Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2030EQ _58 Vehicle Interior _014670 SEAT _0077330 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless-linked Return Function does not Operate  


DESCRIPTION

When a door is unlocked using the wireless unlock function or entry unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call and memory command information of the stored key ID is sent to each driving position related control ECU. Each control ECU receives the memory commands and performs the memory call operation according to predetermined control timing values.

CAUTION / NOTICE / HINT

NOTICE:

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
a.

b.

Check whether seat positions can be stored in memory.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


c.

Check whether seat positions can be restored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


d.

Check the operation of memory call registration.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
OK A
NG (power seat operation) B
NG (seat position memory) C
NG (seat position restoring) D
NG (memory call registration) E




A

2.CHECK MEMORY CALL FUNCTION (WIRELESS UNLOCK OR ENTRY UNLOCK)

B

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

D

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

E

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless Transmitter Memory Function does not Operate)

2.CHECK MEMORY CALL FUNCTION (WIRELESS UNLOCK OR ENTRY UNLOCK)
a.

Turn the engine switch off.


b.

Close and lock all doors.


c.

Unlock the driver door by pressing the unlock switch of the memory call registered key (wireless unlock function).


d.

Unlock the driver door by touching the driver door outside handle while holding the memory call registered key (entry unlock function).


e.

Open the driver door and check that the driver seat moves to the memorized position.

Result:
Result Proceed to
Memory call function linked with the wireless unlock function does not operate. A
Memory call function linked with the entry unlock function does not operate. B
Both memory call function linked with the wireless unlock function and entry unlock function do not operate. C




A

3.CHECK WIRELESS UNLOCK FUNCTION

B

9.CHECK SMART ENTRY AND START SYSTEM (ENTRY UNLOCK FUNCTION)

C

15.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
3.CHECK WIRELESS UNLOCK FUNCTION
a.

Check the wireless unlock function.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless unlock function is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)

NG

4.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
a.

Use the memory call function and check the outer mirror operation.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
Outer mirrors operate normally A
Outer mirrors do not operate normally B




A

5.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

7.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
5.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MEMORY CALL FUNCTION
6.CHECK MEMORY CALL FUNCTION


c.

Turn the engine switch off.


d.

Close and lock all doors.


e.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


f.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK MEMORY CALL FUNCTION
8.CHECK MEMORY CALL FUNCTION


c.

Turn the engine switch off.


d.

Close and lock all doors.


e.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


f.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK SMART ENTRY AND START SYSTEM (ENTRY UNLOCK FUNCTION)
a.

Check the entry unlock function of the smart entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry unlock function is normal.



Result:
Proceed to
OK
NG



OK

10.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)

NG

10.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
a.

Use the memory call function and check the outer mirror operation.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
Outer mirrors operate normally A
Outer mirrors do not operate normally B




A

11.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

13.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
11.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK MEMORY CALL FUNCTION
12.CHECK MEMORY CALL FUNCTION


c.

Turn the engine switch off.


d.

Close and lock all doors.


e.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


f.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

13.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK MEMORY CALL FUNCTION
14.CHECK MEMORY CALL FUNCTION


c.

Turn the engine switch off.


d.

Close and look all doors.


e.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


f.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
a.

Use the memory call function and check the outer mirror operation.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
Outer mirrors operate normally A
Outer mirrors do not operate normally B




A

16.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

18.READ VALUE USING INTELLIGENT TESTER (MEMORY CALL REGISTRATION)
16.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CHECK MEMORY CALL FUNCTION
17.CHECK MEMORY CALL FUNCTION


c.

Turn the engine switch off.


d.

Close and lock all doors.


e.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


f.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

18.READ VALUE USING INTELLIGENT TESTER (MEMORY CALL REGISTRATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1*
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2*
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3*
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4*
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5*
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6*
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7*
-

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191

f.

Enter the following menus: Body / Driver Seat / Data List.


g.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

On the intelligent tester display, it is confirmed that the memory switch which is linked with a key ID has a memorized seat position. (For example, on the intelligent tester display, "Mem SW No. w/ KeyID1" displays "MEM SW1" and "Seat Memory No1" displays "Mem".)



Result:
Proceed to
OK
NG



OK

19.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR COURTESY SWITCH)

NG

19.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly signal ON or OFF ON: Driver door open
OFF: Driver door closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

On the intelligent tester screen, each item changes between ON and OFF according to the above.



Result:
Proceed to
OK
NG



OK

20.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)

20.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CHECK MEMORY CALL FUNCTION
21.CHECK MEMORY CALL FUNCTION


c.

Turn the engine switch off.


d.

Close and lock all doors.


e.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


f.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)