Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014666 LIGHTING (INT) _0074614 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E239243E04
0.406,0.667 1.281,0.885 0.875,0.219 10 false from Battery 0.146,1.156 1.229,1.771 1.083,0.615 10 false from Certification ECU*1 or Ignition Switch*2 3.448,2.458 6.146,2.635 2.698,0.177 10 false Instrument Panel Junction Block Assembly 5.479,2.896 7.135,3.26 1.656,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 3.698,0.469 3.865,0.615 0.167,0.146 10 false 1 3.583,0.677 3.917,0.823 0.333,0.146 10 false 3E*4 3.208,0.948 3.427,1.094 0.219,0.146 10 false 23 3.188,1.146 3.385,1.292 0.198,0.146 10 false 3B 4.115,1.469 4.875,1.615 0.76,0.146 10 false ACC NO. 1 4.927,0.833 5.698,0.979 0.771,0.146 10 false ECU-ACC 6.281,0.688 6.667,0.844 0.385,0.156 10 false ACC 3.24,1.74 3.406,1.885 0.167,0.146 10 false 7 3.188,1.917 3.448,2.083 0.26,0.167 10 false 3B 5.896,0.469 6.135,0.615 0.24,0.146 10 false 29 5.875,0.667 6.167,0.833 0.292,0.167 10 false MB 2.01,0.813 2.365,1.042 0.354,0.229 10 false ALT 0.146,2.51 2.646,2.719 2.5,0.208 10 false *1: w/ Smart Entry and Start System 0.146,2.802 2.677,3.01 2.531,0.208 10 false *2: w/o Smart Entry and Start System 3.25,0.469 3.417,0.615 0.167,0.146 10 false 1 3.135,0.677 3.531,0.823 0.396,0.146 10 false 3F*3 0.146,3.094 1.042,3.302 0.896,0.208 10 false *3: for RHD 0.146,3.385 1.052,3.594 0.906,0.208 10 false *4: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
-
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the 3F*1, 3E*2 and 3B instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground*1 Ignition switch off 11 to 14 V
3E-1 - Body ground*2 Ignition switch off 11 to 14 V
3B-23 - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-7 - Body ground Always Below 1 Ω


*1: for RHD

*2: for LHD



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC NO. 1 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E191508C05
4.969,0.552 5.302,0.76 0.333,0.208 3.469,2.375 3.802,2.583 0.333,0.208 1.188,0.677 1.521,0.885 0.333,0.208 1.771,0.677 2.104,0.885 0.333,0.208 5.083,2.99 5.229,3.427 false 5.052,0.573 5.313,0.729 0.26,0.156 10 false 3B 3.542,2.396 3.823,2.563 0.281,0.167 10 false MB 0.677,0.229 0.865,0.375 0.188,0.146 10 false *a 5.177,3.438 5.583,3.625 0.406,0.188 10 false ACC 1.281,0.698 1.469,0.844 0.188,0.146 10 false 3F 1.573,0.708 1.813,0.854 0.24,0.146 10 false *A 1.854,0.698 2.042,0.844 0.188,0.146 10 false 3E 2.156,0.708 2.344,0.854 0.188,0.146 10 false *B
*A for RHD *B for LHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3F-1 - MB-29 (ACC)*1 Always 10 kΩ or higher
3F-1 - MB-29 (ACC)*1 Battery positive (+) → 3B-23
Battery negative (-) → 3B-7
Below 1 Ω
3E-1 - MB-29 (ACC)*2 Always 10 kΩ or higher
3E-1 - MB-29 (ACC)*2 Battery positive (+) → 3B-23
Battery negative (-) → 3B-7
Below 1 Ω


*1: for RHD

*2: for LHD



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY