35104V
1.REMOVE BREATHER PLUG HOSE
Using a screwdriver, remove the breather plug hose from the transaxle case sub-assembly.
| *1 | No. 1 Breather Plug (ATM) |
| *2 | Breather Plug Hose |
| *3 | No. 2 Breather Plug (ATM) |
| *4 | O-ring |
Using a screwdriver, remove the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) from the breather plug hose.
Using a screwdriver, remove the O-ring from the No. 2 breather plug (ATM).
84540
2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.
Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.
Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.
3.REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)
Remove the oil cooler tube union (outlet oil cooler union) from the transaxle case sub-assembly.
Remove the O-ring from the oil cooler tube union (outlet oil cooler union).
32921C
4.REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)
Remove the oil cooler tube union (inlet oil cooler union) from the transaxle case sub-assembly.
Remove the O-ring from the oil cooler tube union (inlet oil cooler union).
35104Q
5.REMOVE NO. 1 TRANSAXLE CASE PLUG
Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.
Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.
35104R
6.REMOVE NO. 2 TRANSAXLE CASE PLUG
Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.
Remove the gasket from each of the 3 No. 2 transaxle case plugs.
30500
7.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY
Support the automatic transaxle assembly with wooden blocks.
35106D
8.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY
Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.
Remove the gasket from the overflow plug.
Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.
Remove the 18 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the automatic transaxle assembly.
| *1 | Transmission Oil Cleaner Magnet |
Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.
35394
9.INSPECT TRANSMISSION OIL CLEANER MAGNET
35330
10.REMOVE VALVE BODY OIL STRAINER ASSEMBLY
Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.
| *1 | O-ring |
Remove the O-ring from the valve body oil strainer assembly.
35410
11.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
Remove the 11 bolts and transmission valve body assembly from transaxle case sub-assembly.
When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.
35145C
12.REMOVE TRANSAXLE CASE GASKET
Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.
13.INSPECT INPUT SHAFT SUB-ASSEMBLY END PLAY
35102
14.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY
Remove the refill plug from the rear transaxle cover sub-assembly.
Remove the gasket from the refill plug.
Remove the 3 No. 1 automatic transaxle case plugs from the rear transaxle cover sub-assembly.
Using a screwdriver, remove the 3 O-rings from the 3 No. 1 automatic transaxle case plugs.
Remove the 14 bolts from the rear transaxle cover sub-assembly.
Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.
Using a screwdriver, remove the 3 O-rings from the transaxle case sub-assembly.
Tape the screwdriver tip before use.
| *1 | Thrust Needle Roller Bearing |
| *2 | Thrust Needle Roller Race |
Remove the thrust needle roller bearing and thrust needle roller race from the rear transaxle cover sub-assembly.
| *1 | Oil Seal Ring |
Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.
Tape the screwdriver tip before use.
Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.
| *a | Turn |
| *b | Hold |
Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.
35635C
15.REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY
| *1 | Direct Multiple Disc Clutch Assembly |
| *2 | Thrust Needle Roller Bearing |
Remove the direct multiple disc clutch assembly from the transaxle case sub-assembly.
Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.
| *1 | Intermediate Shaft Oil Seal |
| *2 | O-ring |
Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.
Tape the screwdriver tip before use.
Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.
Tape the screwdriver tip before use.
35635E
16.REMOVE DIRECT MULTIPLE DISC CLUTCH SNAP RING
Using a screwdriver, remove the direct multiple disc clutch snap ring from the direct multiple disc clutch assembly.
Remove the No. 2 direct clutch piston from the direct multiple disc clutch assembly.
17.REMOVE NO. 2 CLUTCH DISC
| *1 | No. 2 Clutch Plate |
| *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Flange |
Remove the No. 2 clutch flange, 3 No. 2 clutch discs and 3 No. 2 clutch plates from the direct multiple disc clutch assembly.
18.INSPECT NO. 2 CLUTCH DISC
35730
19.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY
Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.
Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.
| *1 | Thrust Needle Roller Bearing |
| *2 | Thrust Needle Roller Race |
Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.
35730
20.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY
21.REMOVE NO. 1 CLUTCH DISC
Using 2 screwdrivers, remove the 2 snap rings from the direct multiple disc clutch assembly.
| *1 | No. 1 Clutch Flange |
| *2 | No. 1 Clutch Plate |
| *3 | No. 1 Clutch Disc |
Remove the No. 1 clutch flange, 4 No. 1 clutch discs and 4 No. 1 clutch plates from the direct multiple disc clutch assembly.
22.INSPECT NO. 1 CLUTCH DISC
35111C
23.REMOVE TRANSAXLE HOUSING
Remove the 20 bolts from the transaxle housing.
Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.
24.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE
Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.
35882A
25.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE
Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.
35035
26.REMOVE FRONT OIL PUMP ASSEMBLY
| *1 | Gasket |
Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.
Remove the gasket from the front oil pump assembly.
| *1 | Thrust Needle Roller Race |
Remove the thrust needle roller race from the underdrive planetary gear assembly.
| *1 | Thrust Needle Roller Bearing |
| *2 | O-ring |
Remove the thrust needle roller bearing from the counter drive gear nut.
Remove the O-ring from the transaxle case sub-assembly.
35301B
27.REMOVE FRONT OIL PUMP BODY O-RING
Remove the front oil pump body O-ring from the front oil pump body assembly.
35683B
28.REMOVE NO. 3 BRAKE DISC
| *1 | Snap Ring |
Using a screwdriver, remove the snap ring from the front oil pump assembly.
| *1 | No. 3 Brake Flange |
| *2 | No. 3 Brake Plate |
| *3 | No. 3 Brake Disc |
Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the front oil pump assembly.
35683B
29.INSPECT NO. 3 BRAKE DISC
34330
30.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY
Remove the underdrive planetary gear assembly from the front oil pump assembly.
35663
31.REMOVE NO. 3 BRAKE HUB
Remove the No. 3 brake hub from the underdrive planetary gear assembly.
| *1 | Thrust Needle Roller Race |
| *2 | Thrust Needle Roller Bearing |
Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.
35706V
32.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY
| *1 | Planetary Sun Gear Sub-assembly |
| *2 | Underdrive Planetary Gear Assembly |
| *3 | Snap Ring |
While expanding the snap ring with snap ring pliers, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.
Remove the snap ring from the underdrive planetary gear assembly.
34330
33.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY
35706V
34.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY
35701
35.REMOVE INPUT SHAFT SUB-ASSEMBLY
Remove the input shaft sub-assembly from the front oil pump assembly.
| *1 | Thrust Needle Roller Race |
| *2 | Thrust Needle Roller Bearing |
| *3 | Input Shaft Oil Seal Ring |
| *4 | Input Shaft Sub-assembly |
Remove the thrust needle roller bearing and thrust needle roller race from the input shaft sub-assembly.
Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft sub-assembly.
Tape the screwdriver tip before use.
34321
36.REMOVE UNDERDRIVE PLANETARY SUN GEAR
| *1 | Underdrive Planetary Sun Gear |
| *2 | Thrust Needle Roller Bearing |
Remove the underdrive planetary sun gear from the front oil pump assembly.
Remove the thrust needle roller bearing from the front oil pump assembly.
37.REMOVE NO. 1 BRAKE DISC
| *1 | Snap Ring |
| *2 | Brake Snap Ring Stopper |
Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.
| *1 | No. 1 Brake Flange |
| *2 | No. 1 Brake Plate |
| *3 | No. 1 Brake Disc |
Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the front oil pump assembly.
38.INSPECT NO. 1 BRAKE DISC
35608L
39.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Remove the 3 2nd brake piston return spring sub-assemblies from the front oil pump assembly.
35608L
40.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
35621F
41.REMOVE NO. 1 BRAKE PISTON
While holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.
| *1 | O-ring |
Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.
Tape the screwdriver tip before use.
41311
42.REMOVE FRONT DIFFERENTIAL CASE
Remove the front differential case from the transaxle case sub-assembly.
35782H
43.REMOVE COUNTER DRIVE GEAR NUT
Using SST and a hammer, release the staked part of the planetary gear assembly.
