This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1500 | Fuel Sender Open Detected | When IG voltage is 9.5 V or more and the following condition is detected:
1.
Fuel sender gauge operation malfunction |
·
Harness or connector ·
Fuel sender gauge assembly ·
Combination meter assembly |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input signal | Min.: 0 , Max. 127.5 | Fuel receiver gauge indicates F: 62.9
Fuel receiver gauge indicates 3/4: 54.5 Fuel receiver gauge indicates 1/2: 35.0 Fuel receiver gauge indicates 1/4: 15.4 Fuel receiver gauge indicates E: 7.0 |
Unit: Liter |
| Tester Display |
|---|
| Fuel Input |
| Result | Proceed to |
|---|---|
| Fuel level data can be displayed on the intelligent tester and DTC B1500 is output. | A |
| Fuel level data cannot be displayed on the intelligent tester. | B |
A
B
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the I18 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-18 (FR) - I18-17 (FE) | Always | 13.5 to 414.5 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N11 fuel suction tube assembly with pump and gauge connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-18 (FR) - N11-2 (FS) | Always | Below 1 Ω |
| I18-18 (FR) - Body ground | Always | 10 kΩ or higher |
| I18-17 (FE) - N11-3 (FE) | Always | Below 1 Ω |
| I18-17 (FE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Fuel Sender Gauge Assembly) |
Remove the fuel sender gauge assembly.
See pageEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Check that the float moves smoothly between E and F.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Float level is F (upper) | 13.5 to 16.5 Ω |
| 1 - 2 | Float level is between F (upper) and E (lower) | 13.5 to 414.5 Ω (Gradually changes) |
| 1 - 2 | Float level is E (lower) | 405.5 to 414.5 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.
There is no deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG