Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0077308 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E313899E07
0.396,2.448 2.531,2.729 2.135,0.281 10 false Steering Pad Switch Assembly 2.542,1.865 4.427,2.344 1.885,0.479 10 false Spiral Cable Sub-assembly 0.417,3.469 1.427,3.74 1.01,0.271 10 false from Battery 4.427,3.885 5.688,4.146 1.26,0.26 10 false to Main Body ECU 5.531,4.521 7.156,4.906 1.625,0.385 10 false Radio Receiver Assembly 3.438,3.635 4.01,3.927 0.573,0.292 10 false PANEL 2.604,4.156 3.125,4.479 0.521,0.323 10 false TAIL 3.177,0.667 3.667,0.958 0.49,0.292 10 false IL+2 3.177,1.417 3.635,1.615 0.458,0.198 10 false EAU 2.708,0.76 3.021,0.958 0.313,0.198 10 false z3 2.75,1.5 3.063,1.698 0.313,0.198 10 false z3 3.771,1.521 4.229,1.719 0.458,0.198 10 false I28 3.771,0.76 4.229,0.958 0.458,0.198 10 false I28 5.604,0.76 6.063,0.958 0.458,0.198 10 false I148 5.604,1.521 6.063,1.719 0.458,0.198 10 false I150 5.969,1.552 6.427,1.75 0.458,0.198 10 false SWG 5.99,0.771 6.448,0.969 0.458,0.198 10 false ILL+ 5.635,0.552 6.094,0.75 0.458,0.198 10 false 10 5.615,1.323 6.073,1.521 0.458,0.198 10 false 23 2.729,0.573 3.188,0.771 0.458,0.198 10 false 5 3.781,1.333 4.24,1.531 0.458,0.198 10 false 3 2.75,1.323 3.208,1.521 0.458,0.198 10 false 8 3.792,0.573 4.25,0.771 0.458,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I28 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I28-13 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch Assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH(for 4 Spoke)>REMOVAL


b.

Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.

E314622C02
4.083,1.604 4.208,0.938 false 4.042,0.271 4.49,0.833 false 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 3.917,1.646 4.354,1.885 0.438,0.24 10 false EAU 3.729,0.167 4.188,0.406 0.458,0.24 10 false IL+2
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



c.

Check that the switch illumination illuminates.

OK:

The steering pad switch illumination illuminates.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.
E263757C35
1.344,0.677 1.677,0.906 0.333,0.229 0.427,3.865 0.76,4.094 0.333,0.229 1.781,1.021 2,0.583 false 2.333,0.719 2.542,0.969 false 1.042,4.26 1.229,3.844 false 1.792,4.24 1.521,3.76 false 0.24,0.188 0.625,0.479 0.385,0.292 10 false *a 1.177,0.25 1.563,0.542 0.385,0.292 10 false *b 0.354,3.563 0.74,3.854 0.385,0.292 10 false *c 1.552,1.052 2.167,1.25 0.615,0.198 10 false IL+2 2.5,1 2.885,1.24 0.385,0.24 10 false EAU 1.438,0.708 1.75,0.906 0.313,0.198 10 false z3 0.917,4.281 1.302,4.521 0.385,0.24 10 false EAU 1.646,4.26 2.26,4.458 0.615,0.198 10 false IL+2 0.51,3.896 0.969,4.094 0.458,0.198 10 false I28
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z3-8 (EAU) - I28-3 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Always 3 Ω or less
z3-8 (EAU) - I28-3 (EAU) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the I150 radio receiver assembly connector.


b.

Disconnect the I28 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-23 (SWG) - I28-3 (EAU) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I148 radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I148-10 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR