CHECK HEADLIGHT LEVELING ECU ASSEMBLY
Disconnect the A78 headlight leveling ECU assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A78-1 (IG) - Body ground | LG - Body ground | IG power supply | Engine switch off | Below 1 V |
| Engine switch on (IG) | 11 to 14 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A78-9 (E1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the A78 headlight leveling ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A78-21 (SGR) - Body ground | V - Body ground | Rear height control sensor sub-assembly ground | Always | Below 1 Ω |
| A78-23 (RH-) - Body ground | G - Body ground | Headlight leveling motor RH ground | Always | Below 1 Ω |
| A78-24 (LH-) - Body ground | B - Body ground | Headlight leveling motor LH ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A78-3 (B2) - Body ground | G - Body ground | Low beam headlight signal input | Low beam headlights on | Below 1.5 V |
| Low beam headlights off | 5 V or higher | |||
| A78-5 (SPDL) - Body ground | V - Body ground | Initialization signal input | Terminals LVL and GND of DLC3 connected | Below 1 V |
| Terminals LVL and GND of DLC3 not connected | 4.5 to 5.5 V | |||
| A78-6 (WNG) - Body ground | SB - Body ground | Warning message drive output | Warning message on | Below 1 V |
| Warning message off | 11 to 14 V | |||
| A78-10 (RH+) - Body ground | R - Body ground | Headlight leveling motor RH power supply | Engine switch off | Below 1 V |
| Engine switch on (IG) | 11 to 14 V | |||
| A78-11 (LH+) - Body ground | Y - Body ground | Headlight leveling motor LH power supply | Engine switch off | Below 1 V |
| Engine switch on (IG) | 11 to 14 V | |||
| A78-12 (SBR) - Body ground | B - Body ground | Rear height control sensor sub-assembly power supply | Engine switch off | Below 1 V |
| Engine switch on (IG) | 4.75 to 5.25 V | |||
| A78-16 (SPDR) - Body ground | L - Body ground | Vehicle speed signal input | Vehicle driven at approx. 20 km/h (12 mph) | Pulse generation
(See waveform 1) |
| A78-17 (RHT) - Body ground | W - Body ground | Headlight leveling motor RH operation signal input | With low beam headlights on, vehicle height not changed | Below 1 V |
| With low beam headlights on, vehicle height changed and maintained for more than 3 seconds | 1.0 to 14.4 V | |||
| A78-18 (LHT) - Body ground | LG - Body ground | Headlight leveling motor LH operation signal input | With low beam headlights on, vehicle height not changed | Below 1 V |
| With low beam headlights on, vehicle height changed and maintained for more than 3 seconds | 1.0 to 14.4 V | |||
| A78-19 (SHRL) - Body ground | R - Body ground | Rear height control sensor sub-assembly signal input | Engine switch off | Below 1 V |
| Engine switch on (IG) | 0.5 to 4.5 V |
If the result is not as specified, the headlight leveling ECU assembly may have a malfunction.
Waveform 1
| Item | Content |
|---|---|
| Tool setting | 2 V/DIV., 2 ms./DIV. |
| Vehicle condition | Wheel being rotated |