Turn the manual valve lever shaft sub-assembly 2 notches counterclockwise to set it to the P position as shown in the illustration.
Using SST, remove the counter drive gear nut from the front planetary gear assembly.
35783R
44.REMOVE COUNTER DRIVEN GEAR
Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.
Remove the counter driven gear from the transaxle case sub-assembly.
45.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING
| *a | Turn |
| *b | Hold |
Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.
46.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING
| *a | Turn |
| *b | Hold |
Using SST, remove the counter driven gear rear tapered roller bearing from the counter driven gear.
35558
47.REMOVE PAWL SHAFT CLAMP
Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.
35596
48.REMOVE PAWL STOPPER PLATE
Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.
35598
49.REMOVE PARKING LOCK SLEEVE
Remove the parking lock sleeve from the transaxle case sub-assembly.
35557
50.REMOVE PARKING LOCK PAWL
| *1 | Parking Lock Pawl Shaft |
| *2 | Parking Lock Pawl |
| *3 | Spring |
| *4 | Parking Lock Pawl Pin |
Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.
51.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE
Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case sub-assembly.
35790
52.REMOVE ONE-WAY CLUTCH ASSEMBLY
Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.
| *1 | One-way Clutch Assembly with Planetary Ring Gear |
| *2 | Thrust Needle Roller Bearing |
Remove the one-way clutch assembly with planetary ring gear from the transaxle case sub-assembly.
Remove the thrust needle roller bearing from the front planetary gear assembly.
35790
53.INSPECT ONE-WAY CLUTCH ASSEMBLY
35743K
54.REMOVE PLANETARY RING GEAR
| *1 | One-way Clutch Assembly |
| *2 | Outer Race Retainer |
| *3 | Planetary Ring Gear |
Remove the planetary ring gear from the one-way clutch assembly.
Remove the outer race retainer from the one-way clutch assembly.
35762E
55.REMOVE PLANETARY RING GEAR FLANGE
| *1 | Snap Ring |
| *2 | Planetary Ring Gear Flange |
| *3 | Planetary Ring Gear |
Using a screwdriver, remove the snap ring from the planetary ring gear.
Remove the planetary ring gear flange from the planetary ring gear.
35682A
56.REMOVE NO. 2 BRAKE DISC
Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.
| *1 | No. 2 Brake Flange |
| *2 | No. 2 Brake Plate |
| *3 | No. 2 Brake Disc |
Remove the No. 2 brake flange, 5 No. 2 brake discs and 5 No. 2 brake plates from the transaxle case sub-assembly.
35682A
57.INSPECT NO. 2 BRAKE DISC
35068C
58.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.
35068C
59.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
35622G
60.REMOVE NO. 2 BRAKE PISTON
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case sub-assembly.
| *1 | O-ring |
Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.
Tape the screwdriver tip before use.
35720
61.REMOVE FRONT PLANETARY GEAR ASSEMBLY
Using SST and a press, remove the front planetary gear assembly from the transaxle case sub-assembly.
35720
62.INSPECT FRONT PLANETARY GEAR ASSEMBLY
35782C
63.REMOVE COUNTER DRIVE GEAR
Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.
Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case sub-assembly.
As shown in the illustration, tighten 3 service bolts evenly to make a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and bearing inner race (front side).
| *a | Turn |
| *b | Hold |
Using SST, remove the bearing inner race (front side) from the counter drive gear.
35623
64.REMOVE NO. 3 BRAKE PISTON
Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.
| *1 | Brake Piston Return Spring |
| *2 | No. 3 Brake Piston |
Remove the brake piston return spring from the transaxle case sub-assembly.
Remove the No. 3 brake piston from the transaxle case sub-assembly.
35409
65.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY
Remove the bolt, cover and manual detent spring sub-assembly from the transaxle case sub-assembly.
35501
66.REMOVE PARKING LOCK ROD SUB-ASSEMBLY
Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.
Align the protrusions with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.
35506
67.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY
Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the manual valve lever shaft sub-assembly.
Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.
35506F
68.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.
Tape the screwdriver tip before use.