - 9 (E) off 10 kΩ or higher
8 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 9 (E) off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K10-2 (L) - I13-9 (L1) Always Below 1 Ω
K10-9 (UL) - I13-10 (UL1) Always Below 1 Ω
K10-1 (E) - Body ground Always Below 1 Ω
K10-2 (L) - Body ground Always 10 kΩ or higher
K10-9 (UL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J10-2 (L) - I13-9 (L1) Always Below 1 Ω
J10-8 (UL) - I13-10 (UL1) Always Below 1 Ω
J10-9 (E) - Body ground Always Below 1 Ω
J10-2 (L) - Body ground Always 10 kΩ or higher
J10-8 (UL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal ON or OFF ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position
-
D Door Key SW-UL Driver door key-linked lock/unlock switch unlock signal ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-
Body Electrical > Main Body > Data List
Tester Display
Door Key SW-Lock
D Door Key SW-UL
50003 123 19,21
OK:

The intelligent tester indicates ON or OFF according to the key cylinder operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)
6.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)
a.

Remove the front door lock with motor assembly (driver door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.
B280166C01
0.101,0.076 0.267,0.242 0.166,0.166 10 *a 2.851,1.623 3.017,1.789 0.166,0.166 10 *b 3.057,0.558 3.223,0.723 0.166,0.166 10 *c 2.273,3.437 2.273,3.802 2.273,3.802 2.086,3.802 false 2.427,3.437 2.427,4.115 2.427,4.115 1.931,4.115 false 2.737,3.437 2.737,4.436 2.737,4.436 2.086,4.436 false 1.927,4.36 2.042,4.503 0.115,0.142 10 E 1.807,4.034 1.908,4.176 0.101,0.142 10 L 1.816,3.716 2.027,3.858 0.212,0.142 10 UL
*a Component without harness connected
(Front Door Lock with Motor Assembly (Driver Door))
*b Lock
*c Unlock


for LHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Held to lock side Below 1 Ω
9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher
10 (UL) - 7 (E) Held to unlock side Below 1 Ω
10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher




c.
B284859C05
0.748,3.424 0.748,4.442 0.748,4.442 0.903,4.442 false 1.057,3.424 1.057,4.133 1.057,4.133 1.212,4.133 false 1.212,3.424 1.212,3.823 1.212,3.823 1.367,3.823 false 0.955,4.35 1.079,4.507 0.124,0.156 10 E 1.264,4.041 1.374,4.197 0.11,0.156 10 L 1.402,3.732 1.614,3.888 0.212,0.156 10 UL 0.084,0.033 0.233,0.204 0.149,0.17 10 *a 0.6,1.615 0.749,1.785 0.149,0.17 10 *b 0.342,0.515 0.491,0.685 0.149,0.17 10 *c
*a Component without harness connected
(Front Door Lock with Motor Assembly (Driver Door))
*b Lock
*c Unlock


for RHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K1-9 (L) - I13-11 (L2) Always Below 1 Ω
K1-10 (UL) - I13-24 (UL3) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
I13-11 (L2) - Body ground Always 10 kΩ or higher
I13-24 (UL3) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J1-6 (L) - I13-11 (L2) Always Below 1 Ω
J1-5 (UL) - I13-24 (UL3) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
I13-11 (L2) - Body ground Always 10 kΩ or higher
I13-24 (UL3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR