Home › Engine / Hybrid System › 2AR-FXE EMISSION CONTROL › EMISSION CONTROL SYSTEM
NM2040EQ _51 Engine / Hybrid System _014486 2AR-FXE EMISSION CONTROL _0073583 EMISSION CONTROL SYSTEM CO CONTROL F

2AR-FXE EMISSION CONTROL  EMISSION CONTROL SYSTEM  CONTROL  EMISSION CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the 2AR-FXE emission control system are as follows.

Component Function
TWC Oxidizes CO and HC in the exhaust gas and deoxidizes NOx at the same time, to purify them into CO2, H2O and N2.
Oxygen Sensor This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Air Fuel Ratio Sensor As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust gas. However, it detects the oxygen concentration in the exhaust gas linearly.
E.F.I. Vacuum Sensor Assembly Uses built-in semiconductors to detect the intake manifold pressure.
EGR Valve Assembly Operates when receiving signals from the ECM, regulating the EGR volume.
EGR Cooler Cools the exhaust gas temperature to improve the EGR efficiency.
Charcoal Canister Assembly Contains activated charcoal to absorb the fuel vapor that is created in the fuel tank assembly.
Canister Filter Prevents dust and debris in the fresh air from entering the system.
Fresh Air Line Fresh air goes into the charcoal canister assembly and the cleaned drain air goes out into the atmosphere.
Purge VSV Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister assembly into the intake manifold. In system monitoring mode, this valve controls the introduction of vacuum into the fuel tank assembly.
ECM
·

Controls the volume of fuel injected, with corrections based primarily on the signal from the air fuel ratio sensor, and minor corrections based on the signal from the oxygen sensor. This control optimizes the air-fuel ratio.

·

Regulates the EGR volume in accordance with the various sensor signals.

·

Controls the canister pump module and the purge VSV in accordance with the signals from various sensors, in order to achieve a purge volume that suits the driving conditions. In addition, the ECM monitors the system for any leaks and stores a DTC if a malfunction is found.





SYSTEM CONTROL


a.

EGR Control

i.

For the EGR system, a regulated amount of inert gas is allowed to flow into the intake passage, reducing the peak temperature in the engine combustion chamber.


ii.

By sensing the engine driving conditions and actual amount of the EGR valve opening, the ECM operates the EGR valve and throttle control motor, to regulate the amount of exhaust gas that is recirculated.

W113240
5.188,2.813 5.594,2.813 true 5.125,2.021 5.292,2.021 5.292,2.021 5.719,1.792 true 0.854,0.563 2.302,0.771 1.448,0.208 10 false Crank Position Sensor 0.229,0.979 2.302,1.24 2.073,0.26 10 false E.F.I. Vacuum Sensor Assembly 0.552,1.344 2.271,1.771 1.719,0.427 10 false Intake Mass Air Flow Meter Sub-assembly 0.396,1.948 2.292,2.208 1.896,0.26 10 false Intake Air Temperature Sensor 0.927,2.396 2.271,2.813 1.344,0.417 10 false E.F.I. Engine Coolant Temperature Sensor 0.448,3.115 1.698,3.531 1.25,0.417 10 false Power Management Control ECU 0.604,4.208 1.729,4.635 1.125,0.427 10 false Accelerator Pedal Sensor Assembly 2.104,3.573 2.958,3.833 0.854,0.26 10 false CAN (V Bus) 4.073,0.583 6.052,0.823 1.979,0.24 10 false Throttle Position Sensor Signal 4.083,1.052 6.063,1.292 1.979,0.24 10 false Throttle Valve Control 4.094,1.479 6.073,1.719 1.979,0.24 10 false EGR Valve Control 4.417,1.917 5.115,2.323 0.698,0.406 10 false EGR Valve Assembly 4.385,2.708 5.156,3.125 0.771,0.417 10 false EGR Cooler Assembly 6.458,3.208 6.927,3.427 0.469,0.219 10 false Engine 0.708,4.896 1.771,5.125 1.063,0.229 10 false : Exhaust Gas 0.708,5.344 1.771,5.573 1.063,0.229 10 false : Intake Air 3.333,2.24 3.719,2.469 0.385,0.229 10 false ECM



b.

Purge Flow Control

i.

When the engine has reached a predetermined state (closed loop, engine coolant temperature above 80°C (176°F), etc.), stored fuel vapor is purged from the charcoal canister assembly whenever the purge VSV is opened by the ECM.


ii.

The ECM will change the duty ratio cycle of the purge VSV, thus controlling purge flow volume. Purge flow volume is determined by intake manifold pressure and the duty ratio cycle of the purge VSV. Atmospheric pressure is allowed into the charcoal canister assembly to ensure that purge flow is constantly maintained whenever purge vacuum is applied to the charcoal canister assembly.

W100095
2.042,0.615 1.74,0.615 true 2.344,1.063 2.573,0.167 2.573,0.167 2.698,0.167 true 1.365,1.083 1.656,1.083 1.656,1.083 1.656,1.25 true 3.156,1.583 3.396,0.469 3.396,0.469 3.51,0.469 true 0.604,0.531 1.74,0.698 1.135,0.167 10 to Intake Manifold 2.74,0.104 3.542,0.25 0.802,0.146 10 Atmosphere 0.625,0.979 1.406,1.323 0.781,0.344 10 Purge VSV (Open) 1.625,2.74 1.958,2.896 0.333,0.156 10 ECM 3.573,0.385 4.885,0.531 1.313,0.146 10 Fuel Tank Assembly 5.74,3.167 6.875,3.479 1.135,0.313 10 Charcoal Canister Assembly