Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
NM2040EQ _51 Engine / Hybrid System _014483 HYBRID / BATTERY CONTROL _0081498 HYBRID BATTERY SYSTEM CO CONTROL F

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  CONTROL  POWER MANAGEMENT CONTROL ECU  


SYSTEM CONTROL


a.

State Of Charge (SOC)

i.

The power management control ECU estimates the SOC of the HV battery from the accumulated amperage that is constantly and repeatedly being charged and discharged. In order to maintain the SOC at the appropriate level all the time, the power management control ECU controls the hybrid system optimally.

W101107
1.917,1.948 1.927,0.938 1.927,0.938 1.604,0.938 true 2.948,1.771 2.938,0.906 2.938,0.906 3.271,0.906 true 0.333,0.823 1.646,1.167 1.313,0.344 10 false SOC Control Target 3.344,0.792 5.135,1.125 1.792,0.333 10 false Example of change in SOC 0.417,1.76 0.823,2.125 0.406,0.365 10 false SOC 2.271,2.76 2.75,3.073 0.479,0.313 10 false Time 5.323,1.521 6.927,1.865 1.604,0.344 10 false Upper SOC Control Limit 5.198,1.875 6.333,2.229 1.135,0.354 10 false Control Region 5.323,2.229 6.917,2.646 1.594,0.417 10 false Lower SOC Control Limit



b.

Detection of Insulation Resistance Decrease

i.

The leak detection circuit is built in the battery smart unit. The leak detection circuit constantly monitors that the insulation resistance between high-voltage circuits and body ground is maintained.


ii.

The power management control ECU determines decreases in the insulation resistance based on the information from the battery smart unit.


iii.

The leak detection circuit has an AC source and it causes a small amount of AC to flow to the high-voltage circuit (positive and negative).


iv.

The more insulation resistance decreases, the more voltage drops at the detection resistor and the lower the waves of AC. The insulation resistance value is detected based on the amplitude of AC waves.

W101611
0.344,0.208 2.521,0.385 2.177,0.177 10 false Power Management Control ECU 3.802,0.188 5.958,0.385 2.156,0.198 10 false Combination Meter Assembly 3.802,0.542 5.865,0.76 2.063,0.219 10 false - Multi-information Display 2.656,0.656 3.563,0.896 0.906,0.24 10 false CAN (V Bus) 3.885,1.906 4.938,2.125 1.052,0.219 10 false HV Battery 0.833,2.813 1.646,3.031 0.813,0.219 10 false AC Source 5.115,2.854 7.125,3.073 2.01,0.219 10 false Insulation Resistance 3.281,1.208 4.646,1.427 1.365,0.219 10 false High-voltage Circuit 0.833,1.885 2,2.104 1.167,0.219 10 false Voltage Detection 0.833,3.135 2.51,3.354 1.677,0.219 10 false Battery Smart Unit 0.833,2.375 2.104,2.594 1.271,0.219 10 false Detection Resistor 5.313,1.604 6.594,1.823 1.281,0.219 10 false High-voltage Load 1.458,1.24 3.042,1.49 1.583,0.25 10 false Serial Communication



c.

Cut-off of High-Voltage Circuits during Collision

i.

If the vehicle is involved in a collision as described below, the power management control ECU will shut down the power supply by turning the system main relays off for safety.


ii.

The power management control ECU receives the airbag deployment signal from the airbag sensor assembly during a frontal collision, side collision or side rear collision.

W105420
5.281,0.927 6.563,1.333 1.281,0.406 10 false Power Management Control ECU 3.021,0.938 3.927,1.427 0.906,0.49 10 false Airbag Sensor Assembly 4.052,1.594 4.938,1.813 0.885,0.219 10 false CAN (V Bus) 0.375,1.656 1.323,1.875 0.948,0.219 10 false Side Collision 0.188,1.958 1.51,2.177 1.323,0.219 10 false Side Rear Collision 0.292,0.76 1.406,0.979 1.115,0.219 10 false Frontal Collision 5.125,2.396 6.896,2.615 1.771,0.219 10 false System Main Relays OFF 2.01,1.698 2.531,1.917 0.521,0.219 10 false Impact