Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2012.02–2015.04
NM2040EQ _54 Brake _014497 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0073595 BRAKE CONTROL SYSTEM GE GENERAL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The brake actuator and the skid control ECU have been integrated and a hydraulic brake booster has been provided, thus optimizing the hydraulic circuit and offering a weight reduction.


b.

The brake control functions (ABS with EBD, Brake Assist, TRC, VSC and Hill-start Assist Control) are provided.


c.

The VSC that performs the cooperative control with the EPS is used.


d.

An electronically controlled brake system is used to control the hydraulic pressure at the 4 wheels.


e.

Regenerative brake cooperative control is used.



MAIN FEATURES


a.

Electronically Controlled Brake System

i.

In this system, the conventional brake booster portion has been discontinued. Instead, it consists of a hydraulic brake booster, brake actuator and brake booster pump assembly.


ii.

During normal braking, the fluid pressure generated by the hydraulic brake booster does not directly actuate the wheel cylinders, but serves as a hydraulic pressure signal. Instead, the actual control pressure is obtained by regulating the fluid pressure of the brake booster pump assembly, which actuates the wheel cylinders.

X103420
5.052,5.854 4.49,7.021 4.49,7.021 4.406,7.021 true 2.531,0.771 3.365,0.135 3.365,0.135 3.448,0.135 true 5.875,5.031 5.781,5.031 5.781,5.031 5.385,5.573 true 4.531,2.604 6.656,2.927 2.125,0.323 10 false Power Steering ECU Assembly 4.5,3.604 6.667,4.042 2.167,0.438 10 false Power Management Control ECU 5.958,4.885 6.813,5.292 0.854,0.406 10 false Regenerative Brake Force 3.375,6.885 4.385,7.313 1.01,0.427 10 false Hydraulic Brake Force 4.969,7.438 5.813,7.698 0.844,0.26 10 false Brake Force 2.281,5.229 4.125,5.438 1.844,0.208 10 false Hydraulic Control Portion 0.427,5.25 1.906,5.646 1.479,0.396 10 false Hydraulic Power Source Portion 5.51,0.208 6.813,0.438 1.302,0.229 10 false : Electrical Signal 5.521,0.49 6.844,0.719 1.323,0.229 10 false : Fluid Pressure 0.51,2.615 2.208,2.885 1.698,0.271 10 false Skid Control ECU 1.583,1.552 2.646,2.021 1.063,0.469 10 false Master Cylinder Pressure Sensor 3.5,0.01 4.917,0.635 1.417,0.625 10 false Brake Pedal Stroke Sensor 0.521,3.115 3.063,3.469 2.542,0.354 10 false - Normal Brake, ABS with EBD, Brake Assist, TRC and VSC 0.531,3.729 3.146,4.073 2.615,0.344 10 false - Regenerative Brake Cooperative Control 0.521,4.208 3.167,4.458 2.646,0.25 10 false - Power Steering Cooperative Control 0.5,5.854 1.854,6.448 1.354,0.594 10 false - Generates hydraulic power using the pump 2.333,5.781 4.24,6.448 1.906,0.667 10 false - Hydraulic power is adjusted to the required braking force, and distributes it to each wheel 4.51,4.104 6.146,4.375 1.635,0.271 10 false - Regenerative Braking 4.552,2.969 5.615,3.281 1.063,0.313 10 false - Steering Assist


iii.

When the skid control ECU detects a fault in the system, brake force can be ensured by applying the brake using the fluid pressure boosted by the hydraulic brake booster.



b.

Regenerative Brake Cooperative Control

i.

Regenerative braking consists of a resistance force that is generated at the rotational axle in the reverse direction of the rotation of the generator (MG2) that is generating electricity. The greater the generated amperage (battery charging amperage), the greater will be the resistance force.

X101531C02
4.156,0.427 4.344,0.667 0.188,0.24 10 false *a 4.188,1.198 4.375,1.438 0.188,0.24 10 false *b 4.104,2.563 4.406,2.74 0.302,0.177 10 false *3 2.531,2.521 2.833,2.698 0.302,0.177 10 false *4 0.417,2.563 0.719,2.74 0.302,0.177 10 false *3 4.813,1.76 5.115,1.938 0.302,0.177 10 false *1 5.958,1.729 6.26,1.906 0.302,0.177 10 false *2 6.219,2.531 6.521,2.708 0.302,0.177 10 false *4 5.354,3.333 5.656,3.51 0.302,0.177 10 false *c 2.292,1.74 2.594,1.917 0.302,0.177 10 false *2 1.125,1.771 1.427,1.948 0.302,0.177 10 false *1 0.448,0.479 0.677,0.688 0.229,0.208 10 false *a 0.448,1.198 0.677,1.406 0.229,0.208 10 false *b 1.656,3.333 1.885,3.542 0.229,0.208 10 false *c
*1 MG1 *2 Inverter
*3 Engine *4 MG2
*a Rotating direction to electricity generation *b Resistance
*c Brake Force - -



ii.

The drive wheels and MG2 are joined mechanically. When the drive wheels rotate MG2 and cause it to operate as a generator, a regenerative brake force of MG2 is transmitted to the drive wheels. Based on the signals from the skid control ECU, this force is controlled by the hybrid system, which controls the generation of electricity.


iii.

The regenerative brake cooperative control does not rely solely on the braking force of the hydraulic brake system to supply the brake force required by the driver. Instead, by effecting cooperative control with the hybrid system, this control provides a joint braking force provided by the regenerative braking and the hydraulic braking. As a result, this control minimizes the loss of the kinetic energy associated with the normal hydraulic braking, and recovers this energy by converting it into electrical energy.


iv.

The apportioning of the brake force between the hydraulic braking and the regenerative braking varies by the vehicle speed and time.


v.

The apportioning of the brake force between the hydraulic braking and the regenerative braking is accomplished by controlling the hydraulic braking so that the total brake force of the hydraulic braking and the regenerative braking matches the brake force required by the driver.


vi.

If the regenerative braking becomes inoperative due to a malfunction in the hybrid system, the brake system effects control so that the entire brake force required by the driver is supplied with the hydraulic brake system.

X101475
2.573,0.229 2.75,0.229 2.75,0.229 3.365,1.156 true 4.646,0.927 4.5,0.927 4.5,0.927 4.333,1.177 true 1.26,0.927 1.833,1.344 0.573,0.417 10 false Braking Force 1.677,0.083 2.573,0.573 0.896,0.49 10 false Hydraulic Braking Force 4.708,0.823 5.792,1.104 1.083,0.281 10 false Driver's Demand 3.646,2.146 4.531,2.563 0.885,0.417 10 false Regenerative Braking Force 4.552,2.896 4.948,3.135 0.396,0.24 10 false Time 2.188,3.229 4.823,3.583 2.635,0.354 10 false Changes in Braking Force Apportionment



c.

VSC

i.

In the past, the brake control functions (ABS, TRC, VSC) and the Electronic Power Steering (EPS) were controlled individually. In contrast, the new model uses the VSC, which uses a cooperative control with EPS. This system effects a control integrated the brake control functions and the EPS in accordance with driving conditions. Thus, it realizes the dynamic performance of the vehicle to "run, turn and stop" and ensures excellent driving stability and drivability.

X104970
2.833,0.271 4.813,0.604 1.979,0.333 10 false - Steering Angle Signal 2.833,0.604 5.813,0.938 2.979,0.333 10 false - Yawrate Signal 2.833,0.99 5.688,1.323 2.854,0.333 10 false - Master Cylinder Pressure Signal 3.615,1.792 5.354,1.948 1.74,0.156 10 false Various Sensor Signals 4.625,2.125 6.698,2.448 2.073,0.323 10 false Power Steering ECU Assembly 1.229,2.281 3.01,2.708 1.781,0.427 10 false Actual Locus of Travel (Front Wheel Skid Tendency) 2.51,2.979 3.354,3.719 0.844,0.74 10 false Locus of Travel Based on the Target Yaw Rate 1.323,5.542 2.229,5.813 0.906,0.271 10 false Brake Control 3.969,2.729 5.24,3.125 1.271,0.396 10 false Power Management Control ECU 3.802,3.792 4.948,4.219 1.146,0.427 10 false Motive Force Control Command 5.135,3.781 6.552,4.302 1.417,0.521 10 false Steering Torque Assist Control Command 4.271,4.698 6,5.01 1.729,0.313 10 false Control Volume Calculation 3.302,5.448 4.885,5.938 1.583,0.49 10 false Four Wheel Independent Brake Control Command 5.198,5.438 6.802,5.927 1.604,0.49 10 false Vehicle Driving Condition Detection and Calculation 4.594,6.26 6,6.573 1.406,0.313 10 false Skid Control ECU 2.844,1.375 5.698,1.708 2.854,0.333 10 false - Throttle Position Signal




PRECAUTION


a.

When the brake control system is activated, the brake pedal could shudder, which is a normal occurrence of the system in operation and should not be considered as a malfunction.