Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0077308 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Speaker Circuit  


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.

If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

E238696E12
0.406,1.25 1.708,1.719 1.302,0.469 10 false Front No. 1 Speaker Assembly LH 0.365,3.177 1.667,3.594 1.302,0.417 10 false Front No. 1 Speaker Assembly RH 3.01,1.219 4.302,1.667 1.292,0.448 10 false Front No. 2 Speaker Assembly LH 3.031,3.229 4.333,3.635 1.302,0.406 10 false Front No. 2 Speaker Assembly RH 0.813,5 1.729,5.438 0.917,0.438 10 false Rear Speaker Assembly LH 0.802,6.51 1.698,6.948 0.896,0.438 10 false Rear Speaker Assembly RH 1.833,1.104 2.094,1.365 0.26,0.26 10 false 1 2.313,0.833 2.542,1.021 0.229,0.188 10 false 3 1.833,3.052 2.063,3.313 0.229,0.26 10 false 1 2.313,2.823 2.583,3.146 0.271,0.323 10 false 3 5.542,2.719 5.781,2.938 0.24,0.219 10 false 1 1.844,4.865 2.021,5.021 0.177,0.156 10 false 1 1.813,6.385 2.083,6.656 0.271,0.271 10 false 1 5.542,6.177 5.719,6.333 0.177,0.156 10 false 1 1.854,1.667 2.125,1.948 0.271,0.281 10 false 2 1.844,3.646 2.104,4 0.26,0.354 10 false 2 1.854,5.469 2.115,5.677 0.26,0.208 10 false 2 1.823,6.969 2.042,7.167 0.219,0.198 10 false 2 5.542,4.646 5.781,4.885 0.24,0.24 10 false 2 4.552,0.823 4.781,1.073 0.229,0.25 10 false 4 4.552,2.802 4.802,3.115 0.25,0.313 10 false 4 5.542,0.75 5.792,0.979 0.25,0.229 10 false 2 5.552,6.802 5.813,7 0.26,0.198 10 false 3 2.302,1.708 2.646,1.948 0.344,0.24 10 false 1 2.313,3.677 2.594,4.042 0.281,0.365 10 false 1 4.552,1.719 4.865,1.927 0.313,0.208 10 false 2 4.542,3.677 5.031,4.135 0.49,0.458 10 false 2 4.052,2.802 4.583,3.083 0.531,0.281 10 false TWR+ 4.052,3.885 4.729,4.219 0.677,0.333 10 false TWR- 2.469,2.813 2.833,2.969 0.365,0.156 10 false + 2.49,3.865 2.854,4.021 0.365,0.156 10 false - 2.49,0.823 2.854,1 0.365,0.177 10 false + 2.5,1.917 2.76,2.073 0.26,0.156 10 false - 4.083,0.823 4.646,1.115 0.563,0.292 10 false TWL+ 4.104,1.938 4.573,2.229 0.469,0.292 10 false TWL- 5.552,3.615 5.76,3.844 0.208,0.229 10 false 5 5.542,1.625 5.865,1.927 0.323,0.302 10 false 6 5.552,5.292 5.792,5.521 0.24,0.229 10 false 6 5.833,0.958 6.302,1.25 0.469,0.292 10 false FL+ 5.833,1.813 6.177,2.031 0.344,0.219 10 false FL- 5.833,2.938 6.333,3.198 0.5,0.26 10 false FR+ 5.833,3.771 6.198,3.927 0.365,0.156 10 false FR- 5.833,4.865 6.25,5.177 0.417,0.313 10 false RL+ 5.833,5.49 6.198,5.792 0.365,0.302 10 false RL- 5.833,6.375 6.229,6.625 0.396,0.25 10 false RR+ 5.833,7 6.292,7.281 0.458,0.281 10 false RR- 5.458,0.948 5.979,1.313 0.521,0.365 10 false I148 5.469,2.927 5.927,3.302 0.458,0.375 10 false I148 5.458,3.792 5.854,4.063 0.396,0.271 10 false I148 5.458,1.823 5.906,2.094 0.448,0.271 10 false I148 5.458,4.844 5.979,5.125 0.521,0.281 10 false I149 5.469,5.479 5.875,5.75 0.406,0.271 10 false I149 5.469,6.365 5.896,6.604 0.427,0.24 10 false I149 5.469,7 5.865,7.208 0.396,0.208 10 false I149 0.406,1.094 0.885,1.458 0.479,0.365 10 false K5 0.375,3.01 0.729,3.323 0.354,0.313 10 false J5 0.813,4.844 1.25,5.063 0.438,0.219 10 false O21 0.802,6.354 1.219,6.625 0.417,0.271 10 false O18 3.01,1.073 3.323,1.271 0.313,0.198 10 false I1 3.031,3.073 3.406,3.344 0.375,0.271 10 false I83 5.771,7.479 6.75,7.99 0.979,0.51 10 false Radio Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Disconnect the connectors from the radio receiver assembly and speakers.


b.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I148-1 (FR+) - I83-4 (TWR+) Always Below 1 Ω
I148-5 (FR-) - I83-2 (TWR-) Always Below 1 Ω
I148-2 (FL+) - I1-4 (TWL+) Always Below 1 Ω
I148-6 (FL-) - I1-2 (TWL-) Always Below 1 Ω



c.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-3 (+) - K5-1 Always Below 1 Ω
I1-1 (-) - K5-2 Always Below 1 Ω
I83-3 (+) - J5-1 Always Below 1 Ω
I83-1 (-) - J5-2 Always Below 1 Ω



d.

Measure the resistance between each of the rear speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I149-1 (RR+) - O18-1 Always Below 1 Ω
I149-3 (RR-) - O18-2 Always Below 1 Ω
I149-2 (RL+) - O21-1 Always Below 1 Ω
I149-6 (RL-) - O21-2 Always Below 1 Ω



e.

Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I148-1 (FR+) - Body ground Always 10 kΩ or higher
I148-5 (FR-) - Body ground Always 10 kΩ or higher
I148-2 (FL+) - Body ground Always 10 kΩ or higher
I148-6 (FL-) - Body ground Always 10 kΩ or higher
I149-1 (RR+) - Body ground Always 10 kΩ or higher
I149-3 (RR-) - Body ground Always 10 kΩ or higher
I149-2 (RL+) - Body ground Always 10 kΩ or higher
I149-6 (RL-) - Body ground Always 10 kΩ or higher



f.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-3 (+) - Body ground Always 10 kΩ or higher
I1-1 (-) - Body ground Always 10 kΩ or higher
I83-3 (+) - Body ground Always 10 kΩ or higher
I83-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
E219303C10
0.354,1.917 0.885,2.208 0.531,0.292 0.354,1.542 0.885,1.833 0.531,0.292 0.531,1.979 1,2.302 0.469,0.323 10 K5 0.563,1.604 0.938,1.906 0.375,0.302 10 J5 0.25,0.229 0.677,0.552 0.427,0.323 10 *a 0.958,1.594 1.375,1.938 0.417,0.344 10 *A 0.958,1.979 1.167,2.208 0.208,0.229 10 *B
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 - J5-2 Always 3.2 to 4.8 Ω
K5-1 - K5-2 Always 3.2 to 4.8 Ω




Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
E226097C06
1.469,0.656 1.927,0.938 0.458,0.281 1.458,1 1.917,1.281 0.458,0.281 1.396,1.802 1.042,2.292 false 1.677,1.813 1.542,2.292 false 2.24,1.792 2.604,2.313 false 1.99,1.802 2.125,2.292 false 0.198,0.208 0.708,0.594 0.51,0.385 10 *a 1.979,0.729 2.344,1.031 0.365,0.302 10 *A 1.979,1.073 2.365,1.344 0.385,0.271 10 *B 1.615,0.719 1.969,0.917 0.354,0.198 10 I83 1.656,1.063 2,1.313 0.344,0.25 10 I1 1.5,2.313 1.76,2.646 0.26,0.333 10 + 0.573,2.313 1.188,2.531 0.615,0.219 10 TWR+*A 0.573,2.51 1.219,2.74 0.646,0.229 10 TWL+*B 1.802,2.323 2.448,2.583 0.646,0.26 10 TWR-*A 1.802,2.531 2.417,2.813 0.615,0.281 10 TWL-*B 2.646,2.313 2.813,2.573 0.167,0.26 10 -
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-4 (TWR+) - I83-2 (TWR-) Always 10 kΩ or higher
I83-1 (-) - I83-2 (TWR-) Always Below 1 Ω
I83-3 (+) - I83-4 (TWR+) Always Below 1 Ω
I1-4 (TWL+) - I1-2 (TWL-) Always 10 kΩ or higher
I1-1 (-) - I1-2 (TWL-) Always Below 1 Ω
I1-3 (+) - I1-4 (TWL+) Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.



Result:
Proceed to
OK
NG




OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

5.INSPECT REAR SPEAKER ASSEMBLY
5.INSPECT REAR SPEAKER ASSEMBLY
a.
E219303C11
0.469,1.917 1,2.208 0.531,0.292 0.469,1.542 1,1.833 0.531,0.292 0.615,1.979 1.094,2.25 0.479,0.271 10 O21 0.615,1.604 1.271,1.896 0.656,0.292 10 O18 0.198,0.24 0.5,0.531 0.302,0.292 10 *a 1.073,1.594 1.438,2.063 0.365,0.469 10 *A 1.073,1.979 1.396,2.375 0.323,0.396 10 *B
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O18-1 - O18-2 Always 3.2 to 4.8 Ω
O21-1 - O21-2 Always 3.2 to 4.8 Ω




Result:
Proceed to
OK
NG



OK

NG