Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0076716 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals sent from the combination meter assembly.


for "Bluetooth":

Vehicle speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio and display receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E316128E01
0.146,2.438 3.052,2.625 2.906,0.188 10 false Certification ECU (Smart Key ECU Assembly) 0.24,3.677 2.927,3.865 2.688,0.188 10 false Stereo Component Amplifier Assembly*4 0.365,4.906 2.771,5.146 2.406,0.24 10 false Windshield Wiper Relay Assembly*5 4.99,3.698 7.052,3.927 2.063,0.229 10 false Navigation Receiver Assembly*1 0.427,6.083 2.75,6.302 2.323,0.219 10 false Headlight Leveling ECU Assembly*6 4.625,4.917 7.104,5.146 2.479,0.229 10 false Radio and Display Receiver Assembly*2 5.156,6.094 6.885,6.313 1.729,0.219 10 false Radio Receiver Assembly*3 6.042,7.302 6.469,7.5 0.427,0.198 10 false ECM 5.198,2.51 7.052,2.719 1.854,0.208 10 false Combination Meter Assembly 0.479,1.281 3.313,1.49 2.833,0.208 10 false Brake Actuator Assembly (Skid Control ECU) 2.823,5.135 4.094,5.333 1.271,0.198 10 false Junction Connector 1.344,7.323 1.75,7.531 0.406,0.208 10 false TCM 0.344,7.927 2.313,8.156 1.969,0.229 10 false *1: for Navigation Receiver Type 2.656,7.917 4.625,8.146 1.969,0.229 10 false *2: for Radio and Display Type 4.865,7.927 6.833,8.156 1.969,0.229 10 false *3: for Radio Receiver Type 0.344,8.333 2.313,8.563 1.969,0.229 10 false *4: for 10 Speakers 1.792,8.344 3.542,8.583 1.75,0.24 10 false *5: w/ Auto Wiper System 3.635,8.333 7.073,8.573 3.438,0.24 10 false *6: w/ Automatic Headlight Beam Level Control System 0.156,1.292 0.49,1.5 0.333,0.208 10 false A49 0.167,2.26 0.5,2.469 0.333,0.208 10 false I78 0.25,3.51 0.583,3.719 0.333,0.208 10 false I69 0.365,4.74 0.698,4.948 0.333,0.208 10 false I72 0.427,5.927 0.76,6.135 0.333,0.208 10 false A78 1.083,7.323 1.333,7.531 0.25,0.208 10 false E7 5.719,7.302 6.052,7.51 0.333,0.208 10 false A25 5.156,5.917 5.573,6.125 0.417,0.208 10 false I150 4.635,4.75 5.052,4.958 0.417,0.208 10 false I155 4.99,3.521 5.406,3.729 0.417,0.208 10 false I67 5.198,2.344 5.615,2.552 0.417,0.208 10 false I18 1.708,1.99 2.042,2.198 0.333,0.208 10 false SPD 1.698,3.25 2.031,3.458 0.333,0.208 10 false SPD 1.688,4.458 2.021,4.667 0.333,0.208 10 false SPD 1.615,5.635 2.052,5.833 0.438,0.198 10 false SPDR 1.708,6.854 2.063,7.021 0.354,0.167 10 false SPD 5.594,6.854 5.948,7.021 0.354,0.167 10 false SPD 5.594,5.635 5.948,5.802 0.354,0.167 10 false SPD 5.594,4.458 5.948,4.625 0.354,0.167 10 false SPD 5.594,3.24 5.948,3.406 0.354,0.167 10 false SPD 0.854,0.396 1.188,0.604 0.333,0.208 10 false SP1 2.823,4.969 3.156,5.177 0.333,0.208 10 false I185 1.229,0.396 1.563,0.604 0.333,0.208 10 false 2 2.104,2 2.438,2.208 0.333,0.208 10 false 27 2.094,3.25 2.427,3.458 0.333,0.208 10 false 11 2.115,4.458 2.448,4.667 0.333,0.208 10 false 24 2.104,5.635 2.438,5.844 0.333,0.208 10 false 16 2.115,6.854 2.448,7.063 0.333,0.208 10 false 3 5.333,6.844 5.5,7.094 0.167,0.25 10 false 10 5.323,5.635 5.49,5.802 0.167,0.167 10 false 17 5.313,4.458 5.479,4.625 0.167,0.167 10 false 17 5.323,3.24 5.49,3.406 0.167,0.167 10 false 17 5.385,0.406 5.552,0.615 0.167,0.208 10 false 4 5.375,1.99 5.542,2.198 0.167,0.208 10 false 3 5.604,2.073 5.854,2.281 0.25,0.208 10 false +S 5.615,0.479 5.865,0.688 0.25,0.208 10 false SI 3.948,1.99 4.115,2.198 0.167,0.208 10 false 18 2.906,1.99 3.073,2.198 0.167,0.208 10 false 15 2.906,3.25 3.073,3.458 0.167,0.208 10 false 19 3.958,3.25 4.125,3.458 0.167,0.208 10 false 17 2.917,4.438 3.083,4.646 0.167,0.208 10 false 20 3.938,4.448 4.104,4.656 0.167,0.208 10 false 16


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

While driving the vehicle, compare the value displayed for "SPEED" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E286967C28
1.5,0.333 1.917,0.583 0.417,0.25 2.135,1.354 2.667,0.667 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.604,0.365 2.063,0.563 0.458,0.198 10 false I18 2.667,0.5 3.125,0.698 0.458,0.198 10 false +S 1.115,3.844 1.427,4.042 0.313,0.198 10 false A 2.781,3.594 3.24,3.792 0.458,0.198 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265791C23
1.646,0.271 2.063,0.531 0.417,0.26 2.604,1.844 2.406,1.406 false 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.698,0.323 2.323,0.688 0.625,0.365 10 false I155 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.781,1.729 5.094,1.927 0.313,0.198 10 false A 6.167,1.469 6.594,1.688 0.427,0.219 10 false GND
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -


i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I155-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I155-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I155 radio and display receiver assembly connector.


b.

Disconnect the I185 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-17 (SPD) - I185-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINTION METER ASSEMBLY - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINTION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the I185 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (SPD) - I185-18 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)