Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM2030EQ _53 Suspension _052590 TIRE PRESSURE MONITORING _0265589 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

The order in which the data is received is random.

·

If the signals from all the tire pressure warning valve and transmitters are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

Initialization is normally completed within a few minutes.

·

It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21

·

If initialization has not been completed successfully, DTC C2177/77 is stored after a vehicle speed of 40 km/h (25 mph) or more is detected for 20 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the tire pressure warning reset switch is pushed.

·
C217594C07
1.781,1.458 2.052,1.76 true 1.573,1.073 1.365,1.76 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 1.969,1.792 2.49,1.969 0.521,0.177 10 false TC 1.198,1.792 1.552,1.969 0.354,0.177 10 false CG
*a Front view of DLC3


Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.



BEFORE INITIALIZATION


a.

Set the tire pressure to the specified value.

NOTICE:

Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION




INITIALIZATION PROCEDURE


HINT:

The tire pressure warning system illuminates the tire pressure warning light to warn the driver when any of the following conditions are met:

·

Due to the operation of the tire pressure warning reset switch, the tire pressure drops to approximately 80% or less of the tire pressure set during system initialization.

·

The tire pressure drastically decreases (approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more within several minutes) to approximately 80% or less of the tire pressure* when the tires are warmed.

*: If initialization is performed and the vehicle is driven for a certain period of time, the tire pressure set during system initialization is adjusted and set to the tire pressure when the tires are warmed from the driving conditions.

NOTICE:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




a.

Turn the engine switch on (IG).


b.
C353635C01
0.677,0.167 0.99,0.323 0.313,0.156 10 false *1 2.458,0.167 2.771,0.323 0.313,0.156 10 false *2 0.208,3.229 0.521,3.385 0.313,0.156 10 false *a 2.271,3.375 2.583,3.531 0.313,0.156 10 false *b 0.583,3.719 0.896,3.875 0.313,0.156 10 false *c 0.594,3.969 0.906,4.125 0.313,0.156 10 false *d 1.99,4.281 2.302,4.438 0.313,0.156 10 false *b
*1 Tire Pressure Warning Light
*2 Tire Pressure Warning Reset Switch
*a Tire Pressure Warning Light Output Pattern
*b 1 sec.
*c ON
*d OFF


Press and hold the tire pressure warning reset switch for 3 seconds or more until the tire pressure warning light blinks 3 times.


c.

Turn the engine switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.