Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074575 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN
·

Errors in LIN communication between ECUs or an open or short in communication lines

·

LIN communication error detected by the certification ECU (smart key ECU assembly) 3 times in a row.


·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

B219678E28
0.969,1.656 2.75,2.188 1.781,0.531 10 Steering Lock ECU (Steering Lock Actuator Assembly) 1.115,2.375 2.896,2.625 1.781,0.25 10 : LIN Communication Line 4.448,1.656 6.052,2.292 1.604,0.635 10 Certification ECU (Smart Key ECU Assembly) 0.969,1.49 1.354,1.719 0.385,0.229 10 I24 4.448,1.49 4.938,1.823 0.49,0.333 10 I78 4.469,0.896 5.083,1.25 0.615,0.354 10 LIN 4.208,0.729 4.583,1.115 0.375,0.385 10 17 2.51,0.896 2.917,1.208 0.406,0.313 10 LIN 2.833,0.729 3.156,1.073 0.323,0.344 10 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to the Service Bulletin).

·

If the steering lock ECU (steering lock actuator assembly) is replaced, register the ECU code (refer to the Service Bulletin).

·

When using the intelligent tester to troubleshoot with the ignition switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
a.

Disconnect the I24 steering lock ECU (steering lock actuator assembly) connector.


b.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-17 (LIN) - I24-5 (LIN) Always Below 1 Ω
I78-17 (LIN) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
I78-17 (LIN) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
a.

Reconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

c.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)