These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1507 | Open in Turn Signal Circuit | When IG voltage is 9.5 V or more and the following condition is detected:
1.
Open in turn signal light circuit |
·
Harness or connector ·
Bulb ·
Instrument panel junction block assembly ·
Combination meter assembly |
| B1508 | Short in Turn Signal / Hazard Flasher Circuit | When IG voltage is 9.5 V or more and the following condition is detected:
1.
Short in turn signal light circuit or hazard warning light circuit |
·
Harness or connector ·
Bulb ·
Instrument panel junction block assembly ·
Combination meter assembly |
1. w/o Seat Position Memory
2. w/ Seat Position Memory
Inspect the bulbs for this system before performing the following procedure.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| Turn signal lights for one side do not illuminate. | A |
| Front turn signal light does not illuminate. | B |
| Rear turn signal light does not illuminate. | C |
| Side turn signal light does not illuminate. (w/o Seat Position Memory) | D |
| Side turn signal light does not illuminate. (w/ Seat Position Memory) | E |
A
B
C
D
E
Disconnect the I17 combination meter assembly connector.
Disconnect the 3A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-7 (LL) - 3A-20 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-13 (LR) - 3A-37 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-7 (LL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-13 (LR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the A65*1 or A23*2 headlight assembly connector.
*1: for RH
*2: for LH
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A65-2 (B)*1 - 3D-5 | Always | Below 1 Ω |
| A65-1 (E)*1 - Body ground | Always | Below 1 Ω |
| A23-2 (B)*2 - 3D-10 | Always | Below 1 Ω |
| A23-1 (E)*2 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A65-2 (B)*1 - Body ground | Always | 10 kΩ or higher |
| A23-2 (B)*2 - Body ground | Always | 10 kΩ or higher |
*1: for RH
*2: for LH
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the T13*1 or T8*2 rear combination light assembly connector.
*1: for RH
*2: for LH
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-1 (B) - 3C-22 | Always | Below 1 Ω |
| T8-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T13-1 (B) - 3C-19 | Always | Below 1 Ω |
| T13-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-1 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T13-1 (B) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the J14*1 or K13*2 outer rear view mirror assembly connector.
*1: for RH
*2: for LH
Disconnect the 3A and 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K13-2 (B) - 3A-40 | Always | Below 1 Ω |
| K13-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-2 (B) - 3B-32 | Always | Below 1 Ω |
| J14-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K13-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-2 (B) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-37 - 3D-5 | Always | Below 1 Ω |
| 3A-37 - 3C-19 | Always | Below 1 Ω |
| 3A-20 - 3D-10 | Always | Below 1 Ω |
| 3A-20 - 3C-22 | Always | Below 1 Ω |
| 3A-37 - 3B-32 | Always | Below 1 Ω |
| 3A-20 - 3A-40 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J13*1 or K12*2 outer mirror control ECU assembly connector.
*1: for RH
*2: for LH
Disconnect the 3A and 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K12-11 (TRNI) - 3A-40 | Always | Below 1 Ω |
| K12-7 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J13-11 (TRNI) - 3B-32 | Always | Below 1 Ω |
| J13-7 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K12-11 (TRNI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J13-11 (TRNI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly with a new or a known good one.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
Recheck for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B