Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2015.04
RM2030EQ _58 Vehicle Interior _014666 LIGHTING (INT) _0074614 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Personal Light*

·

Rear Interior Light


HINT:

The light cut relay supplies power to the lights not controlled by the illuminated entry system. If all the lights that use power from the light cut relay do not turn on, check the light cut relay circuit first.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


*: w/ Sliding Roof


WIRING DIAGRAM

E318755E01
0.125,0.146 3.25,0.385 3.125,0.24 12 false w/o Sliding Roof: 0.375,1.458 3.438,1.656 3.063,0.198 10 false from Light Cut Relay 3.5,1.26 3.958,1.458 0.458,0.198 10 false CTY 3.667,1.51 4.125,1.708 0.458,0.198 10 false E 2.313,1.365 2.771,1.563 0.458,0.198 10 false B 2.094,1.354 2.552,1.552 0.458,0.198 11 false 1 3.865,1.25 4.323,1.448 0.458,0.198 11 false 3 3.875,1.479 4.333,1.677 0.458,0.198 11 false 2 4.531,1.344 4.99,1.542 0.458,0.198 11 false 3B 4.542,1.156 5,1.354 0.458,0.198 11 false 35 5.802,1.344 6.26,1.542 0.458,0.198 11 false MB 5.865,1.146 6.323,1.344 0.458,0.198 11 false 1 6.219,1.344 6.677,1.542 0.458,0.198 11 false ILE 2.177,2.125 5.24,2.323 3.063,0.198 10 false No.1 Room Light Assembly 2.177,1.948 5.24,2.146 3.063,0.198 10 false S11 4.365,1.792 5.979,2.281 1.615,0.49 10 false Instrument Panel Junction Block Assembly 5.417,2.646 7.073,3.135 1.656,0.49 10 false Main Body ECU (Multiplex Network Body ECU)

E318756E01
0.083,0.031 3.021,0.271 2.938,0.24 12 false w/ Sliding Roof: 1.927,0.365 4.99,0.563 3.063,0.198 10 false from Light Cut Relay 3.958,1.448 4.417,1.646 0.458,0.198 10 false SIG 4.323,1.448 4.781,1.646 0.458,0.198 10 false 7 0.26,1.563 0.719,1.76 0.458,0.198 10 false 9 0.458,1.563 0.917,1.76 0.458,0.198 10 false B 1.292,1.458 1.74,1.656 0.448,0.198 10 false OFF 1.365,1.896 1.813,2.094 0.448,0.198 10 false ON 2.427,1.979 2.875,2.177 0.448,0.198 10 false OFF 2.51,2.406 2.958,2.604 0.448,0.198 10 false ON 3.49,1.979 3.938,2.177 0.448,0.198 10 false OFF 3.531,2.406 3.979,2.604 0.448,0.198 10 false ON 1.365,3.24 1.813,3.438 0.448,0.198 10 false ON 1.323,2.802 1.771,3 0.448,0.198 10 false OFF 0.719,2.104 1.635,2.542 0.917,0.438 10 false Personal Light Switch RH 0.51,3.469 2.594,3.875 2.083,0.406 10 false Personal Light Switch LH 2,2.625 2.792,3.063 0.792,0.438 10 false Interior Light Door Switch 2.99,2.635 3.802,3.073 0.813,0.438 10 false Interior Light on/off Switch 3.969,3.396 4.427,3.594 0.458,0.198 10 false CTY 4.323,3.396 4.781,3.594 0.458,0.198 10 false 6 3.771,3.833 4.229,4.031 0.458,0.198 10 false 1 3.563,3.625 4.021,3.823 0.458,0.198 10 false GND 0.458,3.865 0.917,4.063 0.458,0.198 10 false S7 0.771,3.875 2.854,4.281 2.083,0.406 10 false Roof Console Box Assembly 5.052,3.49 5.51,3.688 0.458,0.198 10 false 3B 5.063,3.302 5.521,3.5 0.458,0.198 10 false 35 5.917,0.813 6.375,1.01 0.458,0.198 10 false MB 5.979,0.625 6.438,0.823 0.458,0.198 10 false 1 6.313,0.823 6.771,1.021 0.458,0.198 10 false ILE 4.896,3.865 5.979,4.708 1.083,0.844 10 false Instrument Panel Junction Block Assembly 6.01,5.323 7.021,6.167 1.01,0.844 10 false Main Body ECU (Multiplex Network Body ECU) 0.875,4.854 1.333,5.052 0.458,0.198 10 false B 0.656,4.854 1.115,5.052 0.458,0.198 10 false 4 3.177,4.729 3.635,4.927 0.458,0.198 10 false CTY 3.563,4.729 4.021,4.927 0.458,0.198 10 false 2 3.563,4.979 4.021,5.177 0.458,0.198 10 false 1 3.354,4.979 3.813,5.177 0.458,0.198 10 false E 2.448,4.74 2.896,4.938 0.448,0.198 10 false OFF 2.521,5.177 2.969,5.375 0.448,0.198 10 false ON 2.521,6.24 2.969,6.438 0.448,0.198 10 false ON 2.448,5.802 2.896,6 0.448,0.198 10 false OFF 1.188,5.406 3.271,5.813 2.083,0.406 10 false Rear Personal Light Switch LH 1.198,6.49 3.281,6.896 2.083,0.406 10 false Rear Personal Light Switch RH 1.292,6.896 3.375,7.302 2.083,0.406 10 false S10 1.677,6.885 3.76,7.292 2.083,0.406 10 false Spot Light Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the lights operate.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Personal light and rear interior light ON/OFF
·

No. 1 room light assembly switch in DOOR position*1

·

Interior light door switch is on*1


*1: w/o Sliding Roof

*2: w/ Sliding Roof


Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4
OK:

Each light fades in.


Result:
Result Proceed to
OK A
NG (w/o Sliding Roof) B
NG (w/ Sliding Roof) C




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

4.INSPECT ROOF CONSOLE BOX ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Perform the check under the following condition:

·

No. 1 room light assembly switch in DOOR position*



Standard Voltage:
Tester Connection Condition Specified Condition
3B-35 - Body ground Engine switch off 11 to 14 V


*: w/o Sliding Roof



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E173026C07
1.146,0.344 1.438,0.521 0.292,0.177 4.646,0.344 4.938,0.521 0.292,0.177 3.01,1.115 3.01,1.469 3.01,1.469 3.115,1.469 false 0.156,0.104 0.313,0.25 0.156,0.146 10 *a 1.208,0.333 1.625,0.583 0.417,0.25 10 3B 4.688,0.333 5.188,0.552 0.5,0.219 10 MB 3.135,1.396 3.365,1.542 0.229,0.146 10 ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3B-35 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.INSPECT ROOF CONSOLE BOX ASSEMBLY
a.

Remove the roof console box assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the roof console box assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION

OK:

Roof console box assembly is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE ROOF CONSOLE BOX ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Install the roof console box assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSTALLATION


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

HINT:

Perform the check under the following condition:

·

Interior light door switch on



Standard Voltage:
Tester Connection Condition Specified Condition
3B-35 - Body ground Engine switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E173026C08
1.146,0.344 1.438,0.521 0.292,0.177 4.646,0.344 4.938,0.521 0.292,0.177 3.01,1.115 3.01,1.469 3.01,1.469 3.115,1.469 false 0.156,0.104 0.313,0.25 0.156,0.146 10 *a 1.208,0.344 1.552,0.573 0.344,0.229 10 3B 4.688,0.344 5.083,0.563 0.396,0.219 10 MB 3.135,1.396 3.365,1.542 0.229,0.146 10 ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3B-35 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY