Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0076716 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E226165E97
0.948,0.771 1.802,0.979 0.854,0.208 10 false from Battery 0.729,1.573 1.802,1.75 1.073,0.177 10 false from ACC Relay 0.427,2.375 1.833,2.552 1.406,0.177 10 false from IG1 NO. 1 Relay 3.396,1.031 4.323,1.208 0.927,0.177 10 false RADIO-B 3.385,1.823 4.292,2 0.906,0.177 10 false ECU-ACC 3.25,2.604 4.51,2.781 1.26,0.177 10 false ECU-IG1 NO. 2 5.531,2.979 5.729,3.146 0.198,0.167 10 false 7 5.531,1.375 5.729,1.542 0.198,0.167 10 false 3 5.448,0.802 5.917,1.021 0.469,0.219 10 false I152 5.438,1.583 6,1.833 0.563,0.25 10 false I152 5.427,2.375 5.938,2.698 0.51,0.323 10 false I155 5.427,3.167 5.781,3.333 0.354,0.167 10 false I152 5.813,0.781 6.104,0.948 0.292,0.167 10 false +B1 5.813,1.583 6.25,1.75 0.438,0.167 10 false ACC1 5.813,2.375 5.99,2.542 0.177,0.167 10 false IG 5.813,3.167 6.25,3.333 0.438,0.167 10 false GND1 5.573,3.625 6.781,4.229 1.208,0.604 10 false Radio and Display Receiver Assembly 5.531,0.583 5.656,0.75 0.125,0.167 10 false 4 5.531,2.167 5.656,2.333 0.125,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the I152 and I155 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I152-4 (+B1) - I152-7 (GND1) Always 11 to 14 V
I152-3 (ACC1) - I152-7 (GND1) Ignition switch ACC 11 to 14 V
I155-1 (IG) - I152-7 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR