Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT
NM2040EQ _51 Engine / Hybrid System _014484 2AR-FXE ENGINE MECHANICAL _0073581 ENGINE UNIT DE DETAILS F

2AR-FXE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

The cylinder block sub-assembly is made of aluminum alloy, so it is lightweight.


b.

Water passages have been provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.


c.

The liners are a spiny-type, which have been manufactured so that their cast outers form large irregular surfaces in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.

W105431
4.719,1.354 4.719,0.26 4.719,0.26 5.448,0.26 true 2.938,3.177 2.177,3.177 true 4.198,3.271 3.698,3.271 true 1.354,0.604 1.479,0.76 0.125,0.156 10 false A 1.906,0.948 2.031,1.104 0.125,0.156 10 true A 5.5,0.156 6.469,0.302 0.969,0.146 10 false *1 2.021,3.052 2.948,3.198 0.927,0.146 10 false *2 3.188,4.25 3.385,4.417 0.198,0.167 10 false *b 4.25,3.167 6.479,3.49 2.229,0.323 10 false *a
*1 Water Passage *2 Cylinder Block Sub-assembly
*a Spiny-type Liner (Irregularly Shaped Outer Casting Surface of Liner) *b A-A Cross Section



d.

Blowby gas passages are provided in the crankcase.


e.

Oil drain passages are provided in the crankcase. This prevents the crankshaft from churning the engine oil, reducing rotational resistance.


f.

The oil filter bracket is integrated into the crankcase.

W100793
3.135,1 3.135,0.208 3.135,0.208 3.406,0.208 true 2.792,1.125 2.792,0.198 2.792,0.198 2.542,0.198 true 3.604,0.917 3.604,0.552 3.604,0.552 4.76,0.552 true 4.323,1.583 4.323,2 true 3.021,2.146 3.021,2.448 true 2.365,1.26 2.365,0.708 2.365,0.708 2,0.708 true 3.479,0.115 4.844,0.333 1.365,0.219 10 *1 4.844,0.469 6.042,0.646 1.198,0.177 10 *2 4.26,2.031 4.469,2.219 0.208,0.188 10 *4 2.958,2.49 3.146,2.635 0.188,0.146 10 *3 1.802,0.615 2.01,0.802 0.208,0.188 10 *2 2.354,0.104 2.542,0.271 0.188,0.167 10 *1
*1 Blowby Gas Passage *2 Oil Drain Passage
*3 Oil Filter Bracket *4 Crankcase



g.

An oil separator is provided in the blow-by gas passage inside the cylinder block sub-assembly. This separates the engine oil from the blow-by gas in order to reduce oil degradation and reduce the amount of engine oil consumed.

W105432
2.635,1.813 2.635,3.229 true 4.146,2.625 4.146,3.271 4.146,3.271 3.51,3.271 true 5.115,2.771 5.115,0.729 5.115,0.729 5.708,0.729 true 2.563,3.26 2.75,3.438 0.188,0.177 10 false *1 3.333,3.156 3.521,3.333 0.188,0.177 10 false *2 5.76,0.625 5.948,0.802 0.188,0.177 10 false *3
*1 Oil Separator *2 Case Separator
*3 Ventilation Case Sub-assembly - -



h.

Through the use of an offset crankshaft, the centerline of the bores is shifted 10 mm (0.39 in.) towards the exhaust side in relation to the centerline of the crankshaft. Thus, the side force to the cylinder wall is reduced when the maximum pressure is applied. This contributes to fuel economy.

W105433
4.552,2.396 3.896,2.396 3.896,2.396 3.896,2.896 true 5.885,2.396 5.229,2.396 5.229,2.396 5.229,2.885 true 0.885,1.063 1.083,1.25 0.198,0.188 10 false *c 3.208,1.063 3.427,1.292 0.219,0.229 10 false *d 2.083,0.521 2.281,0.688 0.198,0.167 10 false *a 2.021,3.188 2.208,3.354 0.188,0.167 10 false *b 3.833,2.906 4.031,3.083 0.198,0.177 10 false *b 4.604,0.469 4.802,0.667 0.198,0.198 10 false *e 5.813,0.469 6.031,0.667 0.219,0.198 10 false *e 4.646,3.385 4.833,3.615 0.188,0.229 10 false *f 6,3.385 6.271,3.646 0.271,0.26 10 false *g 5.188,2.917 5.385,3.094 0.198,0.177 10 false *b
*a Bore Centerline *b Crankshaft Centerline
*c Intake Side *d Exhaust Side
*e Maximum Pressure *f Offset Crankshaft
*g Non-offset Crankshaft - -



i.

A shallow bottom water jacket is used. The resulting reduction in the volume of the engine coolant improves warm-up performance, which contributes to improved fuel economy.


j.

A water jacket spacer is provided in the water jacket of the cylinder block sub-assembly.


k.

The water jacket spacer suppresses the water flow in the bottom of the water jackets, guides the coolant in the upper area of the water jacket, and ensures uniform temperature distribution. As a result, the viscosity of the engine oil that acts as a lubricant between the bore walls and the pistons can be lowered, thus reducing friction.

W105434
2.792,1.656 2.792,3.177 true 5.219,1.875 4.771,1.875 true 5.51,0.302 5.26,0.302 5.26,0.302 5.26,0.927 true 2.719,3.198 3.583,3.51 0.865,0.313 10 false *1 4.594,1.76 4.792,1.938 0.198,0.177 10 false *1 5.552,0.167 6.406,0.333 0.854,0.167 10 false *2 2.542,1.26 2.656,1.406 0.115,0.146 10 true A 3.073,1.635 3.188,1.781 0.115,0.146 10 true A 5.458,3.083 5.625,3.24 0.167,0.156 10 false *a
*1 Water Jacket Spacer *2 Water Jacket
*a A-A Cross Section - -