Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074557 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the navigation ECU sub-assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E224380E44
1.135,3.219 2.885,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.635 3.583,0.813 0.354,0.177 10 false BAT 3.229,1.74 3.563,1.917 0.333,0.177 10 false ESS 2.021,1.354 3.031,1.531 1.01,0.177 10 false ECU-IG1 NO. 1 2.042,0.792 2.969,0.969 0.927,0.177 10 false ECU-B NO.1 0.333,1.198 1.927,1.552 1.594,0.354 10 false from IG1 NO. 2 Relay 0.896,0.635 1.823,0.813 0.927,0.177 10 false from Battery 3.188,2.375 4.26,2.792 1.073,0.417 10 false Steering Sensor 3.031,0.552 3.156,0.729 0.125,0.177 10 false 5 3.031,1.094 3.156,1.271 0.125,0.177 10 false 4 3.031,1.646 3.156,1.823 0.125,0.177 10 false 1 3.229,1.188 3.531,1.365 0.302,0.177 10 false IG 4.99,2.177 5.271,2.354 0.281,0.177 10 false I67 3.198,2.188 3.542,2.365 0.344,0.177 10 false I29 4.99,2.354 6.927,2.708 1.938,0.354 10 false Navigation ECU Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SUPPLY)
a.
E224381C01
1.49,0.156 1.979,0.448 0.49,0.292 2.052,1.51 2.49,1.51 false 1.865,1.583 1.865,1.885 1.865,1.885 2.49,1.885 false 1.427,1.583 1.427,1.885 1.427,1.885 0.802,1.885 false 0.458,1.802 0.875,2 0.417,0.198 10 ESS 2.521,1.802 2.938,2 0.417,0.198 10 IG 2.521,1.427 2.938,1.625 0.417,0.198 10 BAT 0.208,0.073 0.625,0.271 0.417,0.198 10 *a 1.615,0.219 1.885,0.396 0.271,0.177 10 I29
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the I29 connector from the steering sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I29-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I29-4 (IG) - I29-1 (ESS) Engine switch on (IG) 11 to 14 V
I29-5 (BAT) - I29-1 (ESS) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR