GENERAL
The blind spot monitor system has the blind spot monitor function and RCTA function.
Blind spot monitor function
The blind spot monitor function is a function that assists the driver when changing lanes. The function uses quasi-millimeter wave radar to detect vehicles that are traveling in an adjacent lane in the area that is not visible in the mirror sub-assembly. The function advises the driver of the existence of a vehicle by illuminating the outer rear view mirror indicator on the mirror sub-assembly.
If the turn signal switch is operated while the outer rear view mirror indicator on a mirror sub-assembly is illuminated, the indicator starts blinking to give additional warning to the driver.
RCTA function
The RCTA function is a function that informs the driver of an approaching vehicle from diagonally behind. The function uses quasi-millimeter wave radar to detect the position and relative speed of other vehicles. When the function determines that a vehicle is approaching this vehicle, this function informs the driver of it using the outer rear view mirror indicators and blind spot monitor buzzer.
FUNCTION OF COMPONENTS
| Component | Function |
|---|---|
| Blind Spot Monitor Sensor | ·
Consists of a 24 GHz radar module and an integrated processing module. ·
Illuminates the outer rear view mirror indicator on the mirror sub-assembly when a vehicle is present in the blind spot area. ·
Sounds the RCTA buzzer (blind spot monitor buzzer) when the RCTA function is operating. ·
Changes the outer rear view mirror indicator on the mirror sub-assembly from illuminated to blinking when a turn signal is received from the combination meter assembly. ·
Dims the outer rear view mirror indicator on the mirror sub-assembly and blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly). ·
Turns on the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) when the blind spot monitor main switch (warning canceling switch assembly) is on. |
| Mirror Sub-assembly
·
Outer Rear View Mirror (Outer Rear View Mirror Indicator) |
Turns on or blinks the indicator based on a signal from the blind spot monitor sensor. |
| Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly)
·
Blind Spot Monitor Indicator |
·
Turns the blind spot monitor on or off. ·
Informs the state of the blind spot monitor system by illuminating the blind spot monitor indicator. |
| RCTA Buzzer (Blind Spot Monitor Buzzer) | Sounds based on a signal from the blind spot monitor sensor. |
| Combination Meter Assembly (Multi-information Display) | ·
Sends a turn signal state signal from the headlight dimmer switch assembly (turn signal light switch) to the blind spot monitor sensor via CAN communication. ·
Displays an error message on the multi-information display if the blind spot monitor detects a malfunction while it is operating. |
| Main Body ECU (Multiplex Network Body ECU) | Sends the destination information and the dimmer signal to the blind spot monitor sensor via CAN communication. |
| Brake Actuator Assembly
·
Skid Control ECU |
Transmits a vehicle speed signal to the blind spot monitor sensor via CAN communication. |
| ECM | Sends shift position signal (R) to the blind spot monitor sensor via CAN communication. |
| Steering Sensor | Detects the angle of the steering wheel and sends the resulting signals to the blind spot monitor sensor via CAN communication. |
OPERATION DESCRIPTION
Operation description of the blind spot monitor function
Operation conditions:
The blind spot monitor main switch (warning canceling switch assembly) is on.
Vehicle speed is more than approximately 16 km/h (10 mph).
Conditions in which a sensor can detect a vehicle
The blind spot monitor function indicates detection of a vehicle in the detection area when either condition is met:
When a vehicle is detected in an adjacent lane overtaking this vehicle.
When a vehicle is detected entering the detection area because it changed lanes.
| *a | Within Approx. 3.5 m (11.48 ft) from Side of Vehicle |
| *b | Within Approx. 3 m (9.84 ft) behind Rear Bumper |
| *c | Within Approx. 1 m (3.28 ft) forward of Rear Bumper |
|
Detection Area |
Detection area
Vehicles in the following areas can be detected:
Operation description of the RCTA function
Operation conditions:
The blind spot monitor main switch (warning canceling switch assembly) is on.
The shift lever is in R.
The vehicle speed is less than approximately 8 km/h (5 mph).
Conditions in which a sensor can detect a vehicle
The RCTA function indicates detection of a vehicle in the detection area when both conditions are met:
A vehicle is approaching this vehicle from diagonally behind.
The vehicle speed is approximately 8 km/h (5 mph) to 28 km/h (17 mph).
| *a | Within Approx. 5.5 to 20 m (18.05 to 65.62 ft) from Side of Vehicle (detection area changes according to vehicle speed) |
| *b | Within Approx. 6 m (19.69 ft) behind Rear Bumper |
|
Detection Area |
Detection area
Vehicles in the following areas can be detected:
OPERATION OF OUTER REAR VIEW MIRROR INDICATOR AND RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
Initial check
When the blind spot monitor main switch (warning canceling switch assembly) is turned on with the engine switch on (IG), the outer rear view mirror indicators on the mirror sub-assembly illuminate for 3 seconds and the RCTA buzzer (blind spot monitor buzzer) sounds for 1 second.
When the engine switch is turned from off to on (IG) with the blind spot monitor main switch (warning canceling switch assembly) on, the outer rear view mirror indicators on the mirror sub-assembly illuminate for 3 seconds.
Operation for each function
Operation for blind spot monitor function
When a sensor detects a vehicle in the blind spot area, the outer rear view mirror indicator on the mirror sub-assembly illuminates.
While the sensor is detecting a vehicle in the detection area and the indicator is illuminated, if the turn signal switch is operated, the outer rear view mirror indicator on the mirror sub-assembly starts blinking as shown in the illustration.
Operation for RCTA function
When all of the operation conditions for the RCTA function are met, the outer rear view mirror indicators on the mirror sub-assembly blink for 2.5 seconds and the RCTA buzzer (blind spot monitor buzzer) sounds for 2.3 seconds as shown in the illustration.
| *a | 0.125 Seconds | *b | 2.5 Seconds |
| *c | 0.1 Seconds | *d | 0.4 Seconds |
| *e | 2.3 Seconds | - | - |