Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.04–2016.05
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Turn the engine switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the engine switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN NO. 1 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 1 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C248100C01
2.302,0.771 2.896,0.771 2.896,0.771 2.896,1.167 false 2.719,0.49 3.177,0.49 3.177,0.49 3.177,1.167 false 3.146,0.208 3.448,0.208 3.448,0.208 3.448,1.167 false 2.302,1.99 2.896,1.99 2.896,1.99 2.896,1.354 false 2.719,2.271 3.177,2.271 3.177,2.271 3.177,1.354 false 3.146,2.563 3.448,2.563 3.448,2.563 3.448,1.354 false 5.156,0.646 4.271,0.646 4.271,0.646 4.271,1.156 false 5.573,0.875 4.552,0.875 4.552,0.875 4.552,1.156 false 4.729,0.417 4,0.417 4,0.417 4,1.156 false 4.583,0.198 3.729,0.198 3.729,0.198 3.729,1.156 false 5.146,2.104 4.26,2.104 4.26,2.104 4.26,1.354 false 5.563,1.885 4.542,1.885 4.542,1.885 4.542,1.354 false 4.719,2.333 3.99,2.333 3.99,2.333 3.99,1.354 false 4.573,2.563 3.719,2.563 3.719,2.563 3.719,1.354 false 0.156,0.125 0.323,0.281 0.167,0.156 10 false *a 2.615,0.135 3.281,0.354 0.667,0.219 10 false CANH*d 2.188,0.406 2.865,0.677 0.677,0.271 10 false CANH*c 1.76,0.698 2.479,0.969 0.719,0.271 10 false CANH*b 1.771,1.917 2.458,2.167 0.688,0.25 10 false CANL*b 2.208,2.188 2.865,2.417 0.656,0.229 10 false CANL*c 2.625,2.49 3.281,2.75 0.656,0.26 10 false CANL*d 4.625,0.115 5.26,0.354 0.635,0.24 10 false CANH*e 4.792,0.333 5.458,0.573 0.667,0.24 10 false CANH*f 5.208,0.563 5.917,0.844 0.708,0.281 10 false CANH*g 5.198,2.031 5.854,2.271 0.656,0.24 10 false CANL*g 4.771,2.26 5.5,2.51 0.729,0.25 10 false CANL*f 4.625,2.49 5.271,2.708 0.646,0.219 10 false CANL*e 5.625,0.792 6.25,1.052 0.625,0.26 10 false CANH*h 5.635,1.802 6.25,2.052 0.615,0.25 10 false CANL*h
*a Component with harness connected
(CAN No. 1 Junction Connector)
*b to Main Body ECU
(Multiplex Network Body ECU)
(for V Bus)
*c to Steering Sensor
(for V Bus)
*d to Airbag Sensor Assembly
(for V Bus)
*e to DLC3
(for V bus)
*f to Power Steering ECU Assembly
(for V Bus)
*g to Combination Meter Assembly
(for V Bus)
*h to CAN No. 2 Junction Connector
(for V Bus)



ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I95-1 (CANH) P Main body ECU (multiplex network body ECU)
(for V bus)
I95-2 (CANL) W
I97-1 (CANH) V Steering sensor
(for V bus)
I97-2 (CANL) W
I103-1 (CANH) Y Airbag sensor assembly
(for V bus)
I103-2 (CANL) W
I96-1 (CANH) L DLC3
(for V bus)
I96-2 (CANL) W
I100-1 (CANH) G Power steering ECU assembly
(for V bus)
I100-2 (CANL) W
I94-1 (CANH) R Combination meter assembly
(for V bus)
I94-2 (CANL) W
I93-1 (CANH) B CAN No. 2 junction connector
(for V bus)
I93-2 (CANL) W




CAN NO. 1 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 1 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C248103C05
2.021,0.771 2.625,0.771 2.625,0.771 2.625,1.167 false 2.448,0.49 2.896,0.49 2.896,0.49 2.896,1.167 false 2.875,0.208 3.167,0.208 3.167,0.208 3.167,1.167 false 2.021,2.01 2.625,2.01 2.625,2.01 2.625,1.365 false 2.448,2.292 2.896,2.292 2.896,2.292 2.896,1.365 false 2.875,2.573 3.167,2.573 3.167,2.573 3.167,1.365 false 4.865,0.656 3.99,0.656 3.99,0.656 3.99,1.167 false 5.271,0.885 4.25,0.885 4.25,0.885 4.25,1.167 false 4.448,0.427 3.719,0.427 3.719,0.427 3.719,1.167 false 4.292,0.208 3.448,0.208 3.448,0.208 3.448,1.167 false 4.865,2.115 3.99,2.115 3.99,2.115 3.99,1.365 false 5.271,1.896 4.25,1.896 4.25,1.896 4.25,1.365 false 4.438,2.344 3.708,2.344 3.708,2.344 3.708,1.365 false 4.281,2.573 3.438,2.573 3.438,2.573 3.438,1.365 false 4.573,1.198 4.854,1.115 4.854,1.115 5.052,1.115 false 4.583,1.323 4.854,1.427 4.854,1.427 5.042,1.427 false 0.146,0.083 0.417,0.344 0.271,0.26 10 false *a 2.344,0.125 2.979,0.417 0.635,0.292 10 false CANH*d 1.917,0.406 2.531,0.635 0.615,0.229 10 false CANH*c 1.479,0.688 2.135,0.906 0.656,0.219 10 false CANH*b 1.49,1.927 2.167,2.104 0.677,0.177 10 false CANL*b 1.938,2.208 2.563,2.396 0.625,0.188 10 false CANL*c 2.354,2.49 3.073,2.719 0.719,0.229 10 false CANL*d 4.344,0.125 5.021,0.385 0.677,0.26 10 false CANH*e 4.49,0.344 5.167,0.594 0.677,0.25 10 false CANH*f 4.927,0.563 5.625,0.771 0.698,0.208 10 false CANH*g 4.896,2.042 5.531,2.313 0.635,0.271 10 false CANL*g 4.469,2.26 5.083,2.469 0.615,0.208 10 false CANL*f 4.313,2.49 4.948,2.688 0.635,0.198 10 false CANL*e 5.333,0.792 5.958,1.042 0.625,0.25 10 false CANH*h 5.313,1.813 6.031,2.094 0.719,0.281 10 false CANL*h 5.073,1.052 5.719,1.292 0.646,0.24 10 false CANH*i 5.073,1.354 5.74,1.615 0.667,0.26 10 false CANL*i
*a Component with harness connected
(CAN No. 1 Junction Connector)
*b to Network Gateway ECU
(for V Bus)
*c Main Body ECU
(Multiplex Network Body ECU)
(for V Bus)
*d to Air Conditioning Amplifier Assembly
(for V Bus)
*e to Airbag Sensor Assembly
(for V Bus)
*f to Power Steering ECU Assembly
(for V Bus)
*g to ECM
(for V Bus)
*h
·

to Navigation Receiver Assembly*1

·

to Radio and Display Receiver Assembly*2


(for V Bus)
*i to CAN No. 2 Junction Connector
(for V Bus)
- -


*1: for Navigation Receiver Type

*2: for Radio and Display Type


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I161-1 (CANH) BE Network gateway ECU
(for V bus)
I161-2 (CANL) W
I95-1 (CANH) P Main body ECU (multiplex network body ECU)
(for V bus)
I95-2 (CANL) W
I102-1 (CANH) V Air conditioning amplifier assembly
(for V bus)
I102-2 (CANL) W
I103-1 (CANH) Y Airbag sensor assembly
(for V bus)
I103-2 (CANL) W
I100-1 (CANH) L Power steering ECU assembly
(for V bus)
I100-2 (CANL) W
I104-1 (CANH) G ECM
(for V bus)
I104-2 (CANL) W
I107-1 (CANH) R
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


(for V bus)
I107-2 (CANL) W
I93-1 (CANH) B CAN No. 2 junction connector
(for V bus)
I93-2 (CANL) W

*1: for Navigation Receiver Type

*2: for Radio and Display Type




CAN NO. 2 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 2 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C239444C02
0.147,0.127 0.31,0.283 0.163,0.156 10 *a 4.343,0.127 4.89,0.283 0.547,0.156 10 CANH*f 4.763,0.351 5.31,0.508 0.547,0.156 10 CANH*g 5.183,0.576 5.731,0.732 0.547,0.156 10 CANH*h 5.183,2.044 5.731,2.201 0.547,0.156 10 CANL*h 4.763,2.269 5.31,2.425 0.547,0.156 10 CANL*g 4.343,2.493 4.89,2.649 0.547,0.156 10 CANL*f 5.147,0.651 4.27,0.651 4.27,0.651 4.27,1.166 false 5.604,0.8 6.151,0.956 0.547,0.156 10 CANH*i 5.567,0.875 4.55,0.875 4.55,0.875 4.55,1.166 false 4.727,0.426 3.998,0.426 3.998,0.426 3.998,1.166 false 4.306,0.201 3.729,0.201 3.729,0.201 3.729,1.166 false 5.147,2.111 4.27,2.111 4.27,2.111 4.27,1.355 false 5.604,1.82 6.151,1.977 0.547,0.156 10 CANL*i 5.567,1.887 4.55,1.887 4.55,1.887 4.55,1.355 false 4.727,2.337 3.998,2.337 3.998,2.337 3.998,1.355 false 4.306,2.563 3.729,2.563 3.729,2.563 3.729,1.355 false 2.299,0.127 2.847,0.283 0.547,0.156 10 CANH*e 1.879,0.351 2.427,0.508 0.547,0.156 10 CANH*d 1.459,0.576 2.006,0.732 0.547,0.156 10 CANH*c 1.459,2.044 2.006,2.201 0.547,0.156 10 CANL*c 1.879,2.269 2.427,2.425 0.547,0.156 10 CANL*d 2.299,2.493 2.847,2.649 0.547,0.156 10 CANL*e 2.03,0.651 2.907,0.651 2.907,0.651 2.907,1.166 false 1.039,0.8 1.586,0.956 0.547,0.156 10 CANH*b 1.609,0.875 2.627,0.875 2.627,0.875 2.627,1.166 false 2.45,0.426 3.179,0.426 3.179,0.426 3.179,1.166 false 2.87,0.201 3.448,0.201 3.448,0.201 3.448,1.166 false 2.03,2.111 2.907,2.111 2.907,2.111 2.907,1.355 false 1.039,1.82 1.586,1.977 0.547,0.156 10 CANL*b 1.609,1.887 2.627,1.887 2.627,1.887 2.627,1.355 false 2.45,2.337 3.179,2.337 3.179,2.337 3.179,1.355 false 2.87,2.563 3.448,2.563 3.448,2.563 3.448,1.355 false
*a Component with harness connected
(CAN No. 2 Junction Connector)
*b to Brake Actuator Assembly
(for V Bus)
*c
·

to Navigation Receiver Assembly*2

·

to Radio and Display Receiver Assembly*3


(for V Bus)
*d to Network Gateway ECU*4
(for V Bus)
*e to Clearance Warning ECU Assembly*1
(for V Bus)
*f to Smart Key ECU Assembly
(Certification ECU)
(for V Bus)
*g to ECM
(for V Bus)
*h to Air Conditioning Amplifier Assembly
(for V Bus)
*i to CAN No. 1 Junction Connector
(for V Bus)
- -


*1: w/ Toyota Parking Assist-sensor System

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Parking Assist Monitor System


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I105-1 (CANH) Y Brake actuator assembly
(for V bus)
I105-2 (CANL) W
I107-1 (CANH) R
·

Navigation receiver assembly*2

·

Radio and display receiver assembly*3


(for V bus)
I107-2 (CANL) W
I161-1 (CANH) G Network gateway ECU*4
(for V bus)
I161-2 (CANL) W
I111-1 (CANH) BE Clearance warning ECU assembly*1
(for V bus)
I111-2 (CANL) W
I106-1 (CANH) L Smart key ECU assembly (certification ECU)
(for V bus)
I106-2 (CANL) W
I104-1 (CANH) P ECM
(for V bus)
I104-2 (CANL) W
I102-1 (CANH) V Air conditioning amplifier assembly
(for V bus)
I102-2 (CANL) W
I101-1 (CANH) B CAN No. 1 junction connector
(for V bus)
I101-2 (CANL) W

*1: w/ Toyota Parking Assist-sensor System

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Parking Assist Monitor System




CAN NO. 2 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 2 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C248100C01
2.302,0.771 2.896,0.771 2.896,0.771 2.896,1.167 false 2.719,0.49 3.177,0.49 3.177,0.49 3.177,1.167 false 3.146,0.208 3.448,0.208 3.448,0.208 3.448,1.167 false 2.302,1.99 2.896,1.99 2.896,1.99 2.896,1.354 false 2.719,2.271 3.177,2.271 3.177,2.271 3.177,1.354 false 3.146,2.563 3.448,2.563 3.448,2.563 3.448,1.354 false 5.156,0.646 4.271,0.646 4.271,0.646 4.271,1.156 false 5.573,0.875 4.552,0.875 4.552,0.875 4.552,1.156 false 4.729,0.417 4,0.417 4,0.417 4,1.156 false 4.583,0.198 3.729,0.198 3.729,0.198 3.729,1.156 false 5.146,2.104 4.26,2.104 4.26,2.104 4.26,1.354 false 5.563,1.885 4.542,1.885 4.542,1.885 4.542,1.354 false 4.719,2.333 3.99,2.333 3.99,2.333 3.99,1.354 false 4.573,2.563 3.719,2.563 3.719,2.563 3.719,1.354 false 0.156,0.125 0.323,0.281 0.167,0.156 10 false *a 2.615,0.135 3.281,0.354 0.667,0.219 10 false CANH*d 2.188,0.406 2.865,0.677 0.677,0.271 10 false CANH*c 1.76,0.698 2.479,0.969 0.719,0.271 10 false CANH*b 1.771,1.917 2.458,2.167 0.688,0.25 10 false CANL*b 2.208,2.188 2.865,2.417 0.656,0.229 10 false CANL*c 2.625,2.49 3.281,2.75 0.656,0.26 10 false CANL*d 4.625,0.115 5.26,0.354 0.635,0.24 10 false CANH*e 4.792,0.333 5.458,0.573 0.667,0.24 10 false CANH*f 5.208,0.563 5.917,0.844 0.708,0.281 10 false CANH*g 5.198,2.031 5.854,2.271 0.656,0.24 10 false CANL*g 4.771,2.26 5.5,2.51 0.729,0.25 10 false CANL*f 4.625,2.49 5.271,2.708 0.646,0.219 10 false CANL*e 5.625,0.792 6.25,1.052 0.625,0.26 10 false CANH*h 5.635,1.802 6.25,2.052 0.615,0.25 10 false CANL*h
*a Component with harness connected
(CAN No. 2 Junction Connector)
*b to Clearance Warning ECU Assembly
(for V Bus)
*c to Steering Sensor
(for V Bus)
*d to Brake Actuator Assembly
(for V Bus)
*e to Smart Key ECU Assembly
(Certification ECU)
(for V Bus)
*f to DLC3
(for V Bus)
*g to Combination Meter Assembly
(for V Bus)
*h to CAN No. 1 Junction Connector
(for V Bus)



ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I112-1 (CANH) BE Clearance warning ECU assembly
(for V bus)
I112-2 (CANL) W
I97-1 (CANH) V Steering sensor
(for V bus)
I97-2 (CANL) W
I105-1 (CANH) Y Brake actuator assembly
(for V bus)
I105-2 (CANL) W
I106-1 (CANH) L Smart key ECU assembly (certification ECU)
(for V bus)
I106-2 (CANL) W
I96-1 (CANH) G DLC3
(for V bus)
I96-2 (CANL) W
I94-1 (CANH) R Combination meter assembly
(for V bus)
I94-2 (CANL) W
I101-1 (CANH) B CAN No. 1 junction connector
(for V bus)
I101-2 (CANL) W




CAN NO. 3 JUNCTION CONNECTOR (for LHD) (w/ Seat Position Memory System)


a.

Check the CAN No. 3 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C252631C01
0.103,0.077 0.507,0.342 0.403,0.264 10 *a 2.308,0.562 2.879,0.715 0.571,0.153 10 CANH*b 2.308,1.872 2.879,2.025 0.571,0.153 10 CANL*b 3.455,1.16 3.455,0.635 3.455,0.635 2.87,0.635 false 3.449,1.356 3.449,1.94 3.449,1.94 2.865,1.94 false 2.683,0.235 3.254,0.388 0.571,0.153 10 CANH*c 2.683,2.212 3.254,2.365 0.571,0.153 10 CANL*c 4.268,0.338 4.839,0.491 0.571,0.153 10 CANH*d 4.268,2.157 4.839,2.31 0.571,0.153 10 CANL*d 4.695,0.721 5.265,0.874 0.571,0.153 10 CANH*e 4.695,1.845 5.265,1.998 0.571,0.153 10 CANL*e 3.241,0.305 3.729,0.305 3.729,0.305 3.729,1.162 false 3.732,1.36 3.732,2.295 3.732,2.295 3.24,2.295 false 3.979,1.16 3.979,0.407 3.979,0.407 4.248,0.407 false 3.982,1.356 3.982,2.228 3.982,2.228 4.25,2.228 false 4.259,1.158 4.259,0.792 4.259,0.792 4.671,0.792 false 4.257,1.353 4.257,1.907 4.257,1.907 4.667,1.907 false
*a Component with harness connected
(CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
(for Sub Bus 1)
*c to Position Control ECU and Switch Assembly (for Driver Side)
(for Sub Bus 1)
*d to Outer Mirror Control ECU Assembly
(for Driver Side)
(for Sub Bus 1)
*e to Main Body ECU
(Multiplex Network Body ECU)
(for Sub Bus 1)
- -




b.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I116-1 (CANH) R Main body ECU
(multiplex network body ECU)
(for Sub bus 1)
I116-2 (CANL) GR
I171-1 (CANH) G Outer mirror control ECU assembly (for driver side)
(for Sub bus 1)
I171-2 (CANL) GR
I173-1 (CANH) L Position control ECU and switch assembly (for driver side)
(for Sub bus 1)
I173-2 (CANL) GR
I117-1 (CANH) Y CAN No. 4 junction connector
(for Sub bus 1)
I117-2 (CANL) GR



CAN NO. 3 JUNCTION CONNECTOR (for RHD) (w/ Seat Position Memory System)


a.

Check the CAN No. 3 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C247999C07
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.531 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN No. 3 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 3 Junction Connector)




b.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I162-1 (CANH) R Main body ECU
(multiplex network body ECU)
I162-2 (CANL) GR
I163-1 (CANH) G Outer mirror control ECU assembly (for front passenger side)
I163-2 (CANL) GR
I166-1 (CANH) Y CAN No. 4 junction connector
I166-2 (CANL) GR



CAN NO. 4 JUNCTION CONNECTOR (for LHD) (w/ Seat Position Memory System)


a.

Check the CAN No. 4 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C249338C02
2.688,0.635 2.896,0.635 2.896,0.635 2.896,1.167 false 2.938,0.313 3.167,0.313 3.167,0.313 3.167,1.167 false 3.625,0.635 3.448,0.635 3.448,0.635 3.448,1.167 false 3.667,2.313 3.448,2.313 3.448,2.313 3.448,1.354 false 2.625,2.021 2.896,2.021 2.896,2.021 2.896,1.365 false 2.906,2.344 3.167,2.344 3.167,2.344 3.167,1.354 false 2.115,0.552 2.719,0.719 0.604,0.167 10 CANH*b 2.052,1.927 2.656,2.094 0.604,0.167 10 CANL*b 2.354,0.219 2.958,0.385 0.604,0.167 10 CANH*c 2.323,2.26 2.927,2.427 0.604,0.167 10 CANL*c 3.708,0.552 4.313,0.719 0.604,0.167 10 CANH*d 3.729,2.229 4.333,2.396 0.604,0.167 10 CANL*d 0.125,0.052 0.333,0.219 0.208,0.167 10 *a
*a Component with harness connected
(CAN No. 4 Junction Connector)
*b to Outer Mirror Control ECU Assembly
(for Front Passenger Side)
(for Sub Bus 1)
*c to CAN No. 5 Junction Connector
(for Sub Bus 1)
*d to CAN No. 3 Junction Connector
(for Sub Bus 1)




b.

Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I172-1 (CANH) P Outer mirror control ECU assembly (for front passenger side)
I172-2 (CANL) GR
I121-1 (CANH) V CAN No. 5 junction connector
I121-2 (CANL) GR
I120-1 (CANH) Y CAN No. 3 junction connector
I120-2 (CANL) GR



CAN NO. 4 JUNCTION CONNECTOR (for RHD) (w/ Seat Position Memory System)


a.

Check the CAN No. 4 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C248000C06
6.188,1.74 6.406,1.167 6.406,1.167 6.521,1.167 false 1.135,4.688 1.573,4.542 false 1.583,5.021 1.146,4.865 false 0.146,0.125 0.594,0.448 0.448,0.323 10 false *1 1.365,0.677 1.813,1 0.448,0.323 10 false *a 4.438,0.677 4.885,1 0.448,0.323 10 false *b 6.563,1.073 6.75,1.292 0.188,0.219 10 false *c 0.563,4.052 1.01,4.375 0.448,0.323 10 false *d 1.594,4.458 2.125,4.688 0.531,0.229 10 false CANH 1.594,4.958 2.125,5.188 0.531,0.229 10 false CANL 4.615,4.844 5.073,5.052 0.458,0.208 10 false I164 4.615,4.469 5.073,4.677 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.198 5.073,5.406 0.458,0.208 10 false I167
*1 CAN No. 4 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 4 Junction Connector)




b.

Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I168-1 (GND) W-B Body ground
I167-1 (CANH) Y CAN No. 3 junction connector
I167-2 (CANL) GR
I165-1 (CANH) BE Position control ECU and switch assembly (for driver side)
I165-2 (CANL) GR
I164-1 (CANH) P Outer mirror control ECU assembly (for driver side)
I164-2 (CANL) GR



CAN NO. 5 JUNCTION CONNECTOR (for LHD) (w/ Seat Position Memory System)


a.

Check the CAN No. 5 junction connector.

i.
C183982C16
1.781,2.052 2.229,2.313 0.448,0.26 0.948,0.865 0.646,0.865 0.646,0.865 0.646,2.188 false 1.24,1.198 0.938,1.198 0.938,1.198 0.938,2.177 false 0.177,0.104 0.333,0.281 0.156,0.177 10 false *a 1,0.771 1.573,0.927 0.573,0.156 10 false CANH*b 1.292,1.115 1.854,1.271 0.563,0.156 10 false CANL*b 1.865,2.104 2.188,2.271 0.323,0.167 10 false I123
*a Rear view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 4 Junction Connector
(for Sub Bus 1)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
I123-3 (CANH) V CAN No. 4 junction connector
(for Sub bus 1)
I123-2 (CANL) GR




CAN NO. 6 JUNCTION CONNECTOR (w/ Parking Assist Monitor System)


a.

Check the CAN No. 6 junction connector.

i.
C238890C95
0.365,1.146 0.781,1.385 0.417,0.24 2.281,0.271 1.958,0.271 1.958,0.271 1.958,1.365 true 2.406,0.51 2.083,0.51 2.083,0.51 2.083,1.354 true 2.625,0.771 2.302,0.771 2.302,0.771 2.302,1.354 true 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 true 1.125,1.885 1.958,1.885 1.958,1.885 1.958,1.573 true 1.927,2.063 2.083,2.063 2.083,2.063 2.083,1.573 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.344,0.177 2.896,0.333 0.552,0.156 10 false CANH*b 2.49,0.417 3.042,0.573 0.552,0.156 10 false CANH*c 2.688,0.688 3.24,0.844 0.552,0.156 10 false CANH*d 2.677,1.792 3.229,1.948 0.552,0.156 10 false CANL*d 0.573,1.792 1.125,1.948 0.552,0.156 10 false CANL*b 1.344,1.969 1.896,2.125 0.552,0.156 10 false CANL*c 0.448,1.188 0.771,1.354 0.323,0.167 10 false O31
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
(for Sub Bus 2)
*c to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
(for Sub Bus 2)
*d to CAN No. 10 Junction Connector
(for Sub Bus 2)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 6 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
O31-8 (CANH) G CAN No. 7 junction connector
(for Sub bus 2)
O31-19 (CANL) B
O31-9 (CANH) R Blind spot monitor sensor RH*
(for Sub bus 2)
O31-20 (CANL) B
O31-11 (CANH) V CAN No. 10 junction connector
(for Sub bus 2)
O31-22 (CANL) B

*: w/ Blind Spot Monitor System




CAN NO. 7 JUNCTION CONNECTOR (w/ Parking Assist Monitor System)


a.

Check the CAN No. 7 junction connector.

i.
C238890C87
1.479,0.094 1.896,0.333 0.417,0.24 0.792,0.823 1.021,0.823 1.021,0.823 1.271,1.365 false 0.896,0.479 1.146,0.479 1.146,0.479 1.385,1.375 false 1.052,1.885 1.281,1.885 1.281,1.885 1.281,1.573 false 1.771,1.927 1.385,1.927 1.385,1.927 1.385,1.573 false 0.729,1.177 0.906,1.177 0.906,1.177 1.125,1.406 true 0.74,1.531 1.135,1.531 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.167,1.104 0.719,1.26 0.552,0.156 10 false CANH*b 0.26,0.75 0.813,0.906 0.552,0.156 10 false CANH*c 0.344,0.417 0.896,0.573 0.552,0.156 10 false CANH*d 1.844,1.854 2.396,2.01 0.552,0.156 10 false CANL*d 0.198,1.458 0.75,1.615 0.552,0.156 10 false CANL*b 0.521,1.802 1.073,1.958 0.552,0.156 10 false CANL*c 1.573,0.125 1.844,0.292 0.271,0.167 10 false T17
*a Front view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 8 Junction Connector
(for Sub Bus 2)
*c to Rear Television Camera Assembly
(for Sub Bus 2)
*d to CAN No. 6 Junction Connector
(for Sub Bus 2)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 7 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
T17-1 (CANH) L CAN No. 8 junction connector
(for Sub bus 2)
T17-12 (CANL) B
T17-2 (CANH) V Rear television camera assembly
(for Sub bus 2)
T17-13 (CANL) P
T17-3 (CANH) G CAN No. 6 junction connector
(for Sub bus 2)
T17-14 (CANL) B




CAN NO. 8 JUNCTION CONNECTOR (w/ Parking Assist Monitor System)


a.

Check the CAN No. 8 junction connector.

i.

Connection diagram


ii.
C183982C13
1.781,2.073 2.198,2.313 0.417,0.24 0.938,0.833 0.635,0.833 0.635,0.833 0.635,2.167 false 1.229,1.177 0.927,1.177 0.927,1.177 0.927,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.677,0.99 0.677,0.24 10 false CANH*b 1.292,1.104 1.979,1.396 0.688,0.292 10 false CANL*b 1.875,2.115 2.146,2.281 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 8 Junction Connector)
*b to CAN No. 7 Junction Connector
(for Sub Bus 2)


Check the connection diagram of the components which are connected to the CAN No. 8 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
T18-3 (CANH) L CAN No. 7 junction connector
(for Sub bus 2)
T18-2 (CANL) B




CAN NO. 9 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the CAN No. 9 junction connector.

i.

Connection diagram

C234761C40
2.313,1.198 2.76,1.438 0.448,0.24 3.219,1.406 3.219,0.677 3.219,0.677 2.844,0.677 true 3.365,1.406 3.365,0.26 3.365,0.26 3.74,0.26 true 3.365,1.708 3.365,2.542 3.365,2.542 3.74,2.542 true 3.219,1.708 3.219,2.427 3.219,2.427 2.854,2.427 true 3.5,1.396 3.5,0.583 3.5,0.583 4.417,0.583 true 3.5,1.719 3.5,2.281 3.5,2.281 4.49,2.281 true 0.104,0.073 0.479,0.354 0.375,0.281 10 false *a 2.25,0.615 3.094,0.927 0.844,0.313 10 false CANH*b 2.302,2.354 3.146,2.667 0.844,0.313 10 false CANL*b 3.823,0.177 4.667,0.49 0.844,0.313 10 false CANH*c 3.802,2.458 4.646,2.771 0.844,0.313 10 false CANL*c 2.406,1.25 2.885,1.583 0.479,0.333 10 false S14 4.5,0.49 5.344,0.802 0.844,0.313 10 false CANH*d 4.552,2.198 5.396,2.51 0.844,0.313 10 false CANL*d
*a Front view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to Lane Departure Warning Camera
(for Sub Bus 2)
*c to CAN No. 10 Junction Connector
(for Sub Bus 2)
*d to Network Gateway ECU
(for Sub Bus 2)



ii.

Check the connection diagram of the components which are connected to the CAN No. 9 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
S14-1 (CANH) V Lane departure warning camera
(for Sub bus 2)
S14-7 (CANL) LG
S14-2 (CANH) R CAN No. 10 junction connector
(for Sub bus 2)
S14-8 (CANL) LG
S14-3 (CANH) B Network gateway ECU
(for Sub bus 2)
S14-9 (CANL) LG




CAN NO. 10 JUNCTION CONNECTOR (for LHD with Parking Assist Monitor System)


a.

Check the CAN No. 10 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C258642C18
6.198,1.74 6.469,2.542 true 1.135,4.688 1.573,4.531 true 1.583,5.021 1.146,4.865 true 0.135,0.146 0.573,0.469 0.438,0.323 10 false *1 1.354,0.667 1.792,0.99 0.438,0.323 10 false *a 4.417,0.667 4.854,0.99 0.438,0.323 10 false *b 6.438,2.563 6.875,2.885 0.438,0.323 10 false *c 0.563,4.042 1,4.365 0.438,0.323 10 false *d 1.625,4.427 2.156,4.656 0.531,0.229 10 false CANH 1.635,4.958 2.167,5.188 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I182 4.615,5.198 5.073,5.406 0.458,0.208 10 false I183
*1 CAN No. 10 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 10 Junction Connector)




b.

Check the connection diagram of the components which are connected to the CAN No. 10 junction connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I182-1 (CANH) B Network gateway ECU
(for Sub bus 2)
I182-2 (CANL) LG
I183-1 (CANH) V CAN No. 6 junction connector
(for Sub bus 2)
I183-2 (CANL) LG



CAN NO. 10 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 10 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C258642C19
6.198,1.74 6.469,2.542 true 1.135,4.688 1.573,4.531 true 1.583,5.021 1.146,4.865 true 0.135,0.146 0.573,0.469 0.438,0.323 10 false *1 1.354,0.667 1.792,0.99 0.438,0.323 10 false *a 4.417,0.667 4.854,0.99 0.438,0.323 10 false *b 6.438,2.563 6.875,2.885 0.438,0.323 10 false *c 0.563,4.042 1,4.365 0.438,0.323 10 false *d 1.625,4.427 2.156,4.656 0.531,0.229 10 false CANH 1.635,4.958 2.167,5.188 0.531,0.229 10 false CANL 4.615,5.198 5.073,5.406 0.458,0.208 10 false I182 4.615,4.49 5.073,4.698 0.458,0.208 10 false I184 4.615,4.844 5.073,5.052 0.458,0.208 10 false I183
*1 CAN No. 10 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 10 Junction Connector)




b.

Check the connection diagram of the components which are connected to the CAN No. 10 junction connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I184-1 (CANH) R CAN No. 9 junction connector*1
(for Sub bus 2)
I184-2 (CANL) LG
I183-1 (CANH) V CAN No. 6 junction connector
(for Sub bus 2)
I183-2 (CANL) LG
I182-1 (CANH) B Network gateway ECU*2
(for Sub bus 2)
I182-2 (CANL) LG

*1: w/ Blind Spot Monitor System

*2: w/o Blind Spot Monitor System




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C188081C02
1.5,1.552 1.875,1.771 0.375,0.219 4.198,1.969 4.479,2.354 false 4.26,0.875 3.833,1.406 false 3.052,0.875 3.479,1.406 false 3.844,1.969 3.552,2.354 false 0.188,0.167 0.708,0.333 0.521,0.167 10 false *1 1.594,1.573 1.917,1.781 0.323,0.208 10 false I39 3.365,2.365 3.813,2.531 0.448,0.167 10 false CANL 4.313,0.771 4.76,0.938 0.448,0.167 10 false CANH 4.385,2.375 4.74,2.542 0.354,0.167 10 false BAT 2.802,0.75 3.156,0.917 0.354,0.167 10 false CG
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) L - W*1
G - W*2
HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I39-6 (CANH) - I39-4 (CG) L - W-B*1
G - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-6 (CANH) - I39-16 (BAT) L - R*1
G - R*2
HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


*1: for LHD

*2: for RHD




ECM


A247842C01
2.25,0.344 2.646,0.583 0.396,0.24 5.792,0.344 6.188,0.583 0.396,0.24 2.323,0.354 2.625,0.51 0.302,0.156 10 E26 5.865,0.354 6.167,0.51 0.302,0.156 10 A25 0.198,0.115 0.365,0.292 0.167,0.177 10 *a
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C239445C06
1.833,0.469 2.229,0.708 0.396,0.24 4.417,0.49 4.813,0.729 0.396,0.24 5.208,0.875 5.021,0.875 5.021,0.875 5.031,1.344 false 2.813,0.625 2.51,0.625 2.51,0.625 2.51,1.25 false 2.813,2.167 2.51,2.167 2.51,2.167 2.51,1.313 false 1.25,0.625 1.542,0.625 1.542,0.625 1.542,1.25 false 0.146,0.125 0.313,0.281 0.167,0.156 10 *a 5.271,0.781 5.458,0.938 0.188,0.156 10 E1 2.854,0.521 3.271,0.677 0.417,0.156 10 CANH 2.854,2.052 3.271,2.208 0.417,0.156 10 CANL 0.844,0.51 1.302,0.667 0.458,0.156 10 BATT 1.906,0.479 2.188,0.656 0.281,0.177 10 A25 4.49,0.5 4.771,0.677 0.281,0.177 10 E26
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A25-13 (CANH) - A25-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A25-13 (CANH) - E26-49 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A25-26 (CANL) - E26-49 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A25-13 (CANH) - A25-1 (BATT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A25-26 (CANL) - A25-1 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


