Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.05
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to GND (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

ECM

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Brake actuator assembly

·

Steering sensor

·

Network gateway ECU

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (Certification ECU)

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

Clearance warning ECU assembly

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



*1: for Navigation Receiver Type

*2: for Radio and Display Type

WIRING DIAGRAM

C325912E02
0.083,0.083 0.792,0.333 0.708,0.25 12 false V Bus: 0.604,0.531 1.063,0.729 0.458,0.198 10 false I18 0.854,0.531 2.781,0.792 1.927,0.26 10 false Combination Meter Assembly 2.792,0.792 3.406,0.99 0.615,0.198 10 false CANL 4.135,0.792 4.75,0.99 0.615,0.198 10 false CANH 3.469,0.198 4.24,0.396 0.771,0.198 10 false 120 Ω 4.094,1.052 4.406,1.25 0.313,0.198 10 false 17 3.01,1.052 3.323,1.25 0.313,0.198 10 false 16 4.135,1.344 4.292,1.542 0.156,0.198 10 false R 2.979,1.344 3.135,1.542 0.156,0.198 10 false W 3.948,1.646 4.406,1.844 0.458,0.198 10 false I94 3.167,1.646 3.625,1.844 0.458,0.198 10 false I94 4.271,1.583 4.427,1.781 0.156,0.198 10 false 1 2.917,1.604 3.073,1.802 0.156,0.198 10 false 2 2.708,1.802 2.865,2 0.156,0.198 10 false 1 2.719,2.583 2.875,2.781 0.156,0.198 10 false 2 2.635,2.375 3.25,2.573 0.615,0.198 10 false I112 2.635,2.01 3.25,2.208 0.615,0.198 10 false I112 2.01,1.792 2.323,1.99 0.313,0.198 10 false P 1.979,2.594 2.135,2.792 0.156,0.198 10 false W 1.542,2.49 1.854,2.708 0.313,0.219 10 false 18 1.542,1.885 1.854,2.104 0.313,0.219 10 false 17 1.24,1.896 1.552,2.094 0.313,0.198 10 false R1 1.25,2.5 1.563,2.698 0.313,0.198 10 false R2 0.052,2.729 0.51,2.927 0.458,0.198 10 false I82 0.292,2.729 1.49,3.281 1.198,0.552 10 false Clearance Warning ECU Assembly 2.677,4.208 3.135,4.406 0.458,0.198 10 false I97 2.677,3.854 3.135,4.052 0.458,0.198 10 false I97 2.708,3.615 2.865,3.813 0.156,0.198 10 false 1 2.719,4.438 2.875,4.635 0.156,0.198 10 false 2 2.01,3.625 2.167,3.823 0.156,0.198 10 false V 1.99,4.417 2.146,4.615 0.156,0.198 10 false W 1.552,3.719 1.708,3.917 0.156,0.198 10 false 3 1.552,4.333 1.708,4.531 0.156,0.198 10 false 2 1.073,4.333 1.688,4.531 0.615,0.198 10 false CANL 1.052,3.708 1.667,3.906 0.615,0.198 10 false CANH 0.073,4.583 0.531,4.781 0.458,0.198 10 false I29 0.313,4.583 2.604,4.781 2.292,0.198 10 false Steering Sensor 0.042,6.365 0.5,6.563 0.458,0.198 10 false A49 0.344,6.365 2.083,6.677 1.74,0.313 10 false Brake Actuator Assembly 1.042,5.5 1.656,5.698 0.615,0.198 10 false CANH 1.052,6.135 1.667,6.333 0.615,0.198 10 false CANL 1.531,5.49 1.844,5.688 0.313,0.198 10 false 26 1.531,6.167 1.844,6.365 0.313,0.198 10 false 14 1.771,5.417 2.083,5.615 0.313,0.198 10 false GR 1.813,6.188 1.969,6.385 0.156,0.198 10 false W 2.25,5.438 2.406,5.635 0.156,0.198 10 false Y 2.229,6.198 2.385,6.396 0.156,0.198 10 false W 2.635,6 3.25,6.198 0.615,0.198 10 false I105 2.625,5.635 3.24,5.833 0.615,0.198 10 false I105 2.698,5.406 2.854,5.604 0.156,0.198 10 false 1 2.708,6.229 2.865,6.427 0.156,0.198 10 false 2 0.813,8.01 2.76,8.281 1.948,0.271 10 false : CAN Main Bus Line (CANH) 0.823,8.427 2.729,8.708 1.906,0.281 10 false : CAN Main Bus Line (CANL) 3.906,7.198 4.521,7.396 0.615,0.198 10 false I101 3.135,7.198 3.75,7.396 0.615,0.198 10 false I101 4.271,7.229 4.427,7.427 0.156,0.198 10 false 1 2.927,7.208 3.083,7.406 0.156,0.198 10 false 2 4.135,7.5 4.292,7.698 0.156,0.198 10 false B 2.969,7.5 3.125,7.698 0.156,0.198 10 false W 3.958,7.99 5.896,8.24 1.938,0.25 10 false : CAN Branch Line (CANH) 3.969,8.417 5.813,8.688 1.844,0.271 10 false : CAN Branch Line (CANL) 4.927,0.281 6.365,0.552 1.438,0.271 10 false x: Suspected Area 4.406,2.01 6.5,2.292 2.094,0.281 10 false CAN No. 2 Junction Connector 4.406,2.792 5.021,2.99 0.615,0.198 10 false I106 4.417,3.167 5.031,3.365 0.615,0.198 10 false I106 4.479,2.563 4.635,2.76 0.156,0.198 10 false 1 4.5,3.396 4.656,3.594 0.156,0.198 10 false 2 5.219,2.615 5.375,2.813 0.156,0.198 10 false L 5.198,3.354 5.354,3.552 0.156,0.198 10 false W 5.573,2.688 5.885,2.885 0.313,0.198 10 false 14 5.573,3.281 5.885,3.479 0.313,0.198 10 false 15 5.833,2.688 6.448,2.885 0.615,0.198 10 false CANH 5.844,3.292 6.458,3.49 0.615,0.198 10 false CANL 5.177,3.542 5.635,3.74 0.458,0.198 10 false I78 5.427,3.542 7.125,3.927 1.698,0.385 10 false Smart Key ECU Assembly (Certification ECU) 4.448,4.708 4.906,4.906 0.458,0.198 10 false I96 4.448,5.063 4.906,5.26 0.458,0.198 10 false I96 4.49,4.49 4.646,4.688 0.156,0.198 10 false 1 4.5,5.281 4.656,5.479 0.156,0.198 10 false 2 5.208,4.458 5.365,4.656 0.156,0.198 10 false G 5.198,5.281 5.354,5.479 0.156,0.198 10 false W 5.688,4.594 5.844,4.792 0.156,0.198 10 false 6 5.823,5.167 6.135,5.365 0.313,0.198 10 false 14 5.885,4.667 6.5,4.865 0.615,0.198 10 false CANH 6.052,5.031 6.667,5.229 0.615,0.198 10 false CANL 6.104,5.26 6.563,5.458 0.458,0.198 10 false I39 6.344,5.26 6.958,5.458 0.615,0.198 10 false DLC3

C325913E01
0.094,0.073 1.198,0.313 1.104,0.24 12 false V Bus: 0.042,2.25 0.5,2.448 0.458,0.198 10 false I67 0.281,2.25 2.406,2.521 2.125,0.271 10 false Navigation Receiver Assembly*1 0.042,2.563 0.656,2.76 0.615,0.198 10 false I155 0.344,2.563 2.885,2.865 2.542,0.302 10 false Radio and Display Receiver Assembly*2 1.042,1.385 1.656,1.583 0.615,0.198 10 false CANH 1.052,2.01 1.667,2.208 0.615,0.198 10 false CANL 1.552,1.396 1.708,1.594 0.156,0.198 10 false 9 1.521,2 1.833,2.198 0.313,0.198 10 false 10 2.083,1.344 2.24,1.542 0.156,0.198 10 false R 2.063,2.083 2.219,2.281 0.156,0.198 10 false W 2.594,1.51 3.208,1.708 0.615,0.198 10 false I107 2.594,1.885 3.208,2.083 0.615,0.198 10 false I107 2.667,1.271 2.823,1.469 0.156,0.198 10 false 1 2.688,2.104 2.844,2.302 0.156,0.198 10 false 2 3.156,0.583 3.615,0.781 0.458,0.198 10 false I93 3.917,0.583 4.375,0.781 0.458,0.198 10 false I93 4.229,0.573 4.385,0.771 0.156,0.198 10 false 1 2.906,0.573 3.063,0.771 0.156,0.198 10 false 2 2.583,4.25 3.198,4.448 0.615,0.198 10 false I102 2.583,3.885 3.198,4.083 0.615,0.198 10 false I102 2.656,3.656 2.813,3.854 0.156,0.198 10 false 1 2.667,4.469 2.823,4.667 0.156,0.198 10 false 2 2.083,3.677 2.24,3.875 0.156,0.198 10 false V 2.063,4.469 2.219,4.667 0.156,0.198 10 false W 1.51,3.75 1.823,3.948 0.313,0.198 10 false 11 1.521,4.385 1.833,4.583 0.313,0.198 10 false 12 0.99,3.75 1.604,3.948 0.615,0.198 10 false CANH 1.01,4.396 1.625,4.594 0.615,0.198 10 false CANL 0.052,4.615 0.51,4.813 0.458,0.198 10 false I77 0.302,4.615 1.521,5.198 1.219,0.583 10 false Air Conditioning Amplifier Assembly 2.594,5.99 3.208,6.188 0.615,0.198 10 false I161 2.594,5.625 3.208,5.823 0.615,0.198 10 false I161 2.667,5.417 2.823,5.615 0.156,0.198 10 false 1 2.677,6.219 2.833,6.417 0.156,0.198 10 false 2 2.031,5.469 2.344,5.667 0.313,0.198 10 false BE 2.052,6.208 2.208,6.406 0.156,0.198 10 false W 1.531,5.5 1.844,5.698 0.313,0.198 10 false 16 1.542,6.135 1.854,6.333 0.313,0.198 10 false 15 1.042,5.521 1.656,5.719 0.615,0.198 10 false CA1H 1.052,6.125 1.667,6.323 0.615,0.198 10 false CA1L 0.052,6.365 0.667,6.563 0.615,0.198 10 false I160 0.354,6.365 3.26,6.563 2.906,0.198 10 false Network Gateway ECU 3.875,6.51 4.49,6.708 0.615,0.198 10 false I104 4.24,6.552 4.396,6.75 0.156,0.198 10 false 1 2.885,6.542 3.042,6.74 0.156,0.198 10 false 2 3.115,6.51 3.729,6.708 0.615,0.198 10 false I104 0.156,7.76 1.5,8.042 1.344,0.281 10 false x: Suspected Area 0.094,7.427 2.417,7.76 2.323,0.333 10 false *2: for Radio and Display Type 0.083,7.083 2,7.365 1.917,0.281 10 false *1: Navigation Receiver Type 0.813,9.042 2.823,9.333 2.01,0.292 10 false : CAN Main Bus Line (CANH) 0.813,9.438 2.865,9.75 2.052,0.313 10 false : CAN Main Bus Line (CANL) 2.958,7.531 3.115,7.729 0.156,0.198 10 false W 2.948,6.948 3.104,7.146 0.156,0.198 10 false W 4.156,6.948 4.313,7.146 0.156,0.198 10 false G 4.167,7.542 4.323,7.74 0.156,0.198 10 false B 2.76,8.083 3.375,8.281 0.615,0.198 10 false CANL 4.094,8.094 4.708,8.292 0.615,0.198 10 false CANH 2.969,7.823 3.281,8.021 0.313,0.198 10 false 26 4.073,7.833 4.385,8.031 0.313,0.198 10 false 13 4.625,8.375 5.083,8.573 0.458,0.198 10 false A25 3.438,8.688 4.208,8.885 0.771,0.198 10 false 120 Ω 4.927,8.375 5.385,8.573 0.458,0.198 10 false ECM 3.969,9.073 6.042,9.406 2.073,0.333 10 false : CAN Branch Line (CANH) 3.958,9.458 5.75,9.771 1.792,0.313 10 false : CAN Branch Line (CANL) 4.385,6.333 6.438,6.604 2.052,0.271 10 false CAN No. 1 Junction Connector 4.427,4.667 4.885,4.865 0.458,0.198 10 false I95 4.427,5.042 4.885,5.24 0.458,0.198 10 false I95 4.458,4.448 4.615,4.646 0.156,0.198 10 false 1 4.469,5.271 4.625,5.469 0.156,0.198 10 false 2 5.156,4.479 5.313,4.677 0.156,0.198 10 false P 5.135,5.26 5.292,5.458 0.156,0.198 10 false W 5.25,5.417 5.708,5.615 0.458,0.198 10 false I13 5.49,5.417 7.125,6.042 1.635,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 5.542,4.552 5.854,4.75 0.313,0.198 10 false 14 5.542,5.177 5.854,5.375 0.313,0.198 10 false 13 5.792,4.542 6.406,4.74 0.615,0.198 10 false CANH 5.802,5.177 6.417,5.375 0.615,0.198 10 false CANL 4.385,3.198 5,3.396 0.615,0.198 10 false I103 4.385,2.833 5,3.031 0.615,0.198 10 false I103 4.458,2.625 4.615,2.823 0.156,0.198 10 false 1 4.469,3.417 4.625,3.615 0.156,0.198 10 false 2 5.156,2.625 5.313,2.823 0.156,0.198 10 false Y 5.135,3.417 5.292,3.615 0.156,0.198 10 false W 5.313,3.583 5.771,3.781 0.458,0.198 10 false I47 5.552,3.583 7.125,3.844 1.573,0.26 10 false Airbag Sensor Assembly 5.531,2.708 5.844,2.906 0.313,0.198 10 false 13 5.542,3.333 5.854,3.531 0.313,0.198 10 false 22 5.802,3.333 6.417,3.531 0.615,0.198 10 false CANL 5.802,2.708 6.417,2.906 0.615,0.198 10 false CANH 4.396,1.323 5.01,1.521 0.615,0.198 10 false I100 4.396,0.948 5.01,1.146 0.615,0.198 10 false I100 4.469,0.729 4.625,0.927 0.156,0.198 10 false 1 4.49,1.542 4.646,1.74 0.156,0.198 10 false 2 4.885,0.781 5.042,0.979 0.156,0.198 10 false L 4.854,1.5 5.01,1.698 0.156,0.198 10 false W 5.354,0.781 5.51,0.979 0.156,0.198 10 false Y 5.313,1.5 5.625,1.698 0.313,0.198 10 false SB 5.625,0.833 5.781,1.031 0.156,0.198 10 false 4 5.625,1.427 5.781,1.625 0.156,0.198 10 false 8 5.813,0.833 6.427,1.031 0.615,0.198 10 false CANH 5.813,1.438 6.427,1.635 0.615,0.198 10 false CANL 5.656,1.688 5.969,1.885 0.313,0.198 10 false j1 5.833,1.698 7.135,2.219 1.302,0.521 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the engine switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 52 seconds, and drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C254055C01
2.104,1.698 2.448,1.927 0.344,0.229 2.646,2.146 2.521,2.146 2.521,2.146 2.313,2.25 false 2.656,2.583 2.531,2.583 2.531,2.583 2.313,2.406 false 2.156,2.438 2.229,2.896 2.229,2.896 2.302,2.896 false 2.094,2.313 1.979,2.198 1.979,2.198 1.823,2.198 false 0.167,0.177 0.469,0.5 0.302,0.323 10 false *a 2.677,2.063 3.24,2.219 0.563,0.156 10 false CANH*b 2.677,2.49 3.24,2.646 0.563,0.156 10 false CANL*b 1.656,2.115 1.792,2.26 0.135,0.146 10 false G 2.344,2.813 2.521,2.969 0.177,0.156 10 false W 2.177,1.719 2.531,1.979 0.354,0.26 10 false I96
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to DLC3


Disconnect the I96 DLC3 branch line connector from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C03
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.219,1.313 2.219,1.313 2.427,1.313 false 2.063,2.563 2.25,2.99 2.25,2.99 2.385,2.99 false 1.625,1.865 1.406,1.313 1.406,1.313 1.208,1.313 false 0.135,0.156 0.979,0.49 0.844,0.333 10 *1 1.625,0.76 2.26,1.146 0.635,0.385 10 I39 2.49,1.24 3.094,1.51 0.604,0.271 10 CANH 0.938,1.25 1.438,1.448 0.5,0.198 10 CG 2.438,2.906 3.354,3.313 0.917,0.406 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Reconnect the I96 DLC3 branch line connector to the CAN No. 2 junction connector.


b.
C210421C03
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.219,1.313 2.219,1.313 2.427,1.313 false 2.063,2.563 2.25,2.99 2.25,2.99 2.385,2.99 false 1.625,1.865 1.406,1.313 1.406,1.313 1.208,1.313 false 0.135,0.156 0.979,0.49 0.844,0.333 10 *1 1.625,0.76 2.26,1.146 0.635,0.385 10 I39 2.49,1.24 3.094,1.51 0.604,0.271 10 CANH 0.938,1.25 1.438,1.448 0.5,0.198 10 CG 2.438,2.906 3.354,3.313 0.917,0.406 10 CANL
*1 DLC3


Disconnect the connectors from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.

HINT:

Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.



c.

Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.

C326012C02
1.167,2.396 1.521,2.667 0.354,0.271 10 false *1 2.063,1.688 2.417,1.958 0.354,0.271 10 false *2 2.958,2.396 3.271,2.594 0.313,0.198 10 false *3 3.854,1.677 4.167,1.875 0.313,0.198 10 false *4 4.75,2.385 5.063,2.583 0.313,0.198 10 false *5 5.646,1.667 5.958,1.865 0.313,0.198 10 false *6 0.885,1.49 1.198,1.688 0.313,0.198 10 false P 1.438,1.49 1.781,1.781 0.344,0.292 10 false W 1.823,1.104 1.979,1.302 0.156,0.198 10 false V 2.333,1.104 2.677,1.396 0.344,0.292 10 false W 2.76,1.115 2.917,1.313 0.156,0.198 10 false Y 2.656,1.844 2.969,2.042 0.313,0.198 10 false GR 3.219,1.115 3.563,1.406 0.344,0.292 10 false W 3.229,1.844 3.573,2.135 0.344,0.292 10 false W 3.635,1.115 3.792,1.313 0.156,0.198 10 false L 4.135,1.115 4.479,1.406 0.344,0.292 10 false W 4.49,1.479 4.646,1.677 0.156,0.198 10 false G 5.031,1.479 5.375,1.771 0.344,0.292 10 false W 5.427,1.115 5.583,1.313 0.156,0.198 10 false R 5.917,1.115 6.26,1.406 0.344,0.292 10 false W 6.323,2.313 6.479,2.51 0.156,0.198 10 false B 6.875,2.313 7.125,2.542 0.25,0.229 10 false W 0.073,3.625 0.229,3.823 0.156,0.198 10 false B 0.573,3.625 0.729,3.823 0.156,0.198 10 false W 0.844,4.104 1.917,4.302 1.073,0.198 10 false *7 (*A) 0.844,4.323 1.917,4.521 1.073,0.198 10 false *8 (*B) 0.74,5.125 0.896,5.323 0.156,0.198 10 false R 1.25,5.125 1.406,5.323 0.156,0.198 10 false W 1.906,4.865 2.219,5.063 0.313,0.198 10 false *9 1.646,5.24 1.802,5.438 0.156,0.198 10 false B 1.646,5.75 1.802,5.948 0.156,0.198 10 false G 2.188,5.24 2.344,5.438 0.156,0.198 10 false W 2.198,5.75 2.354,5.948 0.156,0.198 10 false W 2.865,4.229 3.323,4.427 0.458,0.198 10 false *10 2.677,4.813 2.833,5.01 0.156,0.198 10 false Y 3.156,4.813 3.469,5.01 0.313,0.198 10 false SB 2.677,5.604 2.833,5.802 0.156,0.198 10 false L 3.188,5.604 3.344,5.802 0.156,0.198 10 false W 3.844,4.875 4.302,5.073 0.458,0.198 10 false *11 3.656,5.542 3.813,5.74 0.156,0.198 10 false Y 4.167,5.542 4.323,5.74 0.156,0.198 10 false W 4.885,4.208 5.344,4.406 0.458,0.198 10 false *12 4.667,5.313 4.823,5.51 0.156,0.198 10 false V 5.219,5.313 5.375,5.51 0.156,0.198 10 false W 5.667,4.885 6.125,5.083 0.458,0.198 10 false *13 6.563,4.219 7.021,4.417 0.458,0.198 10 false *14 3.448,0.333 3.906,0.531 0.458,0.198 10 false *15 3.417,6.281 3.875,6.479 0.458,0.198 10 false *16 5.49,5.594 5.646,5.792 0.156,0.198 10 false P 5.99,5.594 6.146,5.792 0.156,0.198 10 false W 6.323,5.292 6.635,5.49 0.313,0.198 10 false BE 6.896,5.302 7.052,5.5 0.156,0.198 10 false W
*A for Navigation Receiver Type *B for Radio and Display Type
*1 Clearance Warning ECU Assembly *2 Steering Sensor
*3 Brake Actuator Assembly *4 Smart Key ECU Assembly (Certification ECU)
*5 DLC3 *6 Combination Meter Assembly
*7 Navigation Receiver Assembly *8 Radio and Display Receiver Assembly
*9 ECM *10 Power Steering ECU Assembly
*11 Airbag Sensor Assembly *12 Air Conditioning Amplifier Assembly
*13 Main Body ECU (Multiplex Network Body ECU) *14 Network Gateway ECU
*15 CAN No. 2 Junction Connector *16 CAN No. 1 Junction Connector


C326013C01
2.333,0.448 2.646,0.646 0.313,0.198 10 false *a 3.573,2.313 4.188,2.51 0.615,0.198 10 false I101 3.615,2.594 4.073,2.792 0.458,0.198 10 false I94 3.625,2.854 4.083,3.052 0.458,0.198 10 false I96 3.594,3.146 4.208,3.344 0.615,0.198 10 false I106 3.594,3.417 4.208,3.615 0.615,0.198 10 false I105 3.625,3.708 4.083,3.906 0.458,0.198 10 false I97 3.583,4.01 4.198,4.208 0.615,0.198 10 false I112
*a Component without harness connected
(to CAN No. 2 Junction Connector)
- -


Wiring Color:
CAN No. 2 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I101 B W
Combination meter assembly I94 R W
DLC3 I96 G W
Smart key ECU assembly (certification ECU) I106 L W
Brake actuator assembly I105 Y W
Steering sensor I97 V W
Clearance warning ECU assembly I112 P W


C247978C01
3.354,2.604 3.802,2.771 0.448,0.167 10 false I95 3.313,2.323 3.76,2.49 0.448,0.167 10 false I161 3.313,3.156 3.76,3.323 0.448,0.167 10 false I103 3.313,2.875 3.76,3.042 0.448,0.167 10 false I102 3.344,4.25 3.792,4.417 0.448,0.167 10 false I93 3.313,3.979 3.76,4.146 0.448,0.167 10 false I107 3.313,3.438 3.76,3.604 0.448,0.167 10 false I100 2.427,0.385 2.625,0.583 0.198,0.198 10 false *a 3.313,3.708 3.76,3.875 0.448,0.167 10 false I104
*a Component without harness connected
(to CAN No. 1 Junction Connector)
- -


Wiring Color:
CAN No. 1 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Network gateway ECU I161 BE W
Main body ECU (multiplex network body ECU) I95 P W
Air conditioning amplifier assembly I102 V W
Airbag sensor assembly I103 Y W
Power steering ECU assembly I100 L W
ECM I104 G W
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


I107 R W
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I93 B W


*1: for Navigation Receiver Type

*2: for Radio and Display Type


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus lines.



Result:
Symptom Proceed to
The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector. (There is a short to GND in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) A
The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector. (There is a short to GND in one of the areas that relate to the disconnected bus lines.) B


d.

When there is a short to GND in one or more of the bus lines that connect to an ECU (or sensor):

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or higher) to confirm that there is a short to GND in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.





e.

When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:

i.

With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.




A

3.CHECK CAN NO. 2 JUNCTION CONNECTOR

B

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
3.CHECK CAN NO. 2 JUNCTION CONNECTOR
a.
C247984C02
2.771,1.521 3.073,1.75 0.302,0.229 2.458,1.865 2.563,1.865 2.563,1.865 2.885,2.146 false 2.365,2.719 2.875,2.719 2.875,2.719 2.875,2.354 false 2.344,2.333 2.802,2.333 false 2.354,2.083 2.438,2.083 2.438,2.083 2.813,2.208 false 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a 1.917,1.792 2.646,2.125 0.729,0.333 10 false CANH*b 2.219,2.021 2.375,2.219 0.156,0.198 10 false B 2.188,2.271 2.344,2.469 0.156,0.198 10 false W 1.833,2.635 2.563,2.969 0.729,0.333 10 false CANL*b 2.802,1.552 3.167,1.781 0.365,0.229 10 false I101
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector


Disconnect the I101 CAN main bus line connector from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C210421C03
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.219,1.313 2.219,1.313 2.427,1.313 false 2.063,2.563 2.25,2.99 2.25,2.99 2.385,2.99 false 1.625,1.865 1.406,1.313 1.406,1.313 1.208,1.313 false 0.135,0.156 0.979,0.49 0.844,0.333 10 *1 1.625,0.76 2.26,1.146 0.635,0.385 10 I39 2.49,1.24 3.094,1.51 0.604,0.271 10 CANH 0.938,1.25 1.438,1.448 0.5,0.198 10 CG 2.438,2.906 3.354,3.313 0.917,0.406 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

4.CHECK CAN NO. 1 JUNCTION CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)

NG

REPLACE CAN NO. 2 JUNCTION CONNECTOR

4.CHECK CAN NO. 1 JUNCTION CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the I101 CAN main bus line connector to the CAN No. 2 junction connector.


b.
C247984C01
2.719,1.375 3.177,1.656 0.458,0.281 2.875,2.146 2.417,1.854 2.417,1.854 2.167,1.854 false 2.875,2.365 2.875,2.698 2.875,2.698 2.198,2.698 false 2.74,2.219 2.438,2.083 2.438,2.083 2.302,2.083 false 2.813,2.333 2.365,2.333 false 0.094,0.094 0.375,0.302 0.281,0.208 10 false *a 1.635,1.781 2.281,2 0.646,0.219 10 false CANH*b 1.667,2.625 2.313,2.844 0.646,0.219 10 false CANL*b 2.854,1.427 3.146,1.594 0.292,0.167 10 false I93 2.177,2.01 2.313,2.198 0.135,0.188 10 false B 2.208,2.26 2.385,2.448 0.177,0.188 10 false W
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector


Disconnect the I93 CAN main bus line connector from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C03
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.219,1.313 2.219,1.313 2.427,1.313 false 2.063,2.563 2.25,2.99 2.25,2.99 2.385,2.99 false 1.625,1.865 1.406,1.313 1.406,1.313 1.208,1.313 false 0.135,0.156 0.979,0.49 0.844,0.333 10 *1 1.625,0.76 2.26,1.146 0.635,0.385 10 I39 2.49,1.24 3.094,1.51 0.604,0.271 10 CANH 0.938,1.25 1.438,1.448 0.5,0.198 10 CG 2.438,2.906 3.354,3.313 0.917,0.406 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS MAIN LINE (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or higher when it was disconnected).


b.
C210421C03
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.219,1.313 2.219,1.313 2.427,1.313 false 2.063,2.563 2.25,2.99 2.25,2.99 2.385,2.99 false 1.625,1.865 1.406,1.313 1.406,1.313 1.208,1.313 false 0.135,0.156 0.979,0.49 0.844,0.333 10 *1 1.625,0.76 2.26,1.146 0.635,0.385 10 I39 2.49,1.24 3.094,1.51 0.604,0.271 10 CANH 0.938,1.25 1.438,1.448 0.5,0.198 10 CG 2.438,2.906 3.354,3.313 0.917,0.406 10 CANL
*1 DLC3


Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR