Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2013.07
RM2030EQ _58 Vehicle Interior _014671 SEAT BELT _0077141 SEAT BELT WARNING SYSTEM G

SEAT BELT  SEAT BELT WARNING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

After 1.8 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.*1


c.

When the shift lever is in P and the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.*2


d.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


e.

Start the engine.


f.

Check the state of the seat belt warning light on the combination meter assembly under the following conditions:

i.

Step 1:

When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released for 30 seconds or more, check that the seat belt warning light on the combination meter assembly blinks.


ii.

Step 2:

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

After 59.6*1 or 150*2 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


iii.

Step 3:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


iv.

Step 4:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


v.

Step 5:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

*1: for LHD

*2: for RHD




Hide 2.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT (for RHD)

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

When the front passenger seat belt is not fastened with the front passenger seat occupied, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

After 1.8 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.*1


c.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



d.

Fasten the driver seat belt.


e.

When the shift lever is in P, the front passenger seat is occupied and the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.*2


f.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


g.

Start the engine.


h.

Check the state of the seat belt warning light on the combination meter assembly under the following conditions:

i.

Step 1:

When the front passenger seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released for 30 seconds or more, check that the seat belt warning light on the combination meter assembly blinks.


ii.

Step 2:

When the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

After 150 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


iii.

Step 3:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


iv.

Step 4:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.


v.

Step 5:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, the front passenger seat belt not fastened and the weight on the front passenger seat, check that the seat belt warning light on the combination meter assembly turns off when the weight is removed from the front passenger seat.


vi.

Step 6:

Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

*1: for LHD

*2: for RHD




Hide 3.INSPECT REAR SEAT BELT WARNING (for RHD)

a.
B294180
1.115,1.438 1.115,1.833 false 1.708,1.438 1.708,1.833 false 2.302,1.438 2.302,1.833 false 0.208,0.146 0.708,0.479 0.5,0.333 10 false *a 1.052,1.875 1.427,2.177 0.375,0.302 10 false *b 1.646,1.875 2.042,2.146 0.396,0.271 10 false *c 2.24,1.875 2.51,2.094 0.271,0.219 10 false *d
*a Rear Seat Belt Warning Light (Clock Assembly)
*b LH
*c Center
*d RH


Open and then close either rear door.


b.

Turn the ignition switch to ON.


c.

When the rear seat belt is not fastened, check that the rear seat belt warning light on the clock assembly illuminates.


d.

When either condition is met, check that the rear seat belt warning light on the clock assembly turns off:

·

The rear seat belt is fastened.

·

The vehicle is not driven and either rear door is opened.



Hide 4.INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON .

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

for LHD

i.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



ii.

After turning the ignition switch to ON, if the driver seat belt is not fastened within 1.8 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at 1.2 second intervals for 6 seconds.


iii.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


iv.

Start the engine.


v.

When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds once.


vi.

When 30 seconds have passed after the buzzer sounded, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 9.6 seconds.


vii.

After the seat belt warning buzzer has been sounding for 9.6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 20 seconds.


viii.

Check that the seat belt warning buzzer in the combination meter assembly stops 29.6 seconds after it started sounding at an interval of 1.2 seconds.


ix.

After the seat belt warning buzzer in the combination meter assembly stops, the ignition switch is turned off and the engine is restarted, check that the buzzer sounds once again and then sounds according to the appropriate pattern when the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened.


x.

After the seat belt warning buzzer in the combination meter assembly stops and the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt fastened, when the driver or front passenger seat belt is unfastened, check that the buzzer sounds once again and then sounds according to the appropriate pattern.


xi.

After the seat belt warning buzzer in the combination meter assembly stops sounding and the shift lever is moved to R and then back to D, when the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened, check that the buzzer sounds once again and then sounds according to the appropriate pattern.



b.

for RHD

i.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



ii.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


iii.

Start the engine.


iv.

Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.


v.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.


vi.

Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.


vii.

After the buzzer has stopped, turn the ignition switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver, front passenger or rear seat belt is not fastened, and check that the buzzer sounds again.


viii.

After the buzzer has stopped, fasten the driver, front passenger or rear seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver, front passenger or rear seat belt, and check that the buzzer sounds again.


ix.

After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.