E224288C02
1.76,0.219 2.135,0.448 0.375,0.229 5.021,0.219 5.396,0.448 0.375,0.229 1.865,0.24 2.135,0.396 0.271,0.156 10 I18 5.125,0.24 5.396,0.396 0.271,0.156 10 I17 0.125,0.042 0.385,0.219 0.26,0.177 10 *a
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.
E224284C93
1.406,0.24 1.896,0.531 0.49,0.292 1.479,2.156 1.479,2.99 1.479,2.99 1.667,2.99 true 1.365,2.156 1.365,2.625 1.365,2.625 1.177,2.625 true 0.979,1.906 0.979,0.854 0.979,0.854 0.698,0.854 false 1.854,2.156 1.854,2.583 1.854,2.583 2.042,2.583 true 0.104,0.104 0.385,0.385 0.281,0.281 10 false *a 1.729,2.906 2.26,3.146 0.531,0.24 10 false CANH 0.781,2.552 1.313,2.792 0.531,0.24 10 false CANL 0.542,0.76 0.844,1.021 0.302,0.26 10 false B 2.104,2.51 2.417,2.781 0.313,0.271 10 false ES 1.552,0.292 1.833,0.469 0.281,0.177 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I18-17 (CANH) - I18-16 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I18-17 (CANH) - I18-20 (ES) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I18-16 (CANL) - I18-20 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I18-17 (CANH) - I18-1 (B) R - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I18-16 (CANL) - I18-1 (B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B278841C82
2.188,3.771 2.51,3.979 0.323,0.208 5.813,5.01 6.135,5.219 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 4.042,1.135 4.042,0.771 4.042,0.771 4.156,0.771 true 1.677,1.583 1.938,1.583 false 1.677,1.99 1.938,1.99 false 1.021,2.771 0.573,2.771 false 1.688,0.958 1.813,0.729 1.813,0.729 1.969,0.729 false 1.563,1.583 1.479,1.583 1.479,1.583 1.479,3.125 false 1.563,1.99 1.479,1.99 false 4.198,0.698 4.573,0.958 0.375,0.26 10 false MB 3.427,7.563 3.844,7.792 0.417,0.229 10 false MB 5.885,5.042 6.198,5.313 0.313,0.271 10 false 3E 0.906,1.49 1.25,1.719 0.344,0.229 10 false 3C 1.156,5.042 1.521,5.292 0.365,0.25 10 false 3C 5.865,1.458 6.177,1.698 0.313,0.24 10 false 3B 1.823,6.323 2.146,6.542 0.323,0.219 10 false 3B 5.865,2.104 6.208,2.438 0.344,0.333 10 false 3A 4.969,6.323 5.271,6.552 0.302,0.229 10 false 3A 0.917,2.104 1.25,2.406 0.333,0.302 10 false 3D 3.938,5.042 4.292,5.302 0.354,0.26 10 false 3D 1.99,1.49 2.406,1.74 0.417,0.25 10 false I13 4.729,3.802 5.156,4.083 0.427,0.281 10 false I13 1.99,1.906 2.365,2.146 0.375,0.24 10 false I12 2.26,3.802 2.635,4.052 0.375,0.25 10 false I12 0.385,2.708 0.646,2.927 0.26,0.219 10 false 3E 0.229,0.146 0.396,0.323 0.167,0.177 10 false *a 2,0.604 2.302,0.875 0.302,0.271 10 false *1 1.427,3.135 1.729,3.406 0.302,0.271 10 false *2
*1 Main Body ECU
(Multiplex Network Body ECU)
*2 2 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


B282096C91
2.229,3.771 2.552,3.979 0.323,0.208 5.552,5.01 5.875,5.219 0.323,0.208 3.906,5.031 4.229,5.24 0.323,0.208 1.125,5.01 1.448,5.219 0.323,0.208 1.781,6.292 2.104,6.5 0.323,0.208 4.927,6.292 5.25,6.5 0.323,0.208 3.417,7.531 3.74,7.74 0.323,0.208 4.688,3.771 5.01,3.979 0.323,0.208 6.073,5.01 6.396,5.219 0.323,0.208 4.083,1.135 4.083,0.76 4.083,0.76 4.198,0.76 true 1.823,2.063 2.073,2.063 false 1.823,1.719 2.073,1.719 false 0.719,2.76 1.031,2.76 false 1.875,0.979 2.104,0.708 2.104,0.708 2.313,0.708 false 1.594,3.094 1.594,1.49 1.594,1.49 1.698,1.49 false 1.604,1.854 1.708,1.854 false 1.594,2.188 1.698,2.188 false 3.469,7.563 3.823,7.792 0.354,0.229 10 false MB 5.625,5.042 5.875,5.292 0.25,0.25 10 false 3E 1.198,5.042 1.531,5.313 0.333,0.271 10 false 3C 1.844,6.323 2.146,6.583 0.302,0.26 10 false 3B 5.01,6.323 5.354,6.615 0.344,0.292 10 false 3A 3.979,5.063 4.323,5.323 0.344,0.26 10 false 3D 4.76,3.792 5.177,4.052 0.417,0.26 10 false I13 2.302,3.802 2.604,3.99 0.302,0.188 10 false I12 5.854,2.125 6.125,2.375 0.271,0.25 10 false 3A 2.104,1.99 2.385,2.208 0.281,0.219 10 false I12 2.104,1.656 2.438,1.896 0.333,0.24 10 false I13 0.906,2.094 1.208,2.354 0.302,0.26 10 false 3D 0.271,2.604 0.51,2.792 0.24,0.188 10 false 3E 0.5,2.604 0.823,2.875 0.323,0.271 10 false *A 0.271,2.74 0.552,2.979 0.281,0.24 10 false 3F 0.5,2.74 0.802,2.948 0.302,0.208 10 false *B 0.906,1.469 1.229,1.75 0.323,0.281 10 false 3C 5.854,1.458 6.115,1.719 0.26,0.26 10 false 3B 5.896,5.042 6.156,5.271 0.26,0.229 10 false *A 6.146,5.031 6.438,5.292 0.292,0.26 10 false 3F 6.427,5.042 6.75,5.25 0.323,0.208 10 false *B 4.26,0.667 4.656,0.969 0.396,0.302 10 false MB 0.146,0.135 0.396,0.344 0.25,0.208 10 false *a 2.354,0.646 2.604,0.854 0.25,0.208 10 false *1 1.531,3.125 1.781,3.333 0.25,0.208 10 false *2
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

C204058C06
1.792,0.542 2.125,0.76 0.333,0.219 2.146,3.594 2.479,3.813 0.333,0.219 4.771,0.573 5.104,0.792 0.333,0.219 2.708,0.75 2.594,0.75 2.594,0.75 2.052,1.677 false 2.771,1.021 2.635,1.021 2.635,1.021 2.146,1.677 false 5.656,0.708 5.531,0.708 5.531,0.708 5.052,1.656 false 5.854,0.99 5.688,0.99 5.688,0.99 5.125,1.656 false 4.771,4.167 4.625,4.167 4.625,4.167 4.292,3.99 false 3.979,2.844 3.729,2.844 3.729,2.844 3.573,3.417 false 0.969,0.417 1.24,0.729 0.271,0.313 10 false *a 1.979,2.802 2.448,3.094 0.469,0.292 10 false *1 4.854,4.073 5.146,4.25 0.292,0.177 10 false BAT 1.875,0.563 2.25,0.865 0.375,0.302 10 false I12 2.229,3.604 2.552,3.823 0.323,0.219 10 false I39 4.854,0.594 5.198,0.865 0.344,0.271 10 false I13 2.75,0.688 3.333,0.99 0.583,0.302 10 false CANP 2.823,0.948 3.396,1.24 0.573,0.292 10 false CANN 5.698,0.625 6.281,0.885 0.583,0.26 10 false CANL 5.906,0.906 6.479,1.26 0.573,0.354 10 false CANH 4.031,2.792 4.438,2.969 0.406,0.177 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I13-14 (CANH) - I13-13 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I13-14 (CANH) - I39-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I13-13 (CANL) - I39-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I13-14 (CANH) - I39-16 (BAT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I13-13 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) R - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I12-9 (CANP) - I39-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I12-10 (CANN) - I39-4 (CG) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I12-9 (CANP) - I39-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I12-10 (CANN) - I39-16 (BAT) GR - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY


C238830C25
1.583,0.771 2.01,1.052 0.427,0.281 0.208,0.167 0.406,0.333 0.198,0.167 10 false *a 1.667,0.844 2.125,1.042 0.458,0.198 10 false A49
*a Component without harness connected
(Brake Actuator Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly connector.


c.
C238832C70
1.49,0.073 1.969,0.396 0.479,0.323 2.75,1.469 2.75,0.74 2.75,0.74 2.844,0.74 false 0.688,1.479 0.688,0.469 0.688,0.469 0.833,0.469 false 0.927,1.5 0.927,0.781 0.927,0.781 1.146,0.781 false 1.01,1.802 1.01,2.51 1.01,2.51 1.188,2.51 false 0.156,0.146 0.438,0.417 0.281,0.271 10 false *a 1.594,0.156 2.083,0.438 0.49,0.281 10 false A49 2.885,0.656 3.323,0.865 0.438,0.208 10 false GND1 1.188,0.698 1.698,0.906 0.51,0.208 10 false CANH 1.25,2.427 1.76,2.635 0.51,0.208 10 false CANL 0.865,0.385 1.313,0.625 0.448,0.24 10 false +BS
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A49-26 (CANH) - A49-14 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A49-26 (CANH) - A49-38 (GND1) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A49-14 (CANL) - A49-38 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A49-26 (CANH) - A49-25 (+BS) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A49-14 (CANL) - A49-25 (+BS) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the steering sensor connector.


c.
C156493C38
1.188,0.792 1.677,1.083 0.49,0.292 1.219,3.219 1.531,3.219 1.531,3.219 1.531,2.698 false 0.844,2.99 1.333,2.99 1.333,2.99 1.333,2.708 false 2.021,3.229 1.708,3.229 1.708,3.229 1.708,2.708 false 2.583,2.99 2.094,2.99 2.094,2.99 2.094,2.708 false 0.198,0.146 0.396,0.344 0.198,0.198 10 false *a 0.531,2.927 0.979,3.156 0.448,0.229 10 false ESS 0.865,3.156 1.406,3.396 0.542,0.24 10 false CANL 2.073,3.146 2.573,3.354 0.5,0.208 10 false CANH 2.635,2.896 3.083,3.167 0.448,0.271 10 false BAT 1.344,0.865 1.729,1.135 0.385,0.271 10 false I29
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I29-3 (CANH) - I29-2 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I29-3 (CANH) - I29-1 (ESS) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I29-2 (CANL) - I29-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I29-3 (CANH) - I29-5 (BAT) V - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I29-2 (CANL) - I29-5 (BAT) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


C239855C12
3.729,0.198 4.052,0.396 0.323,0.198 5.719,0.198 6.042,0.396 0.323,0.198 3.906,1.844 4.229,2.042 0.323,0.198 4.708,1.844 5.031,2.042 0.323,0.198 5.563,1.844 5.885,2.042 0.323,0.198 1.875,0.833 2.198,1.031 0.323,0.198 0.719,1.313 1.042,1.51 0.323,0.198 1.104,1.313 1.427,1.51 0.323,0.198 1.479,1.313 1.802,1.51 0.323,0.198 0.688,3.469 1.01,3.667 0.323,0.198 0.906,1.313 1.031,1.146 false 1.271,1.313 1.292,1.146 false 1.625,1.313 1.542,1.146 false 2.021,0.833 2.021,0.771 false 1.01,3.521 1.083,3.49 false 3.854,0.229 4.115,0.375 0.26,0.146 10 false j2 5.844,0.219 6.094,0.365 0.25,0.146 10 false c 4.021,1.865 4.26,2.104 0.24,0.24 10 false j1 4.833,1.865 5.01,2.01 0.177,0.146 10 false a 5.688,1.865 5.865,2.01 0.177,0.146 10 false b 0.125,0.115 0.406,0.344 0.281,0.229 10 false *a 1.99,0.854 2.26,1.115 0.271,0.26 10 false j2 0.823,1.344 1.073,1.583 0.25,0.24 10 false j1 1.219,1.333 1.396,1.479 0.177,0.146 10 false a 1.594,1.344 1.771,1.49 0.177,0.146 10 false b 0.823,3.49 1.073,3.635 0.25,0.146 10 false c
*a Component without harness connected
(Power Steering ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C240514C04
1.25,1.521 1.646,1.76 0.396,0.24 4.875,0.792 5.271,1.031 0.396,0.24 4.563,1.74 4.219,1.74 false 5.875,1.74 5.542,1.74 false 2.302,1.844 2.552,1.406 2.552,1.406 2.688,1.406 false 2.667,2.073 2.333,2.073 false 0.115,0.104 0.479,0.396 0.365,0.292 10 false *a 2.719,1.333 3.198,1.552 0.479,0.219 10 false CANH 2.708,2 3.167,2.198 0.458,0.198 10 false CANL 3.969,1.667 4.302,1.865 0.333,0.198 10 false PIG 5.948,1.667 6.406,1.865 0.458,0.198 10 false PGND 1.396,1.563 1.688,1.875 0.292,0.313 10 false j1 5.021,0.833 5.333,1.083 0.313,0.25 10 false j2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j1-4 (CANH) - j1-8 (CANL) Y - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
j1-4 (CANH) - j2-2 (PGND) Y - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
j1-8 (CANL) - j2-2 (PGND) SB - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
j1-4 (CANH) - j2-1 (PIG) Y - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
j1-8 (CANL) - j2-1 (PIG) SB - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C188802C12
0.552,1.552 0.927,1.76 0.375,0.208 3.323,1.594 3.698,1.802 0.375,0.208 1.208,1.135 1.5,1.615 false 1.417,1.885 1.198,2.354 false 1.688,1.885 1.604,2.24 false 5.698,1.969 5.906,2.375 false 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 1.01,2.385 1.479,2.604 0.469,0.219 10 false CANL 1.01,0.958 1.594,1.208 0.583,0.25 10 false CANH 1.521,2.271 1.854,2.531 0.333,0.26 10 false E1 5.802,2.417 6.156,2.583 0.354,0.167 10 false BAT 0.656,1.583 1.104,1.875 0.448,0.292 10 false I47 3.396,0.177 3.896,0.344 0.5,0.167 10 false *1 3.427,1.615 3.854,1.885 0.427,0.271 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I47-13 (CANH) - I47-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I47-13 (CANH) - I47-25 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I47-22 (CANL) - I47-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I47-13 (CANH) - I39-16 (BAT) Y - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I47-22 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)


B264892C08
1.875,0.667 2.271,0.906 0.396,0.24 3.26,0.667 3.656,0.906 0.396,0.24 4.792,0.667 5.188,0.906 0.396,0.24 1.948,0.719 2.24,0.875 0.292,0.156 10 false A43 3.365,0.719 3.656,0.875 0.292,0.156 10 false O1 4.896,0.719 5.188,0.875 0.292,0.156 10 false I78 0.104,0.104 0.5,0.365 0.396,0.26 10 false *a
*a Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the smart key ECU assembly (certification ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

C240482C05
1.01,1.323 1.406,1.563 0.396,0.24 3.896,1.302 4.292,1.542 0.396,0.24 4.542,0.656 4.906,0.656 4.906,0.656 4.906,1.417 false 5.354,0.656 4.99,0.656 4.99,0.656 4.99,1.417 false 1.302,0.667 1.677,0.667 1.677,0.667 1.677,1.292 false 2.51,1.583 2.76,1.583 false 0.135,0.125 0.49,0.438 0.354,0.313 10 false *a 1.104,0.594 1.521,0.813 0.417,0.219 10 false +B 2.802,1.49 2.969,1.667 0.167,0.177 10 false E 4.167,0.594 4.667,0.813 0.5,0.219 10 false CANL 5.396,0.583 5.979,0.844 0.583,0.26 10 false CANH 1.083,1.354 1.406,1.531 0.323,0.177 10 false A43 4,1.344 4.302,1.521 0.302,0.177 10 false I78
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I78-14 (CANH) - I78-15 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I78-14 (CANH) - A43-11 (E) L - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I78-15 (CANL) - A43-11 (E) W - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I78-14 (CANH) - A43-2 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I78-15 (CANL) - A43-2 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


E277812C41
2.167,0.188 2.563,0.375 0.396,0.188 2.229,1.594 2.625,1.781 0.396,0.188 1.438,1.594 1.833,1.781 0.396,0.188 3.792,1.573 4.188,1.76 0.396,0.188 5.271,1.427 5.667,1.615 0.396,0.188 4.469,0.188 4.865,0.375 0.396,0.188 2.219,0.198 2.573,0.396 0.354,0.198 10 false I179 4.531,0.198 4.979,0.427 0.448,0.229 10 false I155 1.5,1.604 1.906,1.802 0.406,0.198 10 false I152 2.292,1.604 2.802,1.865 0.51,0.26 10 false I153 3.865,1.594 4.219,1.792 0.354,0.198 10 false I156 5.375,1.427 5.729,1.625 0.354,0.198 10 false RA
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C240506C17
0.604,1.448 1,1.688 0.396,0.24 3.875,1.448 4.271,1.688 0.396,0.24 1.844,0.552 2,0.552 2,0.552 2,1.688 false 2.333,0.552 2.115,0.552 2.115,0.552 2.115,1.688 false 5.781,0.531 5.625,0.531 5.625,0.531 5.625,1.51 false 5.177,2.292 5.01,2.292 5.01,2.292 5.01,1.896 false 0.135,0.052 0.313,0.229 0.177,0.177 10 false *a 2.417,0.49 3.073,0.802 0.656,0.313 10 false CANL 1.427,0.479 2.073,0.813 0.646,0.333 10 false CANH 5.865,0.448 6.25,0.74 0.385,0.292 10 false +B1 5.229,2.219 5.823,2.51 0.594,0.292 10 false GND1 0.656,1.49 1.021,1.75 0.365,0.26 10 false I155 3.948,1.49 4.406,1.792 0.458,0.302 10 false I152
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I155-9 (CANH) - I155-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I155-9 (CANH) - I152-7 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I155-10 (CANL) - I152-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I155-9 (CANH) - I152-4 (+B1) R - L-Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I155-10 (CANL) - I152-4 (+B1) W - L-Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


E277812C35
2.146,0.198 2.542,0.385 0.396,0.188 2.229,1.594 2.625,1.781 0.396,0.188 1.438,1.594 1.833,1.781 0.396,0.188 3.792,1.552 4.188,1.74 0.396,0.188 5.271,1.427 5.667,1.615 0.396,0.188 4.469,0.188 4.865,0.375 0.396,0.188 2.219,0.208 2.573,0.406 0.354,0.198 10 false I178 4.573,0.198 4.927,0.396 0.354,0.198 10 false I67 1.542,1.594 1.896,1.792 0.354,0.198 10 false I64 2.344,1.594 2.698,1.792 0.354,0.198 10 false I65 3.854,1.563 4.208,1.76 0.354,0.198 10 false I147 5.365,1.438 5.719,1.635 0.354,0.198 10 false RA 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the navigation receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C240506C18
0.594,1.49 0.99,1.729 0.396,0.24 3.875,1.479 4.271,1.719 0.396,0.24 1.854,0.542 2.01,0.542 2.01,0.542 2.01,1.677 false 2.333,0.542 2.115,0.542 2.115,0.542 2.115,1.677 false 5.771,0.521 5.615,0.521 5.615,0.521 5.615,1.5 false 5.177,2.313 5.01,2.313 5.01,2.313 5.01,1.917 false 0.125,0.125 0.479,0.438 0.354,0.313 10 false *a 2.375,0.479 2.813,0.656 0.438,0.177 10 false CANL 1.458,0.479 1.896,0.656 0.438,0.177 10 false CANH 5.833,0.448 6.135,0.625 0.302,0.177 10 false +B1 5.229,2.25 5.677,2.438 0.448,0.188 10 false GND1 0.708,1.542 1.021,1.75 0.313,0.208 10 false I67 3.979,1.521 4.26,1.698 0.281,0.177 10 false I64
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I67-9 (CANH) - I67-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I67-9 (CANH) - I64-7 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I67-10 (CANL) - I64-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I67-9 (CANH) - I64-4 (+B1) R - L-Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I67-10 (CANL) - I64-4 (+B1) W - L-Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


E226604C16
2.958,0.104 3.292,0.333 0.333,0.229 5.083,0.104 5.417,0.333 0.333,0.229 5.188,0.146 5.365,0.333 0.177,0.188 10 false z1 3.031,0.146 3.344,0.302 0.313,0.156 10 false I77 0.146,0.135 0.458,0.438 0.313,0.302 10 false *a
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C188799C10
1.75,1.75 2.146,1.948 0.396,0.198 3.625,1.938 3.042,1.052 false 3.729,1.938 4.313,1.052 false 2.677,2.146 2.396,2.51 false 4.271,2.5 3.917,2.01 false 0.219,0.177 0.656,0.521 0.438,0.344 10 false *a 4.167,0.875 4.615,1.042 0.448,0.167 10 false CANL 2.833,0.896 3.281,1.063 0.448,0.167 10 false CANH 2.323,2.51 2.5,2.677 0.177,0.167 10 false B 4.156,2.521 4.583,2.688 0.427,0.167 10 false GND 1.854,1.771 2.177,1.948 0.323,0.177 10 false I77
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I77-11 (CANH) - I77-12 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I77-11 (CANH) - I77-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I77-12 (CANL) - I77-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I77-11 (CANH) - I77-21 (B) V - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I77-12 (CANL) - I77-21 (B) W - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Seat Position Memory System)


B209687C16
2.975,0.247 3.253,0.448 0.278,0.200 10 z6 2.891,0.218 3.217,0.425 0.326,0.207 4.096,0.255 4.346,0.477 0.251,0.222 10 J13 4.044,0.225 4.37,0.432 0.326,0.207 0.119,0.014 0.735,0.440 0.616,0.427 10 *a
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer mirror control ECU assembly RH connector.


c.
C204179C35
1.51,0.25 1.896,0.458 0.385,0.208 0.948,1.823 1.24,1.438 false 1.385,1.438 1.542,1.865 false 2.177,1.135 2.552,1.135 false 2.531,0.615 2.271,0.615 2.271,0.615 1.948,1.135 false 0.083,0.094 0.51,0.385 0.427,0.292 10 false *a 1.396,1.896 1.802,2.073 0.406,0.177 10 false CANP 0.76,1.844 1.25,2.083 0.49,0.24 10 false CANN 2.604,1.063 3.01,1.302 0.406,0.24 10 false GND 2.583,0.552 3.063,0.823 0.479,0.271 10 false CPUB 1.583,0.281 1.938,0.552 0.354,0.271 10 false J13
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J13-9 (CANP) - J13-8 (CANN) P - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J13-9 (CANP) - J13-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J13-8 (CANN) - J13-7 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J13-9 (CANP) - J13-6 (CPUB) P - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J13-8 (CANN) - J13-6 (CPUB) GR - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)


B209687C17
2.933,0.247 3.229,0.453 0.296,0.206 10 z5 2.849,0.218 3.175,0.425 0.326,0.207 4.047,0.255 4.327,0.477 0.280,0.222 10 K12 4.002,0.225 4.327,0.432 0.326,0.207 0.109,0 0.464,0.282 0.356,0.282 10 *a
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer mirror control ECU assembly LH connector.


c.
C204179C36
1.5,0.25 1.906,0.469 0.406,0.219 0.948,1.823 1.24,1.438 false 1.375,1.438 1.531,1.865 false 2.188,1.156 2.563,1.156 false 2.521,0.604 2.271,0.604 2.271,0.604 1.948,1.125 false 0.104,0.083 0.531,0.375 0.427,0.292 10 false *a 1.375,1.875 1.854,2.115 0.479,0.24 10 false CANP 0.75,1.833 1.229,2.073 0.479,0.24 10 false CANN 2.615,1.073 3.021,1.344 0.406,0.271 10 false GND 2.573,0.531 3.031,0.792 0.458,0.26 10 false CPUB 1.583,0.281 1.99,0.531 0.406,0.25 10 false K12
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K12-9 (CANP) - K12-8 (CANN) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
K12-9 (CANP) - K12-7 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
K12-8 (CANN) - K12-7 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
K12-9 (CANP) - K12-6 (CPUB) G - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K12-8 (CANN) - K12-6 (CPUB) GR - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for LHD) (for Driver Side) (w/ Seat Position Memory System)


B219506C05
3.161,0.297 3.429,0.443 0.268,0.146 10 e11 4.136,0.297 4.399,0.455 0.263,0.158 10 e12 4.092,0.264 4.405,0.472 0.313,0.209 3.113,0.264 3.426,0.472 0.313,0.209 0.125,0.063 0.331,0.255 0.205,0.192 10 *a
*a Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the position control ECU and switch assembly (for driver side) connectors.


c.

Measure the resistance according to the value(s) in the table below.

C204065C29
1.958,0.573 2.302,0.781 0.344,0.208 4.854,0.438 5.219,0.656 0.365,0.219 5.031,2.448 4.802,2.094 false 4.333,2.427 4.656,2.094 false 1.396,2.365 1.792,2.031 false 1.417,1.333 1.802,1.771 false 0.063,0.063 0.708,0.354 0.646,0.292 10 false *a 2.021,0.594 2.313,0.823 0.292,0.229 10 false e11 4.927,0.469 5.25,0.646 0.323,0.177 10 false e12 5,2.458 5.49,2.635 0.49,0.177 10 false CANP 3.958,2.458 4.458,2.635 0.5,0.177 10 false CANN 1.073,1.26 1.396,1.438 0.323,0.177 10 false GND 1.198,2.365 1.542,2.594 0.344,0.229 10 false +B
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
e12-8 (CANP) - e12-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
e12-8 (CANP) - e11-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e12-7 (CANN) - e11-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e12-8 (CANP) - e11-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
e12-7 (CANN) - e11-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for RHD) (for Driver Side) (w/ Seat Position Memory System)


B219505C04
2.802,0.083 3.135,0.281 0.333,0.198 3.688,0.083 4.021,0.281 0.333,0.198 3.75,0.115 4.313,0.365 0.563,0.25 10 false d11 2.854,0.115 3.438,0.375 0.583,0.26 10 false d12 0.104,0.115 0.823,0.708 0.719,0.594 10 false *a
*a Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the position control ECU and switch assembly (for driver side) connectors.


c.

Measure the resistance according to the value(s) in the table below.

C204065C08
1.958,0.573 2.302,0.781 0.344,0.208 4.854,0.438 5.219,0.656 0.365,0.219 5.01,2.5 4.781,2.146 false 4.323,2.469 4.646,2.135 false 1.427,2.417 1.823,2.083 false 1.427,1.354 1.813,1.792 false 0.104,0.115 0.75,0.406 0.646,0.292 10 false *a 2.031,0.594 2.323,0.823 0.292,0.229 10 false d11 4.927,0.479 5.25,0.656 0.323,0.177 10 false d12 4.854,2.531 5.344,2.708 0.49,0.177 10 false CANP 4.125,2.479 4.625,2.656 0.5,0.177 10 false CANN 1.094,1.26 1.552,1.552 0.458,0.292 10 false GND 1.229,2.417 1.552,2.604 0.323,0.188 10 false +B
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d12-8 (CANP) - d12-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
d12-8 (CANP) - d11-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d12-7 (CANN) - d11-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d12-8 (CANP) - d11-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d12-7 (CANN) - d11-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NETWORK GATEWAY ECU (w/ Parking Assist Monitor System)


C238891C03
3.375,0.375 3.771,0.615 0.396,0.24 3.448,0.417 3.906,0.719 0.458,0.302 10 false I160 0.135,0.135 0.438,0.385 0.302,0.25 10 false *a
*a Component without harness connected
(Network Gateway ECU)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the network gateway ECU connector.


c.
C238892C37
0.458,1.198 0.948,1.49 0.49,0.292 1.833,1.406 1.833,0.365 1.833,0.365 1.313,0.365 false 1.958,1.51 1.958,1.833 1.958,1.833 1.313,1.833 false 2.198,1.51 2.198,1.833 2.198,1.833 2.719,1.833 false 2.375,1.438 2.74,1.438 false 1.229,1.271 1.229,0.667 1.229,0.667 0.906,0.667 false 2.188,1.271 2.188,0.656 2.188,0.656 2.469,0.656 false 0.948,0.302 1.417,0.552 0.469,0.25 10 false CA2L 0.906,1.771 1.385,1.99 0.479,0.219 10 false CA2H 2.781,1.76 3.219,1.969 0.438,0.208 10 false CA1L 2.802,1.375 3.188,1.531 0.385,0.156 10 false CA1H 0.563,1.271 0.958,1.521 0.396,0.25 10 false I160 0.083,0.083 0.406,0.313 0.323,0.229 10 false *a 0.51,0.594 0.979,0.802 0.469,0.208 10 false BATT 2.531,0.594 2.979,0.865 0.448,0.271 10 false GND
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I160-16 (CA1H) - I160-15 (CA1L) G - W*1
BE - W*2
HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I160-16 (CA1H) - I160-4 (GND) G - W-B*1
BE - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I160-15 (CA1L) - I160-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I160-16 (CA1H) - I160-2 (BATT) G - W*1
BE - W*2
HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I160-15 (CA1L) - I160-2 (BATT) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) B - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I160-13 (CA2H) - I160-4 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I160-12 (CA2L) - I160-4 (GND) LG - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I160-13 (CA2H) - I160-2 (BATT) B - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I160-12 (CA2L) - I160-2 (BATT) LG - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


*1: for LHD

*2: for RHD




BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)


E233761C33
2.26,0.75 2.635,0.979 0.375,0.229 2.313,0.802 2.792,1.188 0.479,0.385 10 false O32 0.083,0.01 0.302,0.198 0.219,0.188 10 false *a
*a Component without harness connected
(Blind Spot Monitor Sensor RH)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

C250047C14
3.51,1.521 3.885,1.75 0.375,0.229 0.906,1.521 1.281,1.75 0.375,0.229 5.719,1.938 5.719,2.385 5.719,2.385 5.865,2.385 false 2.323,1.896 2.323,2.344 2.323,2.344 2.438,2.344 false 1.958,1.896 1.958,2.333 1.958,2.333 1.76,2.333 false 1.958,1.708 1.958,0.927 1.958,0.927 1.688,0.927 false 0.438,0.042 0.635,0.219 0.198,0.177 10 false *a 3.292,0.063 3.49,0.24 0.198,0.177 10 false *1 5.906,2.313 6.26,2.49 0.354,0.177 10 false BAT 3.594,1.573 3.844,1.75 0.25,0.177 10 false I39 0.969,1.552 1.51,1.906 0.542,0.354 10 false O32 2.479,2.271 2.948,2.448 0.469,0.177 10 false BRGD 1.354,2.26 1.823,2.438 0.469,0.177 10 false CA1N 1.292,0.854 1.76,1.031 0.469,0.177 10 false CA1P
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O32-2 (CA1P) - O32-7 (CA1N) R - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
O32-2 (CA1P) - O32-10 (BRGD) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
O32-7 (CA1N) - O32-10 (BRGD) B - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
O32-2 (CA1P) - I39-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O32-7 (CA1N) - I39-16 (BAT) B - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System)


E220917C06
3.5,0.104 3.896,0.344 0.396,0.24 3.604,0.156 3.875,0.385 0.271,0.229 10 false I82 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Clearance Warning ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C240483C09
1.198,0.698 1.573,0.927 0.375,0.229 4.896,0.698 5.271,0.927 0.375,0.229 3.073,0.958 2.813,0.958 2.813,0.958 2.813,1.781 false 2.427,0.958 2.719,0.958 2.719,0.958 2.719,1.792 false 2.156,2.365 1.99,2.365 1.99,2.365 1.99,1.917 false 5.885,2.375 5.708,2.375 5.708,2.375 5.708,1.969 false 0.125,0.104 0.313,0.292 0.188,0.188 10 false *a 3.604,0.104 3.792,0.292 0.188,0.188 10 false *1 5.948,2.292 6.271,2.479 0.323,0.188 10 false BAT 2.177,2.292 2.354,2.479 0.177,0.188 10 false E 3.104,0.896 3.344,1.083 0.24,0.188 10 false R2 2.24,0.896 2.479,1.083 0.24,0.188 10 false R1 1.292,0.74 1.51,0.906 0.219,0.167 10 false I82 5,0.74 5.292,0.906 0.292,0.167 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I82-17 (R1) - I82-18 (R2) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I82-17 (R1) - I82-30 (E) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I82-18 (R2) - I82-30 (E) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I82-17 (R1) - I39-16 (BAT) BE - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I82-18 (R2) - I39-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


C302330C09
3.323,0.198 3.729,0.406 0.406,0.208 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 3.417,0.219 3.927,0.479 0.51,0.26 10 false T25
*a Component without harness connected
(Rear Television Camera Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C295280C15
1.979,0.094 2.375,0.365 0.396,0.271 5.042,0.083 5.438,0.354 0.396,0.271 1.594,1.49 1.719,1.49 1.719,1.49 2.01,1.073 true 1.563,0.344 1.688,0.344 1.688,0.344 2.01,0.844 true 5.146,0.667 4.792,0.271 4.792,0.271 4.656,0.271 true 6.198,1.521 6.083,1.521 6.083,1.521 5.875,1.146 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 2.073,0.135 2.563,0.469 0.49,0.333 10 false T25 1.135,1.406 1.75,1.604 0.615,0.198 10 false CANH 1.125,0.26 1.74,0.458 0.615,0.198 10 false CANL 4.385,0.188 5,0.385 0.615,0.198 10 false CG 5.115,0.125 5.573,0.323 0.458,0.198 10 false I39 6.292,1.438 6.75,1.635 0.458,0.198 10 false BAT 3.781,0.094 4.094,0.292 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T25-4 (CANH) - T25-1 (CANL) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
T25-4 (CANH) - I39-4 (CG) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T25-1 (CANL) - I39-4 (CG) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T25-4 (CANH) - I39-16 (BAT) V - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T25-1 (CANL) - I39-16 (BAT) P - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




LANE DEPARTURE WARNING CAMERA (w/ Blind Spot Monitor System)


C265805C09
3.427,0.24 3.885,0.469 0.458,0.229 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 3.563,0.271 4.052,0.51 0.49,0.24 10 false S15
*a Component without harness connected
(Lane Departure Warning Camera)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the lane departure warning camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C292389C08
1.771,0.083 2.198,0.354 0.427,0.271 5.104,0.063 5.531,0.333 0.427,0.271 5.948,1.167 6.198,1.542 6.198,1.542 6.323,1.542 true 2.281,0.917 2.646,0.49 2.646,0.49 2.76,0.49 true 2.292,1.146 2.573,1.469 2.573,1.469 2.677,1.469 true 2.146,1.146 1.958,1.625 1.958,1.625 1.833,1.625 true 0.677,0.083 0.99,0.281 0.313,0.198 10 false *a 3.51,0.083 3.823,0.281 0.313,0.198 10 false *1 1.875,0.146 2.448,0.448 0.573,0.302 10 false S15 5.229,0.104 5.542,0.302 0.313,0.198 10 false I39 6.396,1.448 6.854,1.646 0.458,0.198 10 false BAT 1.479,1.531 1.938,1.729 0.458,0.198 10 false GND 2.76,1.375 3.375,1.573 0.615,0.198 10 false CA1N 2.833,0.396 3.448,0.594 0.615,0.198 10 false CA1P
*1 DLC3 - -
*a Front view of wire harness connector
(to Lane Departure Warning Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S15-6 (CA1P) - S15-12 (CA1N) V - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S15-6 (CA1P) - S15-11 (GND) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S15-12 (CA1N) - S15-11 (GND) LG - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S15-6 (CA1P) - I39-16 (BAT) V - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S15-12 (CA1N) - I39-16 (BAT) LG - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher