These DTCs are stored when the AFS ECU (headlight swivel ECU assembly) detects errors in its own communication with the headlight swivel motor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2410 | Headlight Swivel Motor LH Communication Malfunction | AFS ECU (headlight swivel ECU assembly) detected errors in its own communication with headlight swivel motor LH | ·
Headlight swivel motor LH ·
Harness or connector ·
AFS ECU (headlight swivel ECU assembly) |
| B2411 | Headlight Swivel Motor RH Communication Malfunction | AFS ECU (headlight swivel ECU assembly) detected errors in its own communication with headlight swivel motor RH | ·
Headlight swivel motor RH ·
Harness or connector ·
AFS ECU (headlight swivel ECU assembly) |
Inspect the fuses for circuits related to this system before performing the following procedure.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)>DTC CHECK / CLEAR
DTC B2410 or B2411 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to AFS ECU (Headlight Swivel ECU Assembly)) |
Disconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-14 (IGS) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to AFS ECU (Headlight Swivel ECU Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-22 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the LH side or RH side headlight unit connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-1 (SMBL) - A22-1 (SMBL) | Always | Below 1 Ω |
| A35-29 (SML) - A22-2 (SML) | Always | Below 1 Ω |
| A35-23 (SMGL) - A22-3 (SMGL) | Always | Below 1 Ω |
| A35-1 (SMBL) - Body ground | Always | 10 kΩ or higher |
| A35-29 (SML) - Body ground | Always | 10 kΩ or higher |
| A35-23 (SMGL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (SMBR) - A67-1 (SMBR) | Always | Below 1 Ω |
| A35-10 (SMR) - A67-2 (SMR) | Always | Below 1 Ω |
| A35-24 (SMGR) - A67-3 (SMGR) | Always | Below 1 Ω |
| A35-2 (SMBR) - Body ground | Always | 10 kΩ or higher |
| A35-10 (SMR) - Body ground | Always | 10 kΩ or higher |
| A35-24 (SMGR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(AFS ECU (Headlight Swivel ECU Assembly)) |
Reconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-1 (SMBL) - A35-23 (SMGL) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (SMBR) - A35-24 (SMGR) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight unit with a new or a known good one.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)>DTC CHECK / CLEAR
DTC B2410 or B2411 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG