OVERALL CAN BUS DIAGRAM (for LHD)
The CAN communication system is composed of 3 buses.
| 1 | Combination Meter Assembly
(for V Bus) |
2 | Airbag Sensor Assembly
(for V Bus) |
| 3 | Main Body ECU (Multiplex Network Body ECU)
(for V Bus and Sub Bus 1) |
4 | DLC3
(for V Bus) |
| 5 | Power Steering ECU Assembly
(for V Bus) |
6 | Steering Sensor
(for V Bus) |
| 7 | Air Conditioning Amplifier Assembly
(for V Bus) |
8 | Smart Key ECU Assembly
(Certification ECU) (for V Bus) |
| 9 | Brake Actuator Assembly
(for V Bus) |
10 | ·
Navigation Receiver Assembly (for Navigation Receiver Type) ·
Radio and Display Receiver Assembly (for Radio and Display Type) (for V Bus) |
| 11 | Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System) (for V Bus) |
12 | Network Gateway ECU
(w/ Parking Assist Monitor System) (for V Bus and Sub Bus 2) |
| 13 | ECM
(for V Bus) |
14 | Position Control ECU and Switch Assembly (for Driver Side)
(w/ Seat Position Memory System) (for Sub Bus 1) |
| 15 | Outer Mirror Control ECU Assembly
(for Driver Side) (w/ Seat Position Memory System) (for Sub Bus 1) |
16 | Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System) (for Sub Bus 1) |
| 17 | CAN No. 5 Junction Connector
(w/ Seat Position Memory System) (for Sub Bus 1) |
18 | Rear Television Camera Assembly
(w/ Parking Assist Monitor System) (for Sub Bus 2) |
| 19 | CAN No. 8 Junction Connector
(w/ Parking Assist Monitor System) (for Sub Bus 2) |
- | - |
The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
The network gateway ECU functions as a gateway between the V bus and sub bus 2.
Refer to the following bus wiring diagrams for details.
V BUS (for LHD)
The CAN communication system connects to other networks via ECUs that function as a gateway.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
SUB BUS 1 (for LHD) (w/ Seat Position Memory System)
SUB BUS 2 (for LHD) (w/ Parking Assist Monitor System)
OVERALL CAN BUS DIAGRAM (for RHD)
The CAN communication system is composed of 3 buses.
| 1 | ECM
(for V Bus) |
2 | Airbag Sensor Assembly
(for V Bus) |
| 3 | Main Body ECU
(Multiplex Network Body ECU) (for V Bus and Sub Bus 1) |
4 | Air Conditioning Amplifier Assembly
(for V Bus) |
| 5 | Power Steering ECU Assembly
(for V Bus) |
6 | ·
Navigation Receiver Assembly (for Navigation Receiver Type) ·
Radio and Display Receiver Assembly (for Radio and Display Type) (for V Bus) |
| 7 | Smart Key ECU Assembly (Certification ECU)
(for V Bus) |
8 | Steering Sensor
(for V Bus) |
| 9 | DLC3
(for V Bus) |
10 | Brake Actuator Assembly
(for V Bus) |
| 11 | Clearance Warning ECU Assembly
(for V Bus) |
12 | Network Gateway ECU
(for V Bus and Sub Bus 2) |
| 13 | Combination Meter Assembly
(for V Bus) |
14 | Outer Mirror Control ECU Assembly
(for Front Passenger Side) (w/ Seat Position Memory System) (for Sub Bus 1) |
| 15 | Outer Mirror Control ECU Assembly
(for Driver Side) (w/ Seat Position Memory System) (for Sub Bus 1) |
16 | Position Control ECU and Switch Assembly (for Driver Side)
(w/ Seat Position Memory System) (for Sub Bus 1) |
| 17 | CAN No. 4 Junction Connector
(w/ Seat Position Memory System) (for Sub Bus 1) |
18 | Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System) (for Sub Bus 2) |
| 19 | Lane Departure Warning Camera
(w/ Blind Spot Monitor System) (for Sub Bus 2) |
20 | Rear Television Camera Assembly
(for Sub Bus 2) |
| 21 | CAN No. 8 Junction Connector
(for Sub Bus 2) |
- | - |
The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
The network gateway ECU functions as a gateway between the V bus and sub bus 2.
Refer to the following bus wiring diagrams for details.
V BUS (for RHD)
The CAN communication system connects to other networks via ECUs that function as a gateway.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
SUB BUS 1 (for RHD) (w/ Seat Position Memory System)
SUB BUS 2 (for RHD)