Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2030EQ _58 Vehicle Interior _014670 SEAT _0077330 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY


a.

for LHD

i.

Disconnect the e11 and e12 position control ECU and switch assembly connectors.

B219506
4.01,0.219 4.469,0.469 0.458,0.25 3.01,0.219 3.469,0.469 0.458,0.25 4.156,0.26 4.708,0.625 0.552,0.365 10 false e12 3.146,0.26 3.615,0.531 0.469,0.271 10 false e11


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal Connection Wiring Color Terminal Description Condition Specified Condition
e11-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
e11-7 (+B) - e11-2 (GND) W - W-B Power source Always 11 to 14 V
e12-12 (SYSB) - e11-2 (GND) P - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


iii.

Reconnect the e11 and e12 position control ECU and switch assembly connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal Connection Wiring Color Terminal Description Condition Specified Condition
e11-6 (+B2) - e11-1 (GND2) SB - W-B Lumbar support adjuster power source Always 11 to 14 V
e11-1 (GND2) - Body ground W-B - Body ground Lumbar support adjuster ground Always Below 1 Ω
e11-3 (SLD+) - e11-2 (GND) L - W-B Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
e11-4 (SLD-) - e11-2 (GND) GR - W-B Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
e11-5 (FRV-) - e11-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
e11-8 (FRV+) - e11-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
e11-9 (RCL+) - e11-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
e11-11 (RCL-) - e11-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
e11-10 (LFT+) - e11-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
e11-12 (LFT-) - e11-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
e12-1 (SGND) - e11-2 (GND) BR - W-B Position sensor round Always Below 1 Ω
e12-3 (SSFV) - e12-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
e12-4 (SSRL) - e12-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
e12-5 (SSRS) - e12-1 (SGND) G- BR Slide position signal Slide function operating 4.5 to 4.8 V
e12-11 (SSRR) - e12-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the position control ECU and switch assembly may have a malfunction.



b.

for RHD

i.

Disconnect the d11 and d12 position control ECU and switch assembly connectors.

B219505
3.816,0.29 4.071,0.428 0.255,0.138 10 d11 2.922,0.289 3.171,0.43 0.249,0.142 10 d12 2.863,0.264 3.201,0.462 0.338,0.199 3.747,0.264 4.084,0.462 0.338,0.199


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal Connection Wiring Color Terminal Description Condition Specified Condition
d11-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
d11-7 (+B) - d11-2 (GND) W - W-B Power source Always 11 to 14 V
d12-12 (SYSB) - d11-2 (GND) P - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


iii.

Reconnect the d11 and d12 position control ECU and switch assembly connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal Connection Wiring Color Terminal Description Condition Specified Condition
d11-6 (+B2) - d11-1 (GND2) SB - W-B Lumbar support adjuster power source Always 11 to 14 V
d11-1 (GND2) - Body ground W-B - Body ground Lumbar support adjuster ground Always Below 1 Ω
d11-3 (SLD+) - d11-2 (GND) L - W-B Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
d11-4 (SLD-) - d11-2 (GND) GR - W-B Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
d11-5 (FRV-) - d11-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
d11-8 (FRV+) - d11-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
d11-9 (RCL+) - d11-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
d11-11 (RCL-) - d11-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
d11-10 (LFT+) - d11-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
d11-12 (LFT-) - d11-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
d12-1 (SGND) - d11-2 (GND) BR - W-B Position sensor round Always Below 1 Ω
d12-3 (SSFV) - d12-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
d12-4 (SSRL) - d12-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
d12-5 (SSRS) - d12-1 (SGND) G- BR Slide position signal Slide function operating 4.5 to 4.8 V
d12-11 (SSRR) - d12-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the position control ECU and switch assembly may have a malfunction.




CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver)


B209687
4.354,0.188 4.667,0.396 0.313,0.208 3.74,0.198 4.052,0.406 0.313,0.208 4.396,0.219 4.698,0.365 0.302,0.146 10 false J13 4.094,0.229 4.302,0.417 0.208,0.188 10 false *A 3.771,0.219 4.073,0.365 0.302,0.146 10 false K12 4.729,0.24 4.938,0.427 0.208,0.188 10 false *B
*A for LHD *B for RHD


a.

for LHD

i.

Disconnect the K12 outer mirror control ECU assembly (for Driver) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K12-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K12-14 (BDR) - K12-7 (GND) W - W-B Power source Always 11 to 14 V
K12-5 (SIG) - K12-7 (GND) GR - W-B Power source (IG) Always Below 1 V
Engine switch on (IG) 11 to 14 V
K12-6 (CPUB) - K12-7 (GND) W - W-B Power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the K12 outer mirror control ECU assembly (for Driver) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K12-3 (M2) - K12-13 (MSWE) G - B M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
K12-2 (M1) - K12-13 (MSWE) R - B M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
K12-1 (MM) - K12-13 (MSWE) P - B SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

If the result is not as specified, the outer mirror control ECU assembly (for Driver) may have a malfunction.



b.

for RHD

i.

Disconnect the J13 outer mirror control ECU assembly (for Driver) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J13-14 (BDR) - J13-7 (GND) W - W-B Power source Always 11 to 14 V
J13-5 (SIG) - J13-7 (GND) BE - W-B Power source (IG) Always Below 1 V
Engine switch on (IG) 11 to 14 V
J13-6 (CPUB) - J13-7 (GND) W - W-B Power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the J13 outer mirror control ECU assembly (for Driver) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-3 (M2) - J13-13 (MSWE) B - V M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J13-2 (M1) - J13-13 (MSWE) G - V M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J13-1 (MM) - J13-13 (MSWE) P - V SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

If the result is not as specified, the outer mirror control ECU assembly (for Driver) may have a malfunction.




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Disconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connectors.

B278841
2.198,3.771 2.521,3.979 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 5.823,4.813 6.146,5.021 0.323,0.208 5.823,5.083 6.146,5.292 0.323,0.208 4.042,1.135 4.042,0.802 4.042,0.802 4.156,0.802 false 1.677,1.615 1.938,1.615 false 1.677,2.01 1.938,2.01 false 0.802,2.76 1.031,2.76 false 1.615,0.948 1.615,0.646 1.615,0.646 1.792,0.646 false 1.469,3.167 1.469,1.521 1.469,1.521 1.563,1.521 false 1.469,1.948 1.563,1.948 false 4.188,0.719 4.479,0.927 0.292,0.208 10 false MB 3.438,7.563 3.885,7.802 0.448,0.24 10 false MB 0.896,1.521 1.198,1.74 0.302,0.219 10 false 3C 1.156,5.031 1.625,5.281 0.469,0.25 10 false 3C 5.865,1.458 6.135,1.635 0.271,0.177 10 false 3B 1.823,6.313 2.396,6.583 0.573,0.271 10 false 3B 5.854,2.135 6.104,2.313 0.25,0.177 10 false 3A 4.969,6.313 5.281,6.594 0.313,0.281 10 false 3A 0.906,2.104 1.198,2.292 0.292,0.188 10 false 3D 3.948,5.021 4.521,5.354 0.573,0.333 10 false 3D 1.99,1.542 2.354,1.74 0.365,0.198 10 false I13 4.719,3.792 5.135,4.021 0.417,0.229 10 false I13 1.99,1.948 2.344,2.167 0.354,0.219 10 false I12 2.271,3.792 2.708,4.042 0.438,0.25 10 false I12 5.906,4.844 6.24,5.115 0.333,0.271 10 false 3E 1.833,0.552 2.198,0.75 0.365,0.198 10 false *1 0.219,0.188 0.594,0.417 0.375,0.229 10 false *A 1.417,3.219 1.781,3.417 0.365,0.198 10 false *2 0.073,2.677 0.865,2.948 0.792,0.271 10 false 3E*B, 3F*C 5.917,5.115 6.25,5.385 0.333,0.271 10 false 3F 6.198,5.115 6.531,5.385 0.333,0.271 10 false *C 6.198,4.833 6.531,5.104 0.333,0.271 10 false *B
*A Main body ECU (multiplex network body ECU) with 2 connectors *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096
2.229,3.771 2.552,3.979 0.323,0.208 5.833,4.885 6.156,5.094 0.323,0.208 5.833,5.125 6.156,5.333 0.323,0.208 3.906,5.031 4.229,5.24 0.323,0.208 1.125,5.01 1.448,5.219 0.323,0.208 1.781,6.292 2.104,6.5 0.323,0.208 4.927,6.292 5.25,6.5 0.323,0.208 3.417,7.531 3.74,7.74 0.323,0.208 4.688,3.771 5.01,3.979 0.323,0.208 4.083,1.125 4.083,0.844 4.083,0.844 4.198,0.844 false 1.823,2.104 2.073,2.104 false 0.771,2.771 1.031,2.771 false 1.823,1.75 2.073,1.75 false 1.604,3.083 1.604,1.427 1.604,1.427 1.708,1.427 false 1.604,1.75 1.698,1.75 false 1.604,2.104 1.708,2.104 false 1.771,0.979 1.771,0.688 1.771,0.688 1.865,0.688 false 3.479,7.563 3.875,7.792 0.396,0.229 10 false MB 5.917,4.917 6.333,5.208 0.417,0.292 10 false 3E 6.177,4.917 6.49,5.208 0.313,0.292 10 false *B 1.198,5.042 1.708,5.354 0.51,0.313 10 false 3C 1.865,6.323 2.323,6.635 0.458,0.313 10 false 3B 5.01,6.333 5.344,6.573 0.333,0.24 10 false 3A 3.979,5.063 4.333,5.313 0.354,0.25 10 false 3D 4.771,3.813 5.083,4.01 0.313,0.198 10 false I13 2.302,3.813 2.604,4 0.302,0.188 10 false I12 5.917,5.156 6.25,5.406 0.333,0.25 10 false 3F 6.177,5.156 6.573,5.427 0.396,0.271 10 false *C 5.865,2.146 6.198,2.354 0.333,0.208 10 false 3A 2.125,2.042 2.427,2.25 0.302,0.208 10 false I12 2.125,1.677 2.427,1.917 0.302,0.24 10 false I13 0.906,2.094 1.104,2.229 0.198,0.135 10 false 3D 0.052,2.698 0.875,2.906 0.823,0.208 10 false 3E*B, 3F*C 0.906,1.458 1.104,1.594 0.198,0.135 10 false 3C 5.865,1.469 6.156,1.635 0.292,0.167 10 false 3B 4.229,0.771 4.594,1.01 0.365,0.24 10 false MB 0.323,0.229 0.729,0.51 0.406,0.281 10 false *A 1.906,0.625 2.198,0.865 0.292,0.24 10 false *1 1.542,3.094 1.688,3.229 0.146,0.135 10 false *2
*A Main body ECU (multiplex network body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Engine switch on (IG) → off 11 to 14 V → Below 1 V
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Engine switch on (ACC) → off 11 to 14 V → Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-2 (FLCY) - Body ground*1 - Front door courtesy light switch LH input Front door LH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
I13-19 (FRCY) - Body ground*2 Y - Body ground Front door courtesy light switch RH input Front door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

*1: for LHD

*2: for RHD


If the result is not as specified, there may be a malfunction in the wire harness.