Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074575 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
·

Power window regulator motor assembly (for driver side)

·

Sliding roof ECU (sliding roof drive gear sub-assembly)*

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector



*: w/ Sliding Roof System


WIRING DIAGRAM

B281954
0.333,3.448 3.333,3.823 3,0.375 10 false Instrument Panel Junction Block Assembly 0.51,1.896 2.156,2.552 1.646,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 4.417,1.521 7.01,2 2.594,0.479 10 false Power Window Regulator Motor Assembly (for Driver Side) 4.802,3.25 6.698,3.823 1.896,0.573 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)*3 0.75,4.323 2.615,4.583 1.865,0.26 10 false : LIN Communication Line 3.583,4.365 5.521,4.729 1.938,0.365 10 false *3: w/ Sliding Roof System 1.698,0.823 2.313,1.25 0.615,0.427 10 false LIN2 4.875,2.563 5.635,2.813 0.76,0.25 10 false MPX1 4.594,2.417 5.031,2.74 0.438,0.323 10 false 11 4.854,0.854 5.521,1.302 0.667,0.448 10 false LIN 4.646,0.688 5.125,1.01 0.479,0.323 10 false 9 2.563,0.708 3.292,1.344 0.729,0.635 10 false LIN2 2.938,0.708 3.385,1.208 0.448,0.5 10 false 30 2.094,0.708 2.396,0.927 0.302,0.219 10 false 16 0.51,1.729 1.125,2.073 0.615,0.344 10 false MB 0.323,3.292 0.917,3.594 0.594,0.302 10 false 3B 4.813,3.073 5.229,3.281 0.417,0.208 10 false S4 4.438,1.375 5.229,1.708 0.792,0.333 10 false K9*1, J9*2 3.583,4.083 5.521,4.448 1.938,0.365 10 false *2: for RHD 3.583,3.781 5.521,4.146 1.938,0.365 10 false *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

·

When the power window regulator motor assembly (for driver side) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the intelligent tester to troubleshoot with the ignition switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B281983
1.813,0.917 2.177,1.188 0.365,0.271 5.49,0.844 5.854,1.115 0.365,0.271 1.802,2.188 2.052,1.74 false 5.615,2.271 5.865,1.833 false 1.896,0.969 2.208,1.167 0.313,0.198 10 MB 5.604,0.896 5.917,1.094 0.313,0.198 10 3B 0.406,0.375 0.719,0.573 0.313,0.198 10 *a 4.792,0.458 5.104,0.656 0.313,0.198 10 *b 1.667,2.219 2.281,2.417 0.615,0.198 10 LIN2 5.448,2.302 6.063,2.5 0.615,0.198 10 LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Instrument Panel Junction Block Assembly)



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3B-30 (LIN2) - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - EACH ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - EACH ECU)
a.

Disconnect the K9*1, J9*2 power window regulator motor (for driver side) connector.


b.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector*3.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-30 (LIN2) - K9-9 (LIN)*1
3B-30 (LIN2) - J9-9 (LIN)*2
Always Below 1 Ω
3B-30 (LIN2) - S4-11 (MPX1)*3 Always Below 1 Ω
K9-9 (LIN)*1 - Body ground
J9-9 (LIN)*2 - Body ground
Always 10 kΩ or higher
S4-11 (MPX1)*3 - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD

*3: w/ Sliding Roof System



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE))
a.

Reconnect the 3B instrument panel junction block assembly.


b.

Reconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector*.

*: w/ Sliding Roof System



c.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

4.CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)

4.CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Reconnect the K9*1, J9*2 power window regulator motor (for driver side) connector.


b.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector*3.


*1: for LHD

*2: for RHD

*3: w/ Sliding Roof System


c.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)