Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074560 BLIND SPOT MONITOR SYSTEM U

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (warning canceling switch assembly) OFF or ON ON: Blind spot monitor main switch (warning canceling switch assembly) ON
OFF: Blind spot monitor main switch (warning canceling switch assembly) OFF
-
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator RH turning on OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Right turn signal: OFF

·

Vehicle speed 16 km/h (10 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator RH flashing OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check


·

Vehicle detected in right hand side warning area


·

Right turn signal: ON


·

Vehicle speed 16 km/h (10 mph) or more


·

Shift lever in any position except R


·

Blind spot monitor warning light not illuminated


·

Vehicle detected by RCTA function



-
Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current The outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Turn Switch State Master side, slave side state of the turn SW Left ON, Right ON or OFF Left ON: Left turn switch on
Right ON: Right turn switch on
OFF: Switch not operated
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch (warning canceling switch assembly) Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when the blind spot monitor main switch (warning canceling switch assembly) is changed from off to on during Test Mode.
Beam Axis Inspection Completeness Flag Completion of beam axis inspection Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz -
Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50% -
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
when a malfunction is detected: More than 0
-
Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator LH turning on OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Left turn signal: OFF

·

Vehicle speed 16 km/h (10 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator LH flashing OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Vehicle speed 16 km/h (10 mph) or more

·

Left turn signal: ON

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated

·

Vehicle detected by RCTA function



-
Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: Buzzer sounding
-
Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current The outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 V
-
Turn Switch State Master side, slave side state of the turn SW Left ON, Right ON or OFF Left ON: Left turn switch on
Right ON: Right turn switch on
OFF: Switch not operated
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag Completion of beam axis inspection Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz -
Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50% -
Buzzer Control Frequency Frequency of the RCTA buzzer (blind spot monitor buzzer) when sounding Min.: 1000 Hz, Max.: 2400 Hz Always: 2000 Hz -
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
when a malfunction is detected: More than 0
-