Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2015.04
RM2030EQ _58 Vehicle Interior _014666 LIGHTING (INT) _0074614 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the engine switch on (IG) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E239243E05
0.406,0.656 1.281,0.875 0.875,0.219 10 false from Battery 0.135,1.146 1.219,1.75 1.083,0.604 10 false from Certification ECU 3.448,2.5 6.146,2.677 2.698,0.177 10 false Instrument Panel Junction Block Assembly 5.479,2.969 7.135,3.333 1.656,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 3.698,0.458 3.865,0.604 0.167,0.146 10 false 1 3.583,0.677 3.917,0.823 0.333,0.146 10 false 3E*4 3.208,0.958 3.427,1.104 0.219,0.146 10 false 27 3.188,1.146 3.385,1.292 0.198,0.146 10 false 3A 4.156,1.438 4.813,1.583 0.656,0.146 10 false IG1 NO. 2 4.781,0.844 5.792,0.99 1.01,0.146 10 false ECU-IG1 NO. 2 6.281,0.688 6.479,0.844 0.198,0.156 10 false IG 3.24,1.729 3.406,1.875 0.167,0.146 10 false 7 3.188,1.927 3.385,2.073 0.198,0.146 10 false 3B 5.896,0.49 6.135,0.635 0.24,0.146 10 false 32 5.875,0.677 6.167,0.844 0.292,0.167 10 false MB 2.01,0.833 2.365,1.063 0.354,0.229 10 false ALT 3.25,0.458 3.417,0.604 0.167,0.146 10 false 1 3.135,0.677 3.531,0.823 0.396,0.146 10 false 3F*3 0.146,3.094 1.042,3.302 0.896,0.208 10 false *1: for RHD 0.146,3.385 1.052,3.594 0.906,0.208 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Engine switch on (IG) signal ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the 3A, 3B, 3F*1 and 3E*2 instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground*1 Engine switch off 11 to 14 V
3E-1 - Body ground*2 Engine switch off 11 to 14 V
3A-27 - Body ground Engine switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-7 - Body ground Always Below 1 Ω


*1: for RHD

*2: for LHD



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E191506C12
1.927,0.281 2.24,0.49 0.313,0.208 5.281,0.365 5.594,0.573 0.313,0.208 0.792,2.198 1.115,2.406 0.323,0.208 4.563,2.354 4.875,2.563 0.313,0.208 1.417,2.198 1.74,2.406 0.323,0.208 6.531,3 6.688,3.49 false 2,0.313 2.26,0.521 0.26,0.208 10 3A 5.365,0.396 5.625,0.604 0.26,0.208 10 3B 1.198,2.229 1.458,2.438 0.26,0.208 10 *A 4.615,2.385 4.875,2.594 0.26,0.208 10 MB 6.635,3.51 6.844,3.708 0.208,0.198 10 IG 0.271,0.052 0.458,0.24 0.188,0.188 10 *a 1.5,2.229 1.76,2.438 0.26,0.208 10 3F 0.885,2.229 1.146,2.438 0.26,0.208 10 3E 1.792,2.219 2.052,2.427 0.26,0.208 10 *B
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - MB-32 (IG)*1 Always 10 kΩ or higher
3E-1 - MB-32 (IG)*1 Battery positive (+) → 3A-27
Battery negative (-) → 3B-7
Below 1 Ω
3F-1 - MB-32 (IG)*2 Always 10 kΩ or higher
3F-1 - MB-32 (IG)*2 Battery positive (+) → 3A-27
Battery negative (-) → 3B-7
Below 1 Ω


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY