Home › Vehicle Exterior › LIGHTING (EXT) › AFS (ADAPTIVE FRONT-LIGHTING SYSTEM) › 2012.02–2015.04
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0074739 AFS (ADAPTIVE FRONT-LIGHTING SYSTEM) U

LIGHTING (EXT)  AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / AFS / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > AFS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
AFS OFF Switch AFS OFF switch signal ON or OFF ON: AFS off
OFF: AFS on
-
Traveling Direction Traveling Direction Not Fwd or Fwd Not Fwd: Shift lever in R or N
Fwd: Shift lever not in R or N
-
Headlight Low Beam State Low beam headlight state ON or OFF ON: Low beam headlights on
OFF: Low beam headlights off
-
Headlight High Beam State High beam headlight state ON or OFF ON: High beam headlights on
OFF: High beam headlights off
-
Engine Engine condition Run or Stop Run: Engine running
Stop: Engine stopped
-
+B IG power supply voltage value 0.00 to 19.75 V 11 to 14 V -
Height Sens Pw Supply Val Height control sensor power supply value 0.00 to 6.25 V Approx. 5 V -
Rr Height Sens Signal Val Rear height control sensor signal value 0.00 to 5.00 V Approx. 2.5 V (When vehicle is level) Value changes according to vehicle height
Steering Sens Signal Steering angle sensor signal value -384.0 deg to 382.5 deg Approx. 0 deg (When steering wheel is straight) Value changes according to steering wheel position
Steering Sens Center Pos Steering angle sensor center position -3072.0 deg to 3070.5 deg Condition can be displayed -
FR Wheel Speed Front right wheel speed 0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -
FL Wheel Speed Front left wheel speed 0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -
Vehicle Speed Vehicle speed 0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -
Rear Height Adjust Valid Flag Rear height adjustment range Valid or Invalid Condition can be displayed -
Init Writing Count Number of times for initialization 0 to 255 Condition can be displayed -
Sensor Initialization Hist Sensor Initialization History not comp, 10%, 25%, 50%, 75%, 100% or complied Condition can be displayed -
L Swivel Target Step Swivel motor LH target step value 0 to 400 step 34 to 286 step -
L Swivel Current Step Swivel motor LH current step value 0 to 400 step 34 to 286 step -
R Swivel Target Step Swivel motor RH target step value 0 to 400 step 8 to 185 step -
R Swivel Current Step Swivel motor RH current step value 0 to 400 step 8 to 185 step -
LR Leveling Target Step Leveling motor LH and RH target step value 0 to 300 step 5 to 247 step -
L Leveling Current Step Leveling motor LH current step value 0 to 300 step 5 to 247 step -
R Leveling Current Step Leveling motor RH current step value 0 to 300 step 5 to 247 step -
Number Of Trouble Codes Number of trouble codes 0 to 255 Condition can be displayed -


ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / AFS / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > AFS > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Drive The Leveling Motor Leveling motor operation Up/Down/Stop Perform the active test with the engine started and vehicle stopped.
Drive Swivel Motor LH Swivel motor LH direction rotation Left/Right/Stop Perform the active test with the engine started and vehicle stopped.
Drive Swivel Motor RH Swivel motor RH direction rotation Left/Right/Stop Perform the active test with the engine started and vehicle stopped.
AFS OFF Indicator AFS OFF indicator ON/OFF -