Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.05
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074476 DIFFERENTIAL CASE A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41311F 1.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C201521
2.458,0.592 2.768,0.735 0.31,0.143 10 SST 1.87,0.803 2.406,0.689 2.406,0.689 1.887,1.007 false 1.747,0.661 2.406,0.689 false

Using SST and a press, install a new front differential case rear tapered roller bearing to the front differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing cage when installing the front differential case rear tapered roller bearing.

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing and front differential case.




b.
C196828
0.885,1.125 0.573,1.396 0.573,1.396 0.74,1.396 false 2.635,1.104 2.563,0.802 2.563,0.802 2.667,0.802 false 0.219,1.323 0.531,1.479 0.313,0.156 10 true SST 2.24,0.719 2.552,0.875 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing outer race to the transaxle case sub-assembly.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing outer race and transaxle case sub-assembly.



Hide 41311E 2.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C297473
0.833,0.823 0.406,0.458 0.406,0.458 0.927,0.51 false 0.427,0.469 0.865,0.698 false 2.365,0.604 2.292,0.281 2.292,0.281 2.552,0.323 false 2.302,0.292 2.479,0.51 false 0.104,0.375 0.563,0.573 0.458,0.198 10 false SST 1.99,0.198 2.448,0.396 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing to the front differential case.

SST
09523-36010  
09950-60010  (09951-00540)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing cage when installing the front differential case front tapered roller bearing.

·

Ensure that there is no clearance between the front differential case front tapered roller bearing and front differential case.




b.
C196830
0.938,1.24 0.625,1.594 0.625,1.594 0.896,1.531 false 2.604,0.698 2.5,0.698 2.5,0.698 2.552,1.073 false 0.281,1.542 0.594,1.708 0.313,0.167 10 false SST 2.188,0.635 2.49,0.802 0.302,0.167 10 false SST

Install the shim to the transaxle housing.


c.

Using SST and a hammer, install a new front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case front tapered roller bearing outer race, shim and transaxle housing.



Hide 41221 3.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.
C138531
1.26,1.438 0.552,0.969 0.552,0.969 1.177,1.5 false 0.354,0.854 0.635,1.063 0.281,0.208 10 false *a
*a Matchmark


Clean the contact surface of the front differential case.


c.

Align the matchmarks, and install the front differential ring gear to the front differential case quickly.


d.
C138532

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 88 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 4.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

ATF


Coat the front differential side gear, front No. 1 differential side gear thrust washer and conical spring with ATF.


b.
C304161
2.292,1.865 2.406,1.865 false 2.292,0.323 2.427,0.323 false 2.302,0.552 2.573,0.552 false 2.292,1.49 2.573,1.49 false 2.292,1.708 2.427,1.708 false 2.292,0.177 2.406,0.177 false 2.104,0.5 2.417,0.698 0.313,0.198 10 false *1 2.115,1.427 2.427,1.625 0.313,0.198 10 false *1 2.104,0.271 2.417,0.469 0.313,0.198 10 false *2 2.104,0.104 2.417,0.302 0.313,0.198 10 false *3 2.115,1.646 2.427,1.844 0.313,0.198 10 false *2 2.115,1.802 2.427,2 0.313,0.198 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.

·

Make sure that the conical spring is installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C306375
4.698,0.469 4.885,0.469 4.885,0.469 5.135,0.281 false 4.385,1.51 4.802,1.51 4.802,1.51 5.042,1.375 true 4.813,1.51 5.042,1.688 true 3.188,0.208 3.5,0.406 0.313,0.198 10 false *a 1.073,2.406 1.385,2.604 0.313,0.198 10 false *b 4.396,0.396 4.854,0.594 0.458,0.198 10 false SST 4.094,1.438 4.552,1.635 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09953-05010, 09528-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C287727
0,0 0,0 false
V100135

ATF


Coat the front differential pinion and front differential pinion thrust washer with ATF.


e.
C306382
2.729,2.802 2.563,2.802 2.563,2.802 2.563,2.385 true 1.771,0.427 2.229,0.625 0.458,0.198 10 false *a 2.792,2.729 3.25,2.927 0.458,0.198 10 false SST
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 5.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 6.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C306383
0,0 0,0 false
V100135

ATF


Coat the front No. 1 differential pinion shaft with ATF.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41342A 8.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C306384

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C306385

Using a chisel and hammer, stake the front differential case.


Hide 31105H 9.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.
C307977
1.417,1.292 0.677,2.302 0.677,2.302 1.385,1.521 true 1.885,1.896 2.677,1.896 true 2.448,2.115 2.594,2.115 2.594,2.115 2.594,1.896 false 0.365,2.25 0.719,2.448 0.354,0.198 10 false SST 2.74,1.823 3.073,2.01 0.333,0.188 10 true SST

Using SST and a hammer, install the transaxle case oil seal.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the transaxle case oil seal is installed in the correct direction.



Hide 31105D 10.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new front transaxle case oil seal with MP grease.


b.
C307978
0.542,0.344 0.677,0.344 0.677,0.344 0.927,0.74 true 2.198,1.938 2.49,1.938 false 0.219,0.281 0.677,0.479 0.458,0.198 10 false SST 1.885,1.875 2.344,2.073 0.458,0.198 10 false SST

Using SST and a hammer, install the front transaxle case oil seal.

SST
09308-14010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front transaxle case oil seal is installed in the correct direction.