Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.02–2015.04
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C238830C02
0.209,0.168 0.407,0.339 0.198,0.17 10 *a
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


Terminal No. (Symbol) Terminal Description
1 (+BM) ABS motor relay power supply
2 (SP1) Speed signal output for speedometer
3 - (Not used)
4 (FR-) Front wheel speed RH (-) signal input
5 - (Not used)
6 - (Not used)
7 - (Not used)
8 (FL-) Front wheel speed LH (-) signal input
9 - (Not used)
10 - (Not used)
11 - (Not used)
12 - (Not used)
13 (GND2) Pump motor ground
14 (CANL) CAN communication line L
15 - (Not used)
16 (FR+) Front wheel speed RH (+) signal input
17 (RR+) Rear wheel speed RH (+) signal input
18 (RL-) Rear wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) signal input
20 - (Not used)
21 - (Not used)
22 - (Not used)
23 - (Not used)
24 - (Not used)
25 (+BS) ABS solenoid relay power supply
26 (CANH) CAN communication line H
27 - (Not used)
28 (IG1) IG1 power source input
29 (RR-) Rear wheel speed RH (-) signal input
30 (STP) Stop light switch input
31 (RL+) Rear wheel speed LH (+) signal input
32 - (Not used)
33 - (Not used)
34 (FSW+) Brake pedal load sensing switch input
35 - (Not used)
36 - (Not used)
37 - (Not used)
38 (GND1) Skid control ECU ground


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage and resistance on the wire harness side.

C238831C02
0.216,0.14 0.442,0.345 0.226,0.205 10 *a 1.519,0.673 1.94,0.939 0.42,0.266 1.596,0.736 1.905,0.892 0.309,0.156 10 A49
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -


HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) because the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A49-1 (+BM) - Body ground G - Body ground ABS motor relay power supply Always 11 to 14 V
A49-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A49-25 (+BS) - Body ground L - Body ground ABS solenoid relay power supply Always 11 to 14 V
A49-28 (IG1) - Body ground V - Body ground IG1 power source input Ignition switch ON 11 to 14 V
A49-30 (STP) - Body ground GR - Body ground Stop light switch input Stop light switch ON → OFF (Brake pedal depressed → released) 11 to 14 V* → Below 1.5 V
A49-34 (FSW+) - Body ground L - Body ground Brake pedal load sensing switch input Brake pedal load sensing switch OFF → ON (Brake pedal depressed → released) 950 to 1050 Ω → 203 to 223 Ω
A49-38 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.