Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014664 DOOR LOCK _0074590 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

B312366E02
6.115,1.865 6.635,2.188 0.521,0.323 10 false CAN 5.104,1.865 5.563,2.146 0.458,0.281 10 false CAN 4.375,1.823 4.917,2.115 0.542,0.292 10 false FRCY 4.375,0.708 4.938,1.167 0.563,0.458 10 false KSW 2.146,0.615 2.24,0.76 0.094,0.146 10 false 1 2.156,1.719 2.25,1.865 0.094,0.146 10 false 1 1.333,0.615 1.76,0.958 0.427,0.344 10 false 2 0.906,3.458 2.667,3.604 1.76,0.146 10 false : CAN Communication Line 0.708,2.125 2.844,2.438 2.135,0.313 10 false Front Door Courtesy Light Switch Assembly (for Driver Door) 1.042,1 2.51,1.313 1.469,0.313 10 false Unlock Warning Switch Assembly 4.333,2.708 5.521,3.313 1.188,0.604 10 false Main Body ECU (Multiplex Network Body ECU) 5.927,2.594 7.125,2.906 1.198,0.313 10 false Combination Meter Assembly 4.146,0.573 4.552,1.094 0.406,0.521 10 false 17 4.146,1.698 4.438,1.927 0.292,0.229 10 false 19 4.333,2.552 4.677,2.74 0.344,0.188 10 false I13 1.042,0.823 1.573,1.094 0.531,0.271 10 false I33 0.708,1.938 1,2.083 0.292,0.146 10 false O10

CAUTION / NOTICE / HINT

NOTICE:

Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the How to Proceed with Troubleshooting procedure (Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Then, conduct the following procedure.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Check the seat belt warning buzzer operation.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION

HINT:

The key reminder warning system sounds the buzzer built into the combination meter assembly as a key reminder warning. This buzzer is also used for the seat belt warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the seat belt is not fastened.


OK:

Combination meter buzzer sounds.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Select FL Door Courtesy in the Data List and read the intelligent tester display.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch LH signal ON or OFF ON: Front door LH open
OFF: Front door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

ON or OFF appears on the screen according to the driver door condition.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH ASSEMBLY)

NG

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for DRIVER DOOR)
3.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Select Key Unlock Warning SW in the Data List and read the intelligent tester display.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal ON or OFF ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

ON or OFF appears on the screen according to whether the key is in the ignition key cylinder.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
B203483C02
0.063,0.052 0.438,0.26 0.375,0.208 10 *a
*a Component without harness connected
(Unlock Warning Switch Assembly)


Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch free (Key removed) 10 kΩ or higher
1 - 2 Switch pushed (Key set) Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I33-1 - I13-17 (KSW) Always Below 1 Ω
I33-2 - Body ground Always Below 1 Ω
I33-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for DRIVER DOOR)
a.
B203492C04
1.188,1.26 1.188,1.708 1.188,1.708 1.406,1.708 false 0.104,0.104 0.792,0.469 0.688,0.365 10 *a 1.427,1.635 1.75,1.917 0.323,0.281 10 *1
*1 Switch Body
*a Component without harness connected
(Front Door Courtesy Light Switch Assembly (for Driver door))


Remove the front door courtesy light switch assembly (for driver door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Switch body Courtesy switch pushed (Door closed) 10 kΩ or higher
1 - Switch body Courtesy switch free (Door open) Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for DRIVER DOOR)

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O10-1 - I13-2 (FRCY) Always Below 1 Ω
O10-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR