Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2030EQ _58 Vehicle Interior _014667 METER / GAUGE / DISPLAY _0074615 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the meter ECU receives engine speed signals from the ECM using the CAN communication system. The meter ECU displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E143765E85
0.625,3.083 2.021,3.417 1.396,0.333 10 false ECM 2.927,3.156 3.021,3.344 0.094,0.188 10 false : 3.01,3.177 4.656,3.531 1.646,0.354 10 false CAN Communication Line 5.302,3.073 7.115,3.677 1.813,0.604 10 false Combination Meter Assembly (Meter Circuit Plate)

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TACHO METER OPERATION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TACHO METER OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TachoMeter Operation Tachometer 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 (rpm) -
Body Electrical > Combination Meter > Active Test
Tester Display
TachoMeter Operation
50004 122 2
OK:

Tachometer indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK SFI SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK SFI SYSTEM
a.

Check if SFI system DTCs are output.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED, ENGINE RPM)

B

4.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED, ENGINE RPM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

i.

for Engine and ECT: Powertrain / Engine and ECT / Data List.


ii.

for Combination Meter: Body / Combination Meter / Data List.



e.

Check the values by referring to the table below.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm
·

600 to 700 rpm: Idling


Results of real-vehicle check:
Idling (warm up the engine and A/C off): 660 rpm
·

Stored as Freeze Frame Data

·

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.


Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Rpm Engine Speed Min.: 0 rpm, Max.: 12750 rpm 600 to 700 rpm: Idling -
Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9
Body Electrical > Combination Meter > Data List
Tester Display
Engine Rpm
50003 122 9

Result:
Result Proceed to
The data list values of the ECUs match. A
The data list values of the ECUs do not match. B


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.




A

REPLACE COMBINATION METER ASSEMBLY

B