This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB4 | Open in Outer Mirror Indicator(Master) | Both of the following conditions are met:
·
Blind spot monitor main switch (warning canceling switch assembly) is on. ·
The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator. |
·
Outer rear view mirror RH ·
Mirror sub-assembly RH ·
Wire harness or connector ·
Blind spot monitor sensor RH ·
Outer mirror control ECU assembly RH |
When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect connector O28 from the blind spot monitor sensor RH.
Disconnect connector J13 from the outer mirror control ECU assembly RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O28-6 (OMIR) - J13-10 (BDSR) | Always | Below 1 Ω |
| J13-7 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector z6 from the outer mirror control ECU assembly RH.
| *1 | Outer Rear View Mirror Indicator RH |
| *a | Component without harness connected
(Mirror Sub-assembly RH) |
Check that the outer rear view mirror indicator turns on.
Do not apply a voltage of more than 6 V.
Connect 4 new 1.5 V dry-cell batteries in series.
Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.OK:
| Connection | Specified Condition |
|---|---|
| 6 V battery positive (+) → z6-7 (BDIR)
6 V battery negative (-) → z6-12 (HTR-) |
Indicator turns on |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector J13 from the outer mirror control ECU assembly RH.
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J13-10 (BDSR) - z6-7 (BDIR) | Always | Below 1 Ω |
| J13-7 (GND) - z6-12 (HTR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector IND1 from the outer rear view mirror RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-7 (BDIR) - IND1-1 (+) | Always | Below 1 Ω |
| z6-12 (HTR-) - IND1-2 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG