Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
NM2040EQ _51 Engine / Hybrid System _014483 HYBRID / BATTERY CONTROL _0073580 HYBRID CONTROL SYSTEM DE DETAILS F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  DETAILS  INVERTER WITH CONVERTER  


CONSTRUCTION


a.

A compact, lightweight inverter with converter assembly, in which the MG ECU, inverter, boost converter, and DC-DC converter are integrated, is used. The inverter and boost converter primarily consist of Intelligent Power Modules (IPMs), a reactor, and capacitor. The IPM is an integrated power module consisting of a signal processor, protective function processor, and Insulated Gate Bipolar Transistors (IGBTs).


b.

The inverter with converter assembly ensures heat dissipation through use of a water-cooled cooling system that is isolated from the engine cooling system.


c.

As a safety measure because of the high-voltage, interlock switches are provided, which shut off the system main relays via the power management control ECU when the connector cover or terminal cover is removed, or the HV battery power cable connector is disconnected.

W113236
1.229,1.229 1.542,1.427 0.313,0.198 10 false *1 1.375,2.177 1.688,2.375 0.313,0.198 10 false *2
*1 Inverter *2 DC-DC Converter
V100135

HV Coolant Inlet
V100136

HV Coolant Outlet



d.

The inverter uses the IPM to perform switching control. The IPMs for MG1 and MG2 each have a bridge circuit consisting of IGBTs. The IPM for MG1 uses 6 IGBTs, one for each arm, and MG2 uses 6 pairs of IGBTs, two in parallel for each arm.


e.

The boost converter uses a boost IPM to perform switching control, a reactor to act as an inductor, and a capacitor to accumulate and store electricity. The boost IPM uses IGBT2 for boosting voltage, and IGBT1 for reducing voltage.

W105555
1.031,4.167 1.521,4.417 0.49,0.25 10 false IGBT 1.458,0.615 1.948,0.865 0.49,0.25 10 false MG1 0.969,6.854 1.542,7.104 0.573,0.25 10 false IGBT1 1.354,1.385 1.594,1.635 0.24,0.25 10 false U 1.646,1.385 1.885,1.635 0.24,0.25 10 false V 1.938,1.385 2.177,1.635 0.24,0.25 10 false W 1.813,6.854 2.385,7.104 0.573,0.25 10 false IGBT2 1.177,4.76 2.104,5.01 0.927,0.25 10 false IPM for MG1 3.052,4.771 3.979,5.021 0.927,0.25 10 false IPM for MG2* 0.656,7.208 1.583,7.458 0.927,0.25 10 false Boost IPM* 1.75,7.406 2.354,7.656 0.604,0.25 10 false Reactor 1.302,5.365 1.99,5.542 0.688,0.177 10 false Capacitor 3.99,5.719 4.552,5.969 0.563,0.25 10 false Inverter 3.385,6.281 4.063,6.531 0.677,0.25 10 false MG ECU 1.677,8.969 2.719,9.219 1.042,0.25 10 false HV Battery 0.438,7.896 1.542,8.125 1.104,0.229 10 false Boost Converter 3.219,7.292 4.406,7.542 1.188,0.25 10 false DC-DC Converter 5.208,8.094 6.667,8.51 1.458,0.417 10 false Compressor with Motor Assembly 4.854,1.813 6.229,2.26 1.375,0.448 10 false Inverter with Converter Assembly 3.354,0.615 3.844,0.865 0.49,0.25 10 false MG2 3.26,1.385 3.5,1.635 0.24,0.25 10 false U 3.552,1.385 3.792,1.635 0.24,0.25 10 false V 3.844,1.385 4.083,1.635 0.24,0.25 10 false W 5.344,6.781 6.615,7.24 1.271,0.458 10 false Power Management Control ECU 0.323,9.375 4.99,9.583 4.667,0.208 10 false *: Single IGBTs have been used to represent pairs of IGBTs for simplicity.

1.

MG ECU

1.

The MG ECU is provided in the inverter with converter assembly. In accordance with the signals received from the power management control ECU, the MG ECU controls the inverter and boost converter in order to drive MG1 or MG2 or cause them to generate electricity.

2.

The MG ECU transmits information that is required for vehicle control, such as the atmospheric pressure, inverter temperature and any failure information, to the power management control ECU. The MG ECU receives information that is required for controlling MG1 and MG2, such as the required motive force and the temperature of MG1 and MG2, from the power management control ECU.


2.

Atmospheric Pressure Sensor

1.

The atmospheric pressure sensor is provided on the MG ECU board.

2.

This sensor detects the atmospheric pressure and transmits a signal to the MG ECU to allow corrections that correspond to the usage environment.


3.

Temperature Sensor for Inverter with Converter Assembly

1.

For the inverter with converter assembly, there are 5 different temperature sensors; 2 of them are located at the IPMs for MG1 and MG2, 2 of them are located at the boost converter, and the remaining sensor is located at the HV coolant passage.

2.

These sensors detect the temperatures at areas inside the inverter with converter assembly, and transmit that temperature information to the power management control ECU via the MG ECU. The power management control ECU optimizes the cooling system according to the temperature information, maintaining the output performance of the inverter with converter assembly.

W101640
1.271,0.948 2.198,1.198 0.927,0.25 10 IPM for MG1 3.167,1.063 4.094,1.313 0.927,0.25 10 IPM for MG2 4,1.688 4.906,1.938 0.906,0.25 10 Inverter 3.188,2.948 3.865,3.198 0.677,0.25 10 MG ECU 1.802,1.417 2.063,1.667 0.26,0.25 10 *1 3.708,1.417 3.969,1.667 0.26,0.25 10 *2 1.313,2.229 1.573,2.479 0.26,0.25 10 *3 2.281,2.24 2.542,2.49 0.26,0.25 10 *4 4.188,2.292 4.448,2.542 0.26,0.25 10 *5 0.594,3.656 1.698,4.104 1.104,0.448 10 Boost Converter 1.521,4.302 4.615,4.583 3.094,0.281 10 Inverter with Converter Assembly 0.427,4.646 3.115,4.906 2.688,0.26 10 *1: Temperature Sensor on IPM for MG1 0.427,5.021 3.115,5.281 2.688,0.26 10 *2: Temperature Sensor on IPM for MG2 0.427,5.406 3.604,5.813 3.177,0.406 10 *3: Temperature Sensor on Boost IPM (Upper) 3.771,4.646 6.896,4.948 3.125,0.302 10 *4: Temperature Sensor on Boost IPM (Lower) 3.771,5.01 6.208,5.271 2.438,0.26 10 *5: HV Coolant Temperature Sensor 5.083,2.083 6.333,2.354 1.25,0.271 10 HV Coolant Flow 5.438,2.781 6.677,3.573 1.24,0.792 10 Power Management Control ECU 0.698,3.281 1.625,3.531 0.927,0.25 10 Boost IPM


4.

Inverter Current Sensor

1.

The inverter current sensors detect the amperage of the three-phase alternating current that actuates MG1 and MG2. This actual amperage is used as feedback by the MG ECU.

2.

The current sensors are used for the current sent to the three-phase windings of MG1 and MG2. The current sensors are located in the inverter with converter assembly for the V and W phases of each motor generator. Current that flows through the U phase winding flows through the V phase or W phase winding, thus the U phase amperage can be measured even if the current sensor is not set in the U phase winding.

W101641
3.438,1.469 3.271,0.438 3.271,0.438 2.792,0.438 true 3.667,1.667 3.865,0.438 3.865,0.438 4.198,0.438 true 3.271,2.875 3.948,3.125 0.677,0.25 10 false MG ECU 1.531,6.635 1.99,6.885 0.458,0.25 10 false MG1 1.667,4.771 1.885,5.021 0.219,0.25 10 false 9 1.667,5.51 1.885,5.76 0.219,0.25 10 false 5 1.958,6.635 2.375,6.885 0.417,0.25 10 false -300 4.083,6.583 4.5,6.833 0.417,0.25 10 false 0 5.979,6.646 6.396,6.896 0.417,0.25 10 false 300 1.531,6.854 1.99,7.104 0.458,0.25 10 false MG2 1.958,6.865 2.375,7.115 0.417,0.25 10 false -600 5.979,6.865 6.396,7.115 0.417,0.25 10 false 600 1.667,6.281 1.885,6.531 0.219,0.25 10 false 1 4.865,0.979 5.073,1.177 0.208,0.198 10 false U 4.375,1.75 4.583,1.948 0.208,0.198 10 false V 5.188,1.76 5.396,1.958 0.208,0.198 10 false W 4.146,2.073 5.74,2.292 1.594,0.219 10 false Motor Generator 0.156,3.885 3.583,4.188 3.427,0.302 12 false Characteristics of Inverter Current Sensor: 4.281,0.333 5.823,0.552 1.542,0.219 10 false Inverter Current Sensor 2.177,2.406 3.083,2.656 0.906,0.25 10 false Inverter 0.542,5.354 1.5,5.917 0.958,0.563 10 false Sensor Output Voltage (V) 3.813,7.313 4.76,7.583 0.948,0.271 10 false Current (A) 1.333,0.323 2.792,0.583 1.458,0.26 10 false Inverter Current Sensor