Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in One Side of CAN Branch Line  


DESCRIPTION

If an ECU or sensor is not displayed on the CAN Bus Check screen of the GTS and some ECUs and sensors repeatedly appear and disappear from the screen when the CAN main bus lines are normal (there is no open, short, short to +B or short to GND in the main bus lines), there may be an open circuit in either of one pair of CAN branch lines.

HINT:

If some ECUs and sensors repeatedly appear and disappear from the CAN Bus Check screen, communication between the normal ECUs (sensors) and the GTS may be affected by the incomplete signals that are output from the ECU that has an open circuit in either of its CAN branch lines. In this case, the CAN branch lines for the ECUs and sensors that repeatedly appear and disappear from the screen are normal and the ECU that is not displayed on the screen may be the main cause of the problem (this ECU may have an open circuit in either of its CAN branch lines).


Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the GTS "CAN Bus Check" screen. One side of CAN branch line is open, or output signals are incomplete.
·

ECM

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Brake actuator assembly

·

Steering sensor

·

Network gateway ECU*1

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (certification ECU)

·

Navigation receiver assembly*2

·

Radio and display receiver assembly*3

·

Clearance warning ECU assembly*4



*1: w/ Parking Assist Monitor System

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Toyota Parking Assist-sensor System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure (for LHD): Turn the engine switch on (IG) and drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

DTC check procedure (for RHD): Turn the engine switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 52 seconds, and drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF V BUS BRANCH LINE
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Using the GTS, select and perform the CAN bus check.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


c.

Observe the screen for approximately 2 minutes to check the ECUs and sensors that are not displayed on the screen and also those that repeatedly appear and disappear from the screen.


d.

Check the applicable communication stop mode for the ECU or sensor that is not displayed on the screen.


Result:
Proceed to
NEXT



NEXT

GO TO CORRESPONDING COMMUNICATION STOP MODE