Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074560 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E224413E11
3.625,0.719 3.938,0.896 0.313,0.177 10 false BLB 3.458,0.604 3.573,0.781 0.115,0.177 10 false 5 3.625,3.302 3.938,3.479 0.313,0.177 10 false BRB 3.458,3.198 3.573,3.375 0.115,0.177 10 false 5 3.656,4.104 4.094,4.281 0.438,0.177 10 false BRGD 3.458,3.979 3.573,4.156 0.115,0.177 10 false 1 3.458,1.396 3.573,1.573 0.115,0.177 10 false 1 3.625,1.51 4.052,1.667 0.427,0.156 10 false BLGD 1.604,0.865 2.635,1.031 1.031,0.167 10 false ECU-IG1 NO. 3 0.219,0.708 1.219,1.208 1,0.5 10 false from IG1 NO. 2 Relay 6.365,1.104 6.896,1.281 0.531,0.177 10 false to CAN 3.417,2.052 3.958,2.333 0.542,0.281 10 false T16 3.417,2.219 5.031,2.563 1.615,0.344 10 false Blind Spot Monitor Sensor LH 3.469,4.802 5.083,5.146 1.615,0.344 10 false Blind Spot Monitor Sensor RH 0.875,5.302 2.719,5.458 1.844,0.156 10 false : CAN Communication Line 3.469,4.635 3.875,4.792 0.406,0.156 10 false O28

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O28-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V
O28-5 (BRB) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O28-1 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY)
a.

Disconnect connector T16 from the blind spot monitor sensor LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T16-5 (BLB) - Body ground Engine switch on (IG) 11 to 14 V
T16-5 (BLB) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)
a.

Disconnect connector T16 from the blind spot monitor sensor LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-1 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR