| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| U023A | Lost Communication with Front Camera Module | No communication from the lane departure warning camera continues. | ·
Lane departure warning camera branch line or connector ·
Power source circuit of lane departure warning camera ·
Lane departure warning camera ground circuit ·
Lane departure warning camera |
The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. |
The diagnostic procedure is for when DTC U023A is output by the network gateway ECU (GTS display: Gateway).
Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the engine switch on (IG), wait at least 52 seconds, and then drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 second or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Inspect the fuses for circuits related to this system before performing the following procedure.
Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Reconfirm DTCs.
If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.
| Result | Proceed to |
|---|---|
| DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) | A |
| DTC U1002 is output from the network gateway ECU (GTS display: Gateway) | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Lane Departure Warning Camera) |
Disconnect the lane departure warning camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S15-6 (CA1P) - S15-12 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Lane Departure Warning Camera) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S15-11 (GND) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S15-7 (IGB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG