The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (for driver).
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Seat Buckle SW | Driver seat belt buckle switch | ON or OFF | ON: Driver seat belt unfastened
OFF: Driver seat belt fastened |
- |
| Tester Display |
|---|
| D Seat Buckle SW |
ON or OFF appears on the tester screen according to the driver seat belt condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Seat belt warning light | OFF/ON | - |
| Tester Display |
|---|
| Driver Side Seat Belt |
The seat belt warning light on the combination meter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Front Seat Inner Belt Assembly (for Driver)) |
Remove the front seat inner belt assembly (for driver).
for LHD: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for LHD)>REMOVAL
for RHD: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 3 | Driver seat belt unfastened | Below 1 Ω |
| 2 - 3 | Driver seat belt fastened | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for LHD)>REMOVAL
for RHD: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Disconnect the 3C instrument panel junction block assembly. (for LHD)
Disconnect the 3A instrument panel junction block assembly. (for RHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-18 (DBKL) - 3C-35 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-18 (DBKL) - 3A-38 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-35 - N2-3 | Always | Below 1 Ω |
| N2-3 - Body ground | Always | 10 kΩ or higher |
| N2-2 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-38 - O3-3 | Always | Below 1 Ω |
| O3-3 - Body ground | Always | 10 kΩ or higher |
| O3-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG