Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
|---|---|
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except radio receiver assembly. | B |
| No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). | C |
A
B
C
Disconnect the spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I28-13 (IL+2) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the steering pad switch assembly connector.
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Check if the illumination for the steering pad switch assembly comes on.
Illumination for the steering pad switch assembly comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the steering pad switch assembly and spiral cable sub-assembly connectors.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-5 (IL+2) - I28-13 (IL+2) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-3 (-DP) - I28-11 (-DP) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-5 (IL+2) - I28-13 (IL+2) | Always | Below 3 Ω |
| z3-3 (-DP) - I28-11 (-DP) | Always | Below 3 Ω |
Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.
The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Removal
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Installation
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I148-10 (ILL+) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG