FUNCTION OF MAIN COMPONENTS
The main components in the cruise control system have the following functions:
| Component | Function | |
|---|---|---|
| Cruise Control Switch | ON-OFF Button | Turns the cruise control system on and off. |
| CANCEL Switch | Transmits a cancel signal to the power management control ECU. | |
| +RES Switch | Transmits an accelerate or resume preset speed signal to the power management control ECU. | |
| -SET Switch | Transmits a decelerate or vehicle speed setting signal to the power management control ECU. | |
| Power Management Control ECU | Controls all functions of the cruise control system in accordance with the signals from switches, sensors and ECUs. | |
| Inverter with Converter Assembly | MG ECU | Built into the inverter with converter assembly. Controls the motive force of MG2 in accordance with signals from the power management control ECU. |
| ECM | Actuates the throttle control motor in accordance with the signals from the power management control ECU. | |
| Brake Booster with Master Cylinder Assembly | Skid Control ECU | Transmits the VSC operation signal to the power management control ECU. |
| Combination Meter Assembly | Cruise Control Indicator Light | ·
Based on a cruise control indicator operation signal sent by the power management control ECU, the combination meter assembly illuminates the cruise control indicator light when the cruise control system has been turned on using the ON-OFF button on the cruise control switch. ·
Based on a cruise control indicator operation signal sent by the power management control ECU, the combination meter assembly turns off the cruise control indicator light if a malfunction occurs in the cruise control system. |
| Cruise Control SET Indicator Light | Illuminates when the vehicle speed is set. | |
| Multi-information Display | Displays a warning message to alert the driver in accordance with a signal received from the power management control ECU. | |
| Throttle Body with Motor Assembly | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals from the ECM. |
| Throttle Position Sensor | Detects the throttle valve opening angle and outputs it to the ECM. | |
| Hybrid Vehicle Transaxle Assembly | MG2 | Generates motive force for the wheels. |
| Speed Sensors | Detects the wheel speed of each of the 4 wheels. | |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression degree and transmits it to the power management control ECU. | |
| Shift Lever Position Sensor | Detects the shift lever position and transmits signals to the power management control ECU. | |
| Stop Light Switch Assembly | Detects the brake pedal being depressed and transmits its signal to the power management control ECU. | |
FUNCTION
The cruise control system has the following control functions:
| Function | Outline |
|---|---|
| Constant Speed Control | The power management control ECU compares the actual vehicle speed with the set speed. If the vehicle speed is higher than the set speed, the power management control ECU calculates optimal motive forces for the engine and MG2, and decelerates by adjusting the respective motive forces. If the vehicle speed is lower than the set speed, the power management control ECU calculates optimal motive forces for the engine and MG2, and accelerates by adjusting the respective motive forces. |
| Set Control | When this system fulfils the following conditions, and the cruise control switch is moved to the -SET side and released, the power management control ECU stores the vehicle speed and maintains the vehicle constantly at that speed.
·
The cruise control system has been turned on using the ON-OFF button on the cruise control switch. ·
The vehicle is driving at a speed of approximately 40 km/h (25 mph) or more. |
| Low Speed Limit Control | The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 40 km/h (25 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control is set and working to maintain vehicle speed, the cruise control will be canceled automatically. However, the set speed is kept in memory. |
| COAST Switch Control | When the cruise control switch is held to the -SET side, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will decelerate. ·
The set vehicle speed will change to the speed at which the vehicle is being driven when the COAST switch (-SET side operation) is released. |
| Tap Down Control | When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the -SET side, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will decelerate in increments of approximately 1.6 km/h (1 mph) each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed. |
| ACC Switch Control | When the cruise control switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will accelerate. ·
The set vehicle speed will change to the speed at which the vehicle is being driven when the switch is released. |
| Tap Up Control | When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the +RES side, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will accelerate in increments of approximately 1.6 km/h (1 mph) each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change. |
| RES Switch Control | If cruise control speed control operation is canceled for any reason other than a malfunction (except cancelation by operating the ON-OFF button on the cruise control switch) and the vehicle speed is more than the low speed limit, the vehicle can be returned to the speed which was stored before the cancelation of cruise operation by moving the cruise control switch to the +RES side. The stored vehicle speed can be resumed even if the vehicle speed drops below the low speed limit, because the speed in the memory has not been cleared. |
| Manual Cancel Control | If any of the following signals are sent to the power management control ECU, cruise control speed control operation is canceled accordingly.
·
Stop light switch on signal (The brake pedal is depressed.) ·
Signals indicating that the shift lever has been moved from D to another position. (The shift lever is moved from D to N or B.) ·
CANCEL switch on signal (The cruise control switch is moved to the CANCEL side.) ·
CANCEL switch on signal (The cruise control switch is moved to the CANCEL side.) ·
VSC operation |
| Automatic Cancel Control | If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Stop light switch open or short circuit Furthermore, the cruise control indicator light will turn off and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch, and the operation of the cruise control is disabled until the cruise control system is turned on again using the ON-OFF button. |
| If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Malfunction in the hybrid system Furthermore, cruise control operation is disabled until the cruise control system is turned on again using the ON-OFF button. |
|
| If any of the following conditions occur during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Stop light switch input signal is abnormality ·
Cancel circuit malfunction ·
Communication malfunction between the skid control ECU and power management control ECU Furthermore, the cruise control indicator light will turn off and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch, and the operation of the cruise control is disabled until the power switch is turned off. |
|
| If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control is set. |
|
| If the following condition occurs during cruise control speed control operation, cruise control speed control operation is canceled.
·
Vehicle speed decreases below the low speed limit (approximately 40 km/h [25 mph]). |
DIAGNOSIS
If a malfunction occurs in the cruise control system during cruise control operation, the power management control ECU automatically cancels control and turns off both the cruise control indicator light and the cruise control SET indicator light. At this time, "CHECK CRUISE CONTROL SYSTEM" is displayed on the multi-information display. The power management control ECU stores the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC).
The 5-digit DTC can be read by connecting the intelligent tester to DLC3. For details, refer to the Repair Manual.