Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074558 REAR VIEW MONITOR SYSTEM Y

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the rear view monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The rear view monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause
Both of the following conditions are met:
·

The problem symptom indicates a rear view monitor display malfunction and the problem symptom cannot be reproduced.

·

DTC C1622 is output as "Hist" only.*


The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.

*: DTCs output as "Hist" will not be output again after DTCs are cleared.




Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC*
4.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs. Try to reproduce the DTCs by simulating the conditions indicated by the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

5.PROBLEM SYMPTOM CONFIRMATION

B

10.ADJUST, REPAIR OR REPLACE
5.PROBLEM SYMPTOM CONFIRMATION
Result:
Result Proceed to
Symptom does not occur A
Symptom occurs B



A

6.SYMPTOM SIMULATION

B

7.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM
6.SYMPTOM SIMULATION

Result:
Proceed to
NEXT



NEXT

7.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM
7.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM
a.

Result:
Result Proceed to
Symptom does not appear A
Symptom appears B



A

8.PROBLEM SYMPTOMS TABLE

B

8.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B




A

9.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

10.ADJUST, REPAIR OR REPLACE
9.